This is now in the main casper-astro repo ( github.com/casper-astro/mlib_devel) .
Thanks Tim! Jack On Thu, 6 Apr 2017 at 16:52 Jack Hickish <jackhick...@gmail.com> wrote: > I'm sure I remember merging Tim's code in the past. I've just got off a > flight and am a bit dazed and confused right now, but I'll check what's in > the main casper-astro repository tomorrow and update the r2 core if needed. > > Cheers > > > Jack > > On Thu, 6 Apr 2017, 15:48 Madden, Timothy J., <tmad...@aps.anl.gov> wrote: > >> Oliver >> >> The roach1 yellow block will not work on roach2 because it uses the >> older style PLLs not found on the V6 chip of R2. I made a new yellow block >> for mkid 4x and it works fine. It is here: >> >> >> https://github.com/argonnexraydetector/RoachFirmPy/tree/master/ANLYellowBlocks >> >> The iSE project to write the yellow block, whcih you don't need is >> >> https://github.com/argonnexraydetector/RoachFirmPy/tree/master/ANLYellowBlocks/mkid_dacadc_4x >> >> >> What you need are these two things: >> >> https://github.com/argonnexraydetector/RoachFirmPy/tree/master/ANLYellowBlocks/xps_base >> Whatever is in the pcores dir should be coped into YOUR pcores dir in >> your roach build library. >> >> The second thing goes in your xps library dir: There are dirs starting w/ >> @ and m files. Store this stuff in your xps_library dir. >> >> https://github.com/argonnexraydetector/RoachFirmPy/tree/master/ANLYellowBlocks/xps_library >> >> >> You will have to start up your matlab after doing this. You may have to >> open the simulink lib browser and refresh. you shoudl see the new yellow >> blocks in your simulink. >> >> I guess this should go into the casper lib. I don't know how to do that. >> >> Tim Madden >> Argonne Lab >> USA >> >> >> >> >> >> ------------------------------ >> *From:* Wang Jinqing [jqw...@shao.ac.cn] >> *Sent:* Wednesday, April 05, 2017 11:54 PM >> *To:* Casper Lists >> *Subject:* [casper] about adc_mkid_4x (ROACH2) >> >> Hi , >> I want to use adc_mkid_4x on my roach2 board. But I found there's no >> adc_mkid_4x in the xps_ROACH2_base. So I copied the folder of adc_mkid_4x >> from XPS_ROACH1_base . But I found after going casper_xps, the error >> appears like below. So my question is how to get the correct adc_mkid_4x >> pcore? >> >> >> ERROR:EDK - IPNAME: adc_mkid_4x_interface, INSTANCE: t3_1_adc_mkid_4x1 - >> not >> supported for architecture 'virtex6sx' - >> /home/oper/roach/t3_1/XPS_ROACH2_base/system.mhs line 267 >> >> Thanks for the helps. >> >> Best Regards. >> Oliver Wang >> >> >> >> -- >> You received this message because you are subscribed to the Google Groups >> "casper@lists.berkeley.edu" group. >> To unsubscribe from this group and stop receiving emails from it, send an >> email to casper+unsubscr...@lists.berkeley.edu. >> To post to this group, send email to casper@lists.berkeley.edu. >> >> -- >> You received this message because you are subscribed to the Google Groups >> "casper@lists.berkeley.edu" group. >> To unsubscribe from this group and stop receiving emails from it, send an >> email to casper+unsubscr...@lists.berkeley.edu. >> To post to this group, send email to casper@lists.berkeley.edu. >> > -- You received this message because you are subscribed to the Google Groups "casper@lists.berkeley.edu" group. To unsubscribe from this group and stop receiving emails from it, send an email to casper+unsubscr...@lists.berkeley.edu. To post to this group, send email to casper@lists.berkeley.edu.