Hi, On 24.04.2017 15:41, Pedro Lafuente wrote: > commit 862120ca23a0be3f865c3b566a8d50e9c55f3517 > Author: pedro.lafue...@avt-stoye.de <pedro.lafue...@avt-stoye.de>
Minor cosmetics, but you probably want to set user.name to your name, not your e-mail address, in your ~/.gitconfig. After that, git commit --amend --reset-author should correct this. > Date: Mon Apr 24 15:20:31 2017 +0200 > > SWupdate package support for ptxdist. > > diff --git a/rules/swupdate.in b/rules/swupdate.in > new file mode 100644 > index 0000000..43517b6 > --- /dev/null > +++ b/rules/swupdate.in > @@ -0,0 +1,618 @@ > +## SECTION=applications > + > +menuconfig SWUPDATE > +bool > +prompt "SWupdate" This could benefit from a "help" option, to give the users a hint what the package is about :-) > + > +if SWUPDATE > + > +menu "Swupdate Settings" > + > +menu "General Configuration" > + > +config SCRIPTS All of these config options also need the SWUPDATE_ prefix for correct namespacing. Otherwise it could lead to problems when a different package defines a config option with the same name. (Also see my note further below.) > + bool "enable pre and postinstall scripts" > + default y > + help > + Enabling this option, the installer will run > + pre- and postinstall scripts, if they are present > + in the image. For security reason, this option > + can be switched off. > + > +config HW_COMPATIBILITY > + bool "check for hardware / software compatibility" > + default n > + help > + If enabled, check if the hardware revision > + supports the software version. Detecting the hardware > + revision is very board specific, and it cannot be generalized. > + For this reason, the software expects that the detected > + version is written into a file by a previous software. > + > +config HW_COMPATIBILITY_FILE > + string "File with detected hardware revisions" > + depends on HW_COMPATIBILITY > + default "/etc/hwrevision" > + help > + File where to read the detected hardware revsion > + that must be compared with the software version. > + The file has simple entries (one per line) in the > + format of "major.minor". > + > +config SW_VERSIONS_FILE > + string "File with detected software version" > + default "/etc/sw-versions" > + help > + This is an optional file that is scanned at the > + beginning to read the installed versions of > + all sw-components. Each entry in the file is a > + a pair of "name version". > + In sw-description, an image can have the > + optional attributes: > + "name" : key for searching in SW_VERSIONS_FILE > + "version" : version contained in the .swu > + "install-if-different" : if set, version > + is compared with the one in SW_VERSIONS_FILE. > + The image is installed only if there is a version mismatch. > + This lets reduce risks in case of components that are not > + safe to be updated, such as the bootloader. Updating it is a risk, > + but in some cases it can be required to do it. Having a check, > + the risky-component is not always updated. > + > +config MTD > + bool "MTD support" > + default y > + #depends on HAVE_LIBMTD Is there a reason this is commented out? > + select MTD_UTILS > + help > + Enable MTD support. > + > +config SWUPDATE_LUA > + bool "lua" > + default y > + #depends on HAVE_LUA > + select LUA > + select LUA_INSTALL_LUA ...like here. You see that the LUA_ prefix also makes it possible to depend on sub-features of other packages. - Roland > + select LUA_INSTALL_LUAC > + select LUA_INSTALL_LIBLUA > + > + help > + Enable LUA interpreter. > + > +#config LUAPKG > +# string "LUA pkg-config name" > +# default "lua" > +# #depends on LUA > +# select LUA > +# select LUA_INSTALL_LUA > +# select LUA_INSTALL_LUAC > +# select LUA_INSTALL_LIBLUA > +# help > +# Which pkg-config package supplies the Lua API. > + > +# These are auto-selected by other options > + > +config FEATURE_SYSLOG > + bool #No description makes it a hidden option > + default n > + #help > + # This option is auto-selected when you select any applet which may > + # send its output to syslog. You do not need to select it manually. > + > +endmenu > + > +menu 'Build Options' > + > +config STATIC > + bool "Build swupdate as a static binary (no shared libs)" > + default n > + help > + If you want to build a static swupdate binary, which does not > + use or require any shared libraries, then enable this option. > + This can cause swupdate to be considerably larger, so you should > + leave this option false unless you have a good reason (i.e. > + your target platform does not support shared libraries, or > + you are building an initrd which doesn't need anything but > + swupdate, etc). > + > + Most people will leave this set to 'N'. > + > +config CROSS_COMPILE > + string "Cross Compiler prefix" > + default > "/opt/OSELAS.Toolchain-2014.12.2/arm-cortexa8-linux-gnueabihf/gcc-4.9.2-glibc-2.20-binutils-2.24-kernel-3.16-sanitized/bin/arm-cortexa8-linux-gnueabihf-" > > + help > + If you want to build swupdate with a cross compiler, then you > + will need to set this to the cross-compiler prefix, for example, > + "i386-uclibc-". > + > + Native builds leave this empty. > + > +config SYSROOT > + string "Path to sysroot" > + default > "/opt/OSELAS.Toolchain-2014.12.2/arm-cortexa8-linux-gnueabihf/gcc-4.9.2-glibc-2.20-binutils-2.24-kernel-3.16-sanitized/sysroot-arm-cortexa8-linux-gnueabihf" > > + help > + If you want to build swupdate with a cross compiler, then you > + might also need to specify where /usr/include and /usr/lib > + will be found. > + > + For example, swupdate can be built against an installed > + Android NDK, platform version 9, for ARM ABI with > + > + CONFIG_SYSROOT=/opt/android-ndk/platforms/android-9/arch-arm > + > + Native builds leave this empty. > + > +config EXTRA_CFLAGS > + string "Additional CFLAGS" > + default "" > + help > + Additional CFLAGS to pass to the compiler verbatim. > + > +config EXTRA_LDFLAGS > + string "Additional LDFLAGS" > + default "" > + help > + Additional LDFLAGS to pass to the linker verbatim. > + > +config EXTRA_LDLIBS > + string "Additional LDLIBS" > + default "" > + help > + Additional LDLIBS to pass to the linker with -l. > + > +endmenu > + > +menu 'Debugging Options' > + > +config SW_UPDATE_DEBUG > + bool "Build Swupdate with extra Debugging symbols" > + default n > + help > + Say Y here if you wish to examine swupdate internals while > applets are > + running. This increases the size of the binary considerably, and > + should only be used when doing development. If you are doing > + development and want to debug swupdate, answer Y. > + > + Most people should answer N. > + > +config DEBUG_PESSIMIZE > + bool "Disable compiler optimizations" > + default n > + depends on SW_UPDATE_DEBUG > + help > + The compiler's optimization of source code can eliminate and reorder > + code, resulting in an executable that's hard to understand when > + stepping through it with a debugger. This switches it off, resulting > + in a much bigger executable that more closely matches the source > + code. > + > +config WERROR > + bool "Abort compilation on any warning" > + default n > + help > + Selecting this will add -Werror to gcc command line. > + > + Most people should answer N. > + > +config NOCLEANUP > + bool "Do not remove temporary files after execution" > + default n > + help > + After each run, temporary files are removed from > + /tmp to restart in a clean state. For debugging purpose, > + it helps to check the consistency of the file extracted > + by swupdate. > + For production, answer N. > + > +endmenu > +endmenu > + > +config DOWNLOAD > + bool "Enable image downloading" > + default y > + select LIBCURL > + help > + Enable update from image URL using libcurl. Files are downloaded > + completely before installation begins. > + > +config HASH_VERIFY > + bool "Allow to add sha256 hash to each image" > + select OPENSSL > + default y > + help > + Allow to add a sha256 hash to an artifact. > + This is automatically set in case of Signed Image > + > +config SIGNED_IMAGES > + bool "Enable verification of signed images" > + default y > + select OPENSSL > + select HASH_VERIFY > + > +config ENCRYPTED_IMAGES > + bool "Images can be encrypted with a symmetric key" > + select OPENSSL > + > + # DO NOT EDIT. This file is generated from Config.src > + # > + # For a description of the syntax of this configuration file, > + # see scripts/kbuild/config-language.txt. > + # > + > +# menu "Suricatta" > +# menu "Features" > +# depends on SURICATTA > +# config