Luca Montecchiani
Mon, 8 Nov 1999 05:17:38 -0800
Hi! I've just successfully burn a 600M cdrom with 2.3.26+"new patch" applied ;) The bad news is that I have to change my cmdline from aha152x=0x140,9,7 to aha152x=0x140,9,7,1,1,0 The new driver go for synchronous=enabled by default , but with this option I got a lot of warning ( see below ) and my Yamaha wasn't recognized. from README.aha152x -SYNCHRONOUS enable synchronous transfers (0/1; default 0 [off]) +SYNCHRONOUS enable synchronous transfers (0/1; default 1 [on]) Follow good kernel boot messages (synchronous=disabled): -------------------------------------------------------- aha152x: processing commandline: ok aha152x: BIOS test: passed, detected 1 controller(s) aha152x0: vital data: io=0x140 (0x140/0x140), irq=9, scsiid=7, reconnect=enabled, parity=enabled, synchronous=disabled, delay=100, extended translation=disabled aha152x: trying software interrupt, ok. scsi0 : Adaptec 152x SCSI driver; $Revision: 1.20 $ scsi : 1 host. Vendor: YAMAHA Model: CRW4260 Rev: 1.0h Type: CD-ROM ANSI SCSI revision: 02 Detected scsi CD-ROM sr0 at scsi0, channel 0, id 3, lun 0 scsi : detected 1 SCSI cdrom total. sr0: scsi3-mmc drive: 6x/6x writer cd/rw xa/form2 cdda tray Follow bad kernel boot messages (synchronous=enabled): ------------------------------------------------------ aha152x: processing commandline: ok aha152x: BIOS test: passed, detected 1 controller(s) aha152x0: vital data: io=0x140 (0x140/0x140), irq=9, scsiid=7, reconnect=enabled, parity=enabled, synchronous=enabled, delay=100, extended translation=disabled aha152x: trying software interrupt, ok. scsi0 : Adaptec 152x SCSI driver; $Revision: 1.20 $ scsi : 1 host. aha152x: sending Synchronous Data Transfer Request period = 200 ns, offset = 8 aha152x: SDTR was rejected scsi0 : channel 0 target 3 lun 0 request sense failed, performing reset. SCSI bus is being reset for host 0 channel 0. scsi : aborting command due to timeout : pid 3, scsi0, channel 0, id 3, lun 0 Test Unit Ready 00 00 00 00 00 aha152x: abort(), SCpnt=0xc02e2e00, QUEUE STATUS: issue_SC: 0xc02e2e00: target=3; lun=0; cmnd=(Test Unit Ready 00 00 00 00 00 ); resid=0; residual=0; buffers=0; phase |not issued|; next=0x00000000 current_SC: none disconnected_SC: waiting: SCSISEQ (); SCSISIG (DATA OUT); INTSTAT (hi); SSTAT (BUSFREE ); SSTAT (BUSFREE ); SXFRCTL0 (CH1 ); SIGNAL (); SELID (00), STCNT (0), SSTAT2 (SEMPTY ); SFCNT (0); SCSICNT (0), OFFCNT(0), SSTAT4 (); DMACNTRL0 (16BIT PIO READ ); DMASTAT (DFIFOEMP ) enabled interrupts (ENBUSFREE ) scsi : aborting command due to timeout : pid 3, scsi0, channel 0, id 3, lun 0 Test Unit Ready 00 00 00 00 00 aha152x: abort(), SCpnt=0xc02e2e00, QUEUE STATUS: issue_SC: 0xc02e2e00: target=3; lun=0; cmnd=(Test Unit Ready 00 00 00 00 00 ); resid=0; residual=0; buffers=0; phase |not issued|; next=0x00000000 current_SC: none disconnected_SC: waiting: SCSISEQ (); SCSISIG (DATA OUT); INTSTAT (hi); SSTAT (BUSFREE ); SSTAT (BUSFREE ); SXFRCTL0 (CH1 ); SIGNAL (); SELID (00), STCNT (0), SSTAT2 (SEMPTY ); SFCNT (0); SCSICNT (0), OFFCNT(0), SSTAT4 (); DMACNTRL0 (16BIT PIO READ ); DMASTAT (DFIFOEMP ) enabled interrupts (ENBUSFREE ) scsi : aborting command due to timeout : pid 4, scsi0, channel 0, id 4, lun 0 Test Unit Ready 00 00 00 00 00 aha152x: abort(), SCpnt=0xc02e2e00, QUEUE STATUS: issue_SC: 0xc02e2e00: target=4; lun=0; cmnd=(Test Unit Ready 00 00 00 00 00 ); resid=0; residual=0; buffers=0; phase |not issued|; next=0x00000000 current_SC: none disconnected_SC: waiting: SCSISEQ (); SCSISIG (DATA OUT); INTSTAT (hi); SSTAT (BUSFREE ); SSTAT (BUSFREE ); SXFRCTL0 (CH1 ); SIGNAL (); SELID (00), STCNT (0), SSTAT2 (SEMPTY ); SFCNT (0); SCSICNT (0), OFFCNT(0), SSTAT4 (); DMACNTRL0 (16BIT PIO READ ); DMASTAT (DFIFOEMP ) enabled interrupts (ENBUSFREE ) scsi : aborting command due to timeout : pid 4, scsi0, channel 0, id 4, lun 0 Test Unit Ready 00 00 00 00 00 aha152x: abort(), SCpnt=0xc02e2e00, QUEUE STATUS: issue_SC: 0xc02e2e00: target=4; lun=0; cmnd=(Test Unit Ready 00 00 00 00 00 ); resid=0; residual=0; buffers=0; phase |not issued|; next=0x00000000 current_SC: none disconnected_SC: waiting: SCSISEQ (); SCSISIG (DATA OUT); INTSTAT (hi); SSTAT (BUSFREE ); SSTAT (BUSFREE ); SXFRCTL0 (CH1 ); SIGNAL (); SELID (00), STCNT (0), SSTAT2 (SEMPTY ); SFCNT (0); SCSICNT (0), OFFCNT(0), SSTAT4 (); DMACNTRL0 (16BIT PIO READ ); DMASTAT (DFIFOEMP ) enabled interrupts (ENBUSFREE ) scsi : aborting command due to timeout : pid 5, scsi0, channel 0, id 5, lun 0 Test Unit Ready 00 00 00 00 00 aha152x: abort(), SCpnt=0xc02e2e00, QUEUE STATUS: issue_SC: 0xc02e2e00: target=5; lun=0; cmnd=(Test Unit Ready 00 00 00 00 00 ); resid=0; residual=0; buffers=0; phase |not issued|; next=0x00000000 current_SC: none disconnected_SC: waiting: SCSISEQ (); SCSISIG (DATA OUT); INTSTAT (hi); SSTAT (BUSFREE ); SSTAT (BUSFREE ); SXFRCTL0 (CH1 ); SIGNAL (); SELID (00), STCNT (0), SSTAT2 (SEMPTY ); SFCNT (0); SCSICNT (0), OFFCNT(0), SSTAT4 (); DMACNTRL0 (16BIT PIO READ ); DMASTAT (DFIFOEMP ) enabled interrupts (ENBUSFREE ) scsi : aborting command due to timeout : pid 5, scsi0, channel 0, id 5, lun 0 Test Unit Ready 00 00 00 00 00 aha152x: abort(), SCpnt=0xc02e2e00, QUEUE STATUS: issue_SC: 0xc02e2e00: target=5; lun=0; cmnd=(Test Unit Ready 00 00 00 00 00 ); resid=0; residual=0; buffers=0; phase |not issued|; next=0x00000000 current_SC: none disconnected_SC: waiting: SCSISEQ (); SCSISIG (DATA OUT); INTSTAT (hi); SSTAT (BUSFREE ); SSTAT (BUSFREE ); SXFRCTL0 (CH1 ); SIGNAL (); SELID (00), STCNT (0), SSTAT2 (SEMPTY ); SFCNT (0); SCSICNT (0), OFFCNT(0), SSTAT4 (); DMACNTRL0 (16BIT PIO READ ); DMASTAT (DFIFOEMP ) enabled interrupts (ENBUSFREE ) scsi : aborting command due to timeout : pid 6, scsi0, channel 0, id 6, lun 0 Test Unit Ready 00 00 00 00 00 aha152x: abort(), SCpnt=0xc02e2e00, QUEUE STATUS: issue_SC: 0xc02e2e00: target=6; lun=0; cmnd=(Test Unit Ready 00 00 00 00 00 ); resid=0; residual=0; buffers=0; phase |not issued|; next=0x00000000 current_SC: none disconnected_SC: waiting: SCSISEQ (); SCSISIG (DATA OUT); INTSTAT (hi); SSTAT (BUSFREE ); SSTAT (BUSFREE ); SXFRCTL0 (CH1 ); SIGNAL (); SELID (00), STCNT (0), SSTAT2 (SEMPTY ); SFCNT (0); SCSICNT (0), OFFCNT(0), SSTAT4 (); DMACNTRL0 (16BIT PIO READ ); DMASTAT (DFIFOEMP ) enabled interrupts (ENBUSFREE ) scsi : aborting command due to timeout : pid 6, scsi0, channel 0, id 6, lun 0 Test Unit Ready 00 00 00 00 00 aha152x: abort(), SCpnt=0xc02e2e00, QUEUE STATUS: issue_SC: 0xc02e2e00: target=6; lun=0; cmnd=(Test Unit Ready 00 00 00 00 00 ); resid=0; residual=0; buffers=0; phase |not issued|; next=0x00000000 current_SC: none disconnected_SC: waiting: SCSISEQ (); SCSISIG (DATA OUT); INTSTAT (hi); SSTAT (BUSFREE ); SSTAT (BUSFREE ); SXFRCTL0 (CH1 ); SIGNAL (); SELID (00), STCNT (0), SSTAT2 (SEMPTY ); SFCNT (0); SCSICNT (0), OFFCNT(0), SSTAT4 (); DMACNTRL0 (16BIT PIO READ ); DMASTAT (DFIFOEMP ) enabled interrupts (ENBUSFREE ) scsi : detected total. PPP generic driver version 2.4.0 PPP Deflate compression module registered SLIP: version 0.8.4-NET3.019-NEWTTY (dynamic channels, max=256). thanks, luca -- ------------------------------------------------------------------ E-mail......: Luca Montecchiani <[EMAIL PROTECTED]> W.W.W.......: http://i.am/m.luca - http://luca.myip.org Speakfreely.: sflwl -hlwl.fourmilab.ch luca@ I.C.Q.......: 17655604 -----------------------=(Linux since 1995)=----------------------- Non esiste vento favorevole per il marinaio che non sa dove andare Seneca - To unsubscribe from this list: send the line "unsubscribe linux-scsi" in the body of a message to [EMAIL PROTECTED]