Hi Jack
I found this email
http://www.mail-archive.com/casper@lists.berkeley.edu/msg02504.html
Then I used minicom and I replaced tcpborphserver2
root@roach:/usr/local/sbin# ls
fancontrol pwmconfig sensors-detect tcpborphserver2 tgtap
flash_eraseall sensord tb2server-allfix tcpborphserver2_old
root@roach:/usr/local/sbin#
After this worked tut2!
However, should I upgrade the versions of corr and katcp and filesystem?
This is the output of ?help
rolando@rolando-MS-7815:~$ telnet 192.168.100.2 7147
Trying 192.168.100.2...
Connected to 192.168.100.2.
Escape character is '^]'.
#version poco-0.1
#build-state poco-0.0a271150300
?help
#help sensor-dump dump\_sensor\_tree\_(?sensor-dump)
#help sensor-value query\_a\_sensor\_(?sensor-value\_sensor)
#help sensor-sampling
configure\_sensor\_(?sensor-sampling\_sensor\_[strategy\_[parameter]])
#help sensor-list lists\_available\_sensors\_(?sensor-list\_[sensor])
#help client-list displays\_client\_list\_(?client-list)
#help tap-stop stop\_a\_tgtap\_instance\_(?tap-stop\_register-name)
#help tap-start
start\_a\_tgtap\_instance\_(?tap-start\_tap-device\_register-name\_ip-address\_[port\_[mac]])
#help wordwrite
writes\_a\_word\_(?wordwrite\_register-name\_word-offset\_payload\_...)
#help wordread
reads\_a\_word\_(?wordread\_register-name\_word-offset\_length)
#help sysinit
writes\_the\_timing\_ctl\_register\_that\_resets\_the\_entire\_system\_(?sysinit)
#help write
write\_a\_given\_payload\_to\_an\_offset\_in\_a\_register\_(?write\_register-name\_register-offset\_data-payload)
#help bulkread
reads\_a\_given\_number\_of\_bytes\_from\_an\_offset\_in\_a\_register\_in\_a\_form\_suitable\_for\_large\_transfers\_(?bulkread\_register-name\_[register-offset\_[byte-count]])
#help read
reads\_a\_given\_number\_of\_bytes\_from\_an\_offset\_in\_a\_register\_(?read\_register-name\_[register-offset\_[byte-count]])
#help echotest
basic\_network\_echo\_tester\_(?echotest\_ip-address\_echo-port\_byte-count)
#help listdev lists\_available\_registers\_(?listdev)
#help delbof deletes\_a\_gateware\_image\_(?delbof\_image-file)
#help uploadbof
upload\_a\_gateware\_image\_(?uploadbof\_net-port\_filename\_[size])
#help listbof lists\_available\_gateware\_images\_(?listbof)
#help status reports\_if\_gateware\_has\_been\_programmed\_(?status)
#help progdev programs\_a\_gateware\_image\_(?progdev\_[image-file])
#help mode mode\_change\_command\_(?mode\_[new-mode])
#help watchdog pings\_the\_system\_(?watchdog)
#help log-level
sets\_the\_minimum\_reported\_log\_priority\_(?log-level\_[priority])
#help help displays\_this\_help\_(?help\_[command])
#help restart restarts\_the\_system\_(?restart)
#help halt shuts\_the\_system\_down\_(?halt)
!help ok 26
Regards
Rolando
2016-12-05 12:30 GMT-06:00 Jack Hickish <jackhick...@gmail.com>:
> Hi Rolando,
> Can you telnet into the roach using the command
>
> telnet <roach ip address> 7147
>
> You should be greeted by a welcome prompt. In the prompt, type
>
> ?help
>
> If you can paste the output of these commands in an email, maybe I can
> find you a version of the katcpserver which will work (assuming that's the
> problem)
>
> Cheers
> Jack
>
> On Mon, 5 Dec 2016, 09:30 Rolando Paz, <flx...@gmail.com> wrote:
>
>> Hi Jack
>>
>> I have a ROACH1 Rev.3, S/N 040433, and I'm using the file system that
>> came in the SD-Card to use ROACH.
>>
>> Is this what I need to update?
>>
>> Also, I am using corr-0.7.3 and katcp-0.3.4.
>>
>> What are the correct versions of corr and katcp for my ROACH? Or, should
>> I use casperfpga?
>>
>> Best Regard
>>
>> Rolando
>>
>> 2016-12-04 15:30 GMT-06:00 Jack Hickish <jackhick...@gmail.com>:
>>
>> Hi Rolando,
>>
>> If I had to guess, I'd say there is a problem with the version of the
>> python katcp/corr libraries you're using, and the version of tcpborphserver
>> running on your ROACH. Do you know the versions of these bits of code that
>> you're using?
>>
>> Cheers
>> Jack
>>
>> On Thu, 1 Dec 2016 at 16:52 Rolando Paz <flx...@gmail.com> wrote:
>>
>> Hello again
>>
>> I'm experimenting with the 10G port, however when I tried to run the
>> tut_2, the following problem arises:
>>
>> rolando@rolando-MS-7815:~/codigo_ROACH/tut2$ sudo python tut2.py
>> 192.168.100.2 -s
>> [sudo] password for rolando:
>> Connecting to server 192.168.100.2... ok
>>
>> ------------------------
>> Programming FPGA... ok
>> ---------------------------
>> Disabling output... done
>> ---------------------------
>> Port 0 linkup: True
>> Port 3 linkup: True
>> ---------------------------
>> Configuring receiver core... <type 'exceptions.RuntimeError'>
>> ('Request tap-start failed.\n Request: ?tap-start tap0 gbe3 192.168.3.16
>> 60000 02:02:C0:A8:03:10\n Reply: !tap-start fail.',)
>> Request tap-start failed.
>> Request: ?tap-start tap0 gbe3 192.168.3.16 60000 02:02:C0:A8:03:10
>> Reply: !tap-start fail.
>> FAILURE DETECTED. Log entries:
>> 192.168.100.2: Starting thread Thread-1
>> 192.168.100.2: #version poco-0.1
>> 192.168.100.2: #build-state poco-0.2804
>> 192.168.100.2: ?progdev tut2.bof
>>
>> 192.168.100.2: !progdev ok 528
>> 192.168.100.2: Programming FPGA with tut2.bof... ok.
>> 192.168.100.2: ?write pkt_sim_enable 0 \0\0\0\0
>>
>> 192.168.100.2: !write ok
>> 192.168.100.2: ?read pkt_sim_enable 0 4
>>
>> 192.168.100.2: !read ok \0\0\0\0
>> 192.168.100.2: Write 0 to register pkt_sim_enable at offset 0 ok.
>> 192.168.100.2: ?read gbe0_linkup 0 4
>>
>> 192.168.100.2: !read ok \0\0\0
>> 192.168.100.2: ?read gbe3_linkup 0 4
>>
>> 192.168.100.2: !read ok \0\0\0
>> 192.168.100.2: Starting tgtap driver instance for tap-start: tap0 gbe3
>> 192.168.3.16 60000 02:02:C0:A8:03:10
>> 192.168.100.2: ?tap-start tap0 gbe3 192.168.3.16 60000 02:02:C0:A8:03:10
>>
>> 192.168.100.2: #log error 2416053613647 poco register\_tap0\_seems\_
>> unavailable
>> 192.168.100.2: !tap-start fail
>> 192.168.100.2: Request tap-start failed.
>> Request: ?tap-start tap0 gbe3 192.168.3.16 60000 02:02:C0:A8:03:10
>> Reply: !tap-start fail.
>> None
>> rolando@rolando-MS-7815:~/codigo_ROACH/tut2$
>>
>>
>> How do I solve the problem?
>>
>> I will appreciate any comments ...
>>
>> Regards
>>
>> RP
>>
>>
>>
>>