SURICATTA_SSL > +# bool "SSL support" > +# default n > +# #depends on HAVE_LIBSSL > +# #depends on HAVE_LIBCRYPTO > +# select OPENSSL > + > +# help > +# Enable SSL and checksum verification support in > suricatta. > + > +# choice > +# prompt "Update Status Storage" > +# default SURICATTA_STATE_CHOICE_UBOOT if UBOOT > +# default SURICATTA_STATE_CHOICE_NONE if !UBOOT > +# help > +# Place for suricatta to persistently store the update > +# status for, e.g., communicating it to the server after > +# a reboot. > + > +# config SURICATTA_STATE_CHOICE_NONE > +# bool "None" > +# help > +# Do not store update status. > + > +# config SURICATTA_STATE_CHOICE_UBOOT > +# bool "U-Boot" > +# #depends on UBOOT > +# #depends on HAVE_ZLIB > +# select U_BOOT_TOOLS_TOOL_ENV > +# select U_BOOT_TOOLS > +# select ZLIB > +# help > +# Store update status in U-Boot's environment. > +# Specify U-Boot environment variable name to store > update status in. > + > +# endchoice > + > +# config SURICATTA_STATE_UBOOT > +# string "Store Update Status in U-Boot Environment variable" > +# default "ustate" > +# depends on SURICATTA_STATE_CHOICE_UBOOT > +# help > +# Store update information in U-Boot's environment. > + > +# endmenu > + > +# menu "Server" > +# choice > +# prompt "Server Type" > +# default SURICATTA_HAWKBIT > +# help > +# Choose the server type. Currently, just hawkBit is > +# supported. > + > +# config SURICATTA_HAWKBIT > +# bool "hawkBit support" > +# #depends on HAVE_LIBCURL > +# #depends on JSON > +# select JSON_C > +# select JSON_GLIB > +# select LIBFASTJSON > +# select LIBCURL > +# select SURICATTA > +# help > +# Support for hawkBit server. > +# https://projects.eclipse.org/projects/iot.hawkbit > + > +# config SURICATTA_SERVER_NONE > +# bool "None" > +# help > +# Do not start suricatta mode > +# endchoice > +# endmenu > +# endmenu > + > + config WEBSERVER > + bool "Enable webserver" > + default y > + help > + Enable update from remote using a webserver on the target. > + > + menu "Webserver Features" > + config MONGOOSE > + bool "mongoose" > + default y > + help > + Enable mongoose webserver. > + > + menu "Mongoose Feature" > + depends on MONGOOSE > + > + config MONGOOSELUA > + bool "lua interpreter" > + #depends on LUA > + select LUA > + select LUA_INSTALL_LUA > + select LUA_INSTALL_LUAC > + select LUA_INSTALL_LIBLUA > + default y > + help > + It allows to use LUA scripts as CGI interpreter. > + > + config MONGOOSEIPV6 > + bool "ipv6" > + default y > + help > + It enables ipv6 support into mongoose > + > + config MONGOOSESSL > + bool "ssl" > + #depends on HAVE_LIBSSL > + #depends on HAVE_LIBCRYPTO > + select OPENSSL > + help > + It enables SSL support into mongoose > + endmenu > + endmenu > + > +menu "Archival Features" > + > +config GUNZIP > + bool "gunzip" > + default y > + select ZLIB > + help > + gunzip is used to decompress archives created by gzip. > + You can use the `-t' option to test the integrity of > + an archive, without decompressing it. > + > +endmenu > + > +menu "Parser Features" > + > +config SWUPDATE_LIBCONFIG > + bool "libconfig" > + default y > + #depends on HAVE_LIBCONFIG > + select LIBCONFIG > + select LIBCONFIG_CXX > + help > + Use libconfig to parse the configuration file. > + This is the default parser. > + > +config LIBCONFIGROOT > + string > + prompt "Name of root node" > + depends on SWUPDATE_LIBCONFIG > + > + > + help > + For compatibility reasons, the root node > + can be set to something else as "software". > + In most case you do not need to set it. > + > +config JSON > + bool "libjson" > + default n > + #depends on HAVE_JSON_C > + select JSON_C > + > + help > + Use json-c to parse the configuration file. > + Also required for suricatta's hawkBit Server support. > + > + > +config LUAEXTERNAL > + bool "lua" > + #depends on LUA > + select LUA > + select LUA_INSTALL_LUA > + select LUA_INSTALL_LUAC > + select LUA_INSTALL_LIBLUA > + default n > + help > + call an external parser written in LUA. > + > +config SETEXTPARSERNAME > + bool "Set external parser name" > + depends on LUAEXTERNAL > + default n > + help > + Set to define own path and filename for the > + external parser, else default lua-tools/extparser.lua > + will be used. > + > +config EXTPARSