On Tue, Mar 11, 2008 at 11:06 PM, Jarryd Beck <[EMAIL PROTECTED]> wrote: > > > > > > Also when I plugged it in, it sat there for about 10 seconds before > > > finishing loading (dmesg printed another 5 lines about the device > > > after about 10 seconds), but still no tuning. > > > > Can I see those five lines? ;-) > > > > While you're at it, you may as well include dmesg from the point that the > bridge driver loads and on. > > > > Here's dmesg from the point it starts up until it finishes printing stuff. > > usb 2-10: new high speed USB device using ehci_hcd and address 22 > usb 2-10: configuration #1 chosen from 1 choice > af9015_usb_probe: > af9015_identify_state: reply:01 > dvb-usb: found a 'Leadtek Winfast DTV Dongle Gold' in cold state, will > try to load a firmware > dvb-usb: downloading firmware from file 'dvb-usb-af9015.fw' > af9015_download_firmware: > dvb-usb: found a 'Leadtek Winfast DTV Dongle Gold' in warm state. > dvb-usb: will pass the complete MPEG2 transport stream to the software > demuxer. > DVB: registering new adapter (Leadtek Winfast DTV Dongle Gold) > af9015_eeprom_dump: > 00: 31 c2 bb 0b 00 00 00 00 13 04 29 60 00 02 01 02 > 10: 00 80 00 fa fa 10 40 ef 01 30 31 30 31 30 32 30 > 20: 35 30 35 30 30 30 30 31 ff ff ff ff ff ff ff ff > 30: 00 00 3a 01 00 08 02 00 cc 10 00 00 9c ff ff ff > 40: ff ff ff ff ff 08 02 00 1d 8d c4 04 82 ff ff ff > 50: ff ff ff ff ff 26 00 00 04 03 09 04 10 03 4c 00 > 60: 65 00 61 00 64 00 74 00 65 00 6b 00 30 03 57 00 > 70: 69 00 6e 00 46 00 61 00 73 00 74 00 20 00 44 00 > 80: 54 00 56 00 20 00 44 00 6f 00 6e 00 67 00 6c 00 > 90: 65 00 20 00 47 00 6f 00 6c 00 64 00 20 03 30 00 > a0: 31 00 30 00 31 00 30 00 31 00 30 00 31 00 30 00 > b0: 36 00 30 00 30 00 30 00 30 00 31 00 00 ff ff ff > c0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff > d0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff > e0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff > f0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff > af9015_read_config: xtal:2 set adc_clock:28000 > af9015_read_config: tuner id1:156 > af9015_read_config: spectral inversion:0 > af9015_set_gpios: > af9013: firmware version:4.95.0 > DVB: registering frontend 2 (Afatech AF9013 DVB-T)... > af9015_tuner_attach: > tda18271_tuner_attach: > tda18271 5-00c0: creating new instance > > TDA18271HD/C1 detected @ 5-00c0 > input: IR-receiver inside an USB DVB receiver as /class/input/input34 > dvb-usb: schedule remote query interval to 200 msecs. > dvb-usb: Leadtek Winfast DTV Dongle Gold successfully initialized and > connected. > af9015_init: > af9015_download_ir_table: > input: Leadtek WinFast DTV Dongle Gold as /class/input/input35 > input: USB HID v1.01 Keyboard [Leadtek WinFast DTV Dongle Gold] on > usb-0000:00:02.1-10 > > > > This is channel 7's entry in channels.conf: > 7 > Digital:177500000:INVERSION_AUTO:BANDWIDTH_7_MHZ:FEC_2_3:FEC_2_3:QAM_64:TRANSMISSION_MODE_8K:GUARD_INTERVAL_1_16:HIERARCHY_NONE:513:514:1312
Jarryd, I've analyzed the snoop that you've taken of the windows driver, and I conclude that the driver is basically doing exactly the same that the linux driver would do. The only thing that I cannot verify is whether or not the tda18211 uses the same table values as the tda18271c1. Based on the traffic in your snoop, it looks like the exact same algorithm is used, but based on a new set of tables -- I will not be able to confirm that without a tda18211 datasheet. The only thing that you can do is try the tda18271 driver and hopefully it will work. Have you tried to tune yet? There is a space in your channels.conf, "7 Digital" -- you may want to change that to something like, "7Digital" so that command line applications will work. Good Luck, Mike _______________________________________________ linux-dvb mailing list linux-dvb@linuxtv.org http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
