DVBSky T9580 is a dual tuner card with one DVB-T2/C tuner and one DVB-S2 tuner. 
It contains the following components:

- PCIe bridge: Conexant CX23885
- Demod for terrestrial/cable: Silicon Labs Si2168-A30
- Tuner for terrestrial/cable: Silicon Labs Si2158-A20
- Demod for sat: Montage DS3103
- Tuner for sat: Montage TS2022

This patch depends on Max Nibble's patch for m88ds3103 (see patchwork 25312: 
https://patchwork.linuxtv.org/patch/25312/ ).

3 firmwares are needed:
- Si2168-A30 demod and Si2158-A20 tuner: same as TechnoTrend CT2-4400, 
https://www.mail-archive.com/linux-media@vger.kernel.org/msg76944.html
- Montage DS3103 demod: same as PCTV 461e, Antti has it on his LinuxTV project 
page: http://palosaari.fi/linux/v4l-dvb/firmware/M88DS3103/

IR receiver is not supported.

Values in cx23885_gpio_setup, cx23885_card_setup and dvbsky_t9580_set_voltage 
as well as the EEPROM read function are taken from the manufacturer provided 
semi-open source driver. The drivers in question are Linux GPL'd media tree 
drivers for cx23885 modified by Max Nibble (nibble....@gmail.com) with 
proprietary tuner/demod drivers. Max is aware of this patch and has approved my 
use of the values in this patch.

Signed-off-by: Olli Salonen <olli.salo...@iki.fi>
---
 drivers/media/pci/cx23885/Kconfig         |   4 +
 drivers/media/pci/cx23885/cx23885-cards.c |  26 +++++
 drivers/media/pci/cx23885/cx23885-dvb.c   | 160 ++++++++++++++++++++++++++++++
 drivers/media/pci/cx23885/cx23885.h       |   1 +
 4 files changed, 191 insertions(+)

diff --git a/drivers/media/pci/cx23885/Kconfig 
b/drivers/media/pci/cx23885/Kconfig
index e12c006..413587e 100644
--- a/drivers/media/pci/cx23885/Kconfig
+++ b/drivers/media/pci/cx23885/Kconfig
@@ -32,12 +32,16 @@ config VIDEO_CX23885
        select DVB_A8293 if MEDIA_SUBDRV_AUTOSELECT
        select DVB_MB86A20S if MEDIA_SUBDRV_AUTOSELECT
        select DVB_SI2165 if MEDIA_SUBDRV_AUTOSELECT
+       select DVB_SI2168 if MEDIA_SUBDRV_AUTOSELECT
+       select DVB_M88DS3103 if MEDIA_SUBDRV_AUTOSELECT
        select MEDIA_TUNER_MT2063 if MEDIA_SUBDRV_AUTOSELECT
        select MEDIA_TUNER_MT2131 if MEDIA_SUBDRV_AUTOSELECT
        select MEDIA_TUNER_XC2028 if MEDIA_SUBDRV_AUTOSELECT
        select MEDIA_TUNER_TDA8290 if MEDIA_SUBDRV_AUTOSELECT
        select MEDIA_TUNER_TDA18271 if MEDIA_SUBDRV_AUTOSELECT
        select MEDIA_TUNER_XC5000 if MEDIA_SUBDRV_AUTOSELECT
+       select MEDIA_TUNER_SI2157 if MEDIA_SUBDRV_AUTOSELECT
+       select MEDIA_TUNER_M88TS2022 if MEDIA_SUBDRV_AUTOSELECT
        select DVB_TUNER_DIB0070 if MEDIA_SUBDRV_AUTOSELECT
        ---help---
          This is a video4linux driver for Conexant 23885 based
diff --git a/drivers/media/pci/cx23885/cx23885-cards.c 
b/drivers/media/pci/cx23885/cx23885-cards.c
index c2b6080..c1b02bb 100644
--- a/drivers/media/pci/cx23885/cx23885-cards.c
+++ b/drivers/media/pci/cx23885/cx23885-cards.c
@@ -679,6 +679,11 @@ struct cx23885_board cx23885_boards[] = {
                        .amux   = CX25840_AUDIO7,
                } },
        },
+       [CX23885_BOARD_DVBSKY_T9580] = {
+               .name           = "DVBSky T9580",
+               .portb          = CX23885_MPEG_DVB,
+               .portc          = CX23885_MPEG_DVB,
+       },
 };
 const unsigned int cx23885_bcount = ARRAY_SIZE(cx23885_boards);
 
@@ -934,6 +939,10 @@ struct cx23885_subid cx23885_subids[] = {
                .subvendor = 0x18ac,
                .subdevice = 0xdb98,
                .card      = CX23885_BOARD_DVICO_FUSIONHDTV_DVB_T_DUAL_EXP2,
+       }, {
+               .subvendor = 0x4254,
+               .subdevice = 0x9580,
+               .card      = CX23885_BOARD_DVBSKY_T9580,
        },
 };
 const unsigned int cx23885_idcount = ARRAY_SIZE(cx23885_subids);
@@ -1528,6 +1537,14 @@ void cx23885_gpio_setup(struct cx23885_dev *dev)
                cx_set(GP0_IO, 0x00040004);
                mdelay(60);
                break;
+       case CX23885_BOARD_DVBSKY_T9580:
+               /* enable GPIO3-18 pins */
+               cx_write(MC417_CTL, 0x00000037);
+               cx23885_gpio_enable(dev, GPIO_2 | GPIO_11, 1);
+               cx23885_gpio_clear(dev, GPIO_2 | GPIO_11);
+               mdelay(100);
+               cx23885_gpio_set(dev, GPIO_2 | GPIO_11);
+               break;
        }
 }
 
@@ -1851,6 +1868,14 @@ void cx23885_card_setup(struct cx23885_dev *dev)
                ts2->ts_clk_en_val = 0x1; /* Enable TS_CLK */
                ts2->src_sel_val   = CX23885_SRC_SEL_PARALLEL_MPEG_VIDEO;
                break;
+       case CX23885_BOARD_DVBSKY_T9580:
+               ts1->gen_ctrl_val  = 0x5; /* Parallel */
+               ts1->ts_clk_en_val = 0x1; /* Enable TS_CLK */
+               ts1->src_sel_val   = CX23885_SRC_SEL_PARALLEL_MPEG_VIDEO;
+               ts2->gen_ctrl_val  = 0x8; /* Serial bus */
+               ts2->ts_clk_en_val = 0x1; /* Enable TS_CLK */
+               ts2->src_sel_val   = CX23885_SRC_SEL_PARALLEL_MPEG_VIDEO;
+               break;
        case CX23885_BOARD_HAUPPAUGE_HVR1250:
        case CX23885_BOARD_HAUPPAUGE_HVR1500:
        case CX23885_BOARD_HAUPPAUGE_HVR1500Q:
@@ -1913,6 +1938,7 @@ void cx23885_card_setup(struct cx23885_dev *dev)
        case CX23885_BOARD_AVERMEDIA_HC81R:
        case CX23885_BOARD_TBS_6980:
        case CX23885_BOARD_TBS_6981:
+       case CX23885_BOARD_DVBSKY_T9580:
                dev->sd_cx25840 = v4l2_i2c_new_subdev(&dev->v4l2_dev,
                                &dev->i2c_bus[2].i2c_adap,
                                "cx25840", 0x88 >> 1, NULL);
diff --git a/drivers/media/pci/cx23885/cx23885-dvb.c 
b/drivers/media/pci/cx23885/cx23885-dvb.c
index 2608155..1e9e041 100644
--- a/drivers/media/pci/cx23885/cx23885-dvb.c
+++ b/drivers/media/pci/cx23885/cx23885-dvb.c
@@ -73,6 +73,10 @@
 #include "a8293.h"
 #include "mb86a20s.h"
 #include "si2165.h"
+#include "si2168.h"
+#include "si2157.h"
+#include "m88ds3103.h"
+#include "m88ts2022.h"
 
 static unsigned int debug;
 
@@ -551,6 +555,35 @@ static int p8000_set_voltage(struct dvb_frontend *fe, 
fe_sec_voltage_t voltage)
        return 0;
 }
 
+static int dvbsky_t9580_set_voltage(struct dvb_frontend *fe,
+                                       fe_sec_voltage_t voltage)
+{
+       struct cx23885_tsport *port = fe->dvb->priv;
+       struct cx23885_dev *dev = port->dev;
+
+       cx23885_gpio_enable(dev, GPIO_0 | GPIO_1, 1);
+
+       switch (voltage) {
+       case SEC_VOLTAGE_13:
+               cx23885_gpio_set(dev, GPIO_1);
+               cx23885_gpio_clear(dev, GPIO_0);
+               break;
+       case SEC_VOLTAGE_18:
+               cx23885_gpio_set(dev, GPIO_1);
+               cx23885_gpio_set(dev, GPIO_0);
+               break;
+       case SEC_VOLTAGE_OFF:
+               cx23885_gpio_clear(dev, GPIO_1);
+               cx23885_gpio_clear(dev, GPIO_0);
+               break;
+       }
+
+       /* call the frontend set_voltage function */
+       port->fe_set_voltage(fe, voltage);
+
+       return 0;
+}
+
 static int cx23885_dvb_set_frontend(struct dvb_frontend *fe)
 {
        struct dtv_frontend_properties *p = &fe->dtv_property_cache;
@@ -715,6 +748,19 @@ static const struct si2165_config 
hauppauge_hvr4400_si2165_config = {
        .ref_freq_Hz    = 16000000,
 };
 
+static const struct m88ds3103_config dvbsky_t9580_m88ds3103_config = {
+       .i2c_addr = 0x68,
+       .clock = 27000000,
+       .i2c_wr_max = 33,
+       .clock_out = 0,
+       .ts_mode = M88DS3103_TS_PARALLEL,
+       .ts_clk = 16000,
+       .ts_clk_pol = 1,
+       .lnb_en_pol = 1,
+       .lnb_hv_pol = 0,
+       .agc = 0x99,
+};
+
 static int netup_altera_fpga_rw(void *device, int flag, int data, int read)
 {
        struct cx23885_dev *dev = (struct cx23885_dev *)device;
@@ -864,6 +910,13 @@ static int dvb_register(struct cx23885_tsport *port)
        struct cx23885_dev *dev = port->dev;
        struct cx23885_i2c *i2c_bus = NULL, *i2c_bus2 = NULL;
        struct videobuf_dvb_frontend *fe0, *fe1 = NULL;
+       struct si2168_config si2168_config;
+       struct si2157_config si2157_config;
+       struct m88ts2022_config m88ts2022_config;
+       struct i2c_board_info info;
+       struct i2c_adapter *adapter;
+       struct i2c_client *client_demod;
+       struct i2c_client *client_tuner;
        int mfe_shared = 0; /* bus not shared by default */
        int ret;
 
@@ -1501,6 +1554,97 @@ static int dvb_register(struct cx23885_tsport *port)
                        break;
                }
                break;
+       case CX23885_BOARD_DVBSKY_T9580:
+               i2c_bus = &dev->i2c_bus[0];
+               i2c_bus2 = &dev->i2c_bus[1];
+               switch (port->nr) {
+               /* port b - satellite */
+               case 1:
+                       /* attach frontend */
+                       fe0->dvb.frontend = dvb_attach(m88ds3103_attach,
+                                       &dvbsky_t9580_m88ds3103_config,
+                                       &i2c_bus2->i2c_adap, &adapter);
+                       if (fe0->dvb.frontend == NULL)
+                               break;
+
+                       /* attach tuner */
+                       m88ts2022_config.fe = fe0->dvb.frontend;
+                       m88ts2022_config.clock = 27000000;
+                       memset(&info, 0, sizeof(struct i2c_board_info));
+                       strlcpy(info.type, "m88ts2022", I2C_NAME_SIZE);
+                       info.addr = 0x60;
+                       info.platform_data = &m88ts2022_config;
+                       request_module(info.type);
+                       client_tuner = i2c_new_device(adapter, &info);
+                       if (client_tuner == NULL ||
+                                       client_tuner->dev.driver == NULL)
+                               goto frontend_detach;
+                       if (!try_module_get(client_tuner->dev.driver->owner)) {
+                               i2c_unregister_device(client_tuner);
+                               goto frontend_detach;
+                       }
+
+                       /* delegate signal strength measurement to tuner */
+                       fe0->dvb.frontend->ops.read_signal_strength =
+                               
fe0->dvb.frontend->ops.tuner_ops.get_rf_strength;
+
+                       /*
+                        * for setting the voltage we need to set GPIOs on
+                        * the card.
+                        */
+                       port->fe_set_voltage =
+                               fe0->dvb.frontend->ops.set_voltage;
+                       fe0->dvb.frontend->ops.set_voltage =
+                               dvbsky_t9580_set_voltage;
+
+                       port->i2c_client_tuner = client_tuner;
+
+                       break;
+               /* port c - terrestrial/cable */
+               case 2:
+                       /* attach frontend */
+                       si2168_config.i2c_adapter = &adapter;
+                       si2168_config.fe = &fe0->dvb.frontend;
+                       si2168_config.ts_mode = SI2168_TS_SERIAL;
+                       memset(&info, 0, sizeof(struct i2c_board_info));
+                       strlcpy(info.type, "si2168", I2C_NAME_SIZE);
+                       info.addr = 0x64;
+                       info.platform_data = &si2168_config;
+                       request_module(info.type);
+                       client_demod = i2c_new_device(&i2c_bus->i2c_adap, 
&info);
+                       if (client_demod == NULL ||
+                                       client_demod->dev.driver == NULL)
+                               goto frontend_detach;
+                       if (!try_module_get(client_demod->dev.driver->owner)) {
+                               i2c_unregister_device(client_demod);
+                               goto frontend_detach;
+                       }
+                       port->i2c_client_demod = client_demod;
+
+                       /* attach tuner */
+                       si2157_config.fe = fe0->dvb.frontend;
+                       memset(&info, 0, sizeof(struct i2c_board_info));
+                       strlcpy(info.type, "si2157", I2C_NAME_SIZE);
+                       info.addr = 0x60;
+                       info.platform_data = &si2157_config;
+                       request_module(info.type);
+                       client_tuner = i2c_new_device(adapter, &info);
+                       if (client_tuner == NULL ||
+                                       client_tuner->dev.driver == NULL) {
+                               module_put(client_demod->dev.driver->owner);
+                               i2c_unregister_device(client_demod);
+                               goto frontend_detach;
+                       }
+                       if (!try_module_get(client_tuner->dev.driver->owner)) {
+                               i2c_unregister_device(client_tuner);
+                               module_put(client_demod->dev.driver->owner);
+                               i2c_unregister_device(client_demod);
+                               goto frontend_detach;
+                       }
+                       port->i2c_client_tuner = client_tuner;
+                       break;
+               }
+               break;
        default:
                printk(KERN_INFO "%s: The frontend of your DVB/ATSC card "
                        " isn't supported yet\n",
@@ -1575,6 +1719,22 @@ static int dvb_register(struct cx23885_tsport *port)
                memcpy(port->frontends.adapter.proposed_mac, eeprom + 0xa0, 6);
                break;
                }
+       case CX23885_BOARD_DVBSKY_T9580: {
+               u8 eeprom[256]; /* 24C02 i2c eeprom */
+
+               if (port->nr > 2)
+                       break;
+
+               /* Read entire EEPROM */
+               dev->i2c_bus[0].i2c_client.addr = 0xa0 >> 1;
+               tveeprom_read(&dev->i2c_bus[0].i2c_client, eeprom,
+                               sizeof(eeprom));
+               printk(KERN_INFO "DVBSky T9580 port %d MAC address: %pM\n",
+                       port->nr, eeprom + 0xc0 + (port->nr-1) * 8);
+               memcpy(port->frontends.adapter.proposed_mac, eeprom + 0xc0 +
+                       (port->nr-1) * 8, 6);
+               break;
+               }
        }
 
        return ret;
diff --git a/drivers/media/pci/cx23885/cx23885.h 
b/drivers/media/pci/cx23885/cx23885.h
index e60ff7f..f9a23b6 100644
--- a/drivers/media/pci/cx23885/cx23885.h
+++ b/drivers/media/pci/cx23885/cx23885.h
@@ -98,6 +98,7 @@
 #define CX23885_BOARD_LEADTEK_WINFAST_PXPVR2200 42
 #define CX23885_BOARD_HAUPPAUGE_IMPACTVCBE     43
 #define CX23885_BOARD_DVICO_FUSIONHDTV_DVB_T_DUAL_EXP2 44
+#define CX23885_BOARD_DVBSKY_T9580             45
 
 #define GPIO_0 0x00000001
 #define GPIO_1 0x00000002
-- 
1.9.1

--
To unsubscribe from this list: send the line "unsubscribe linux-media" in
the body of a message to majord...@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Reply via email to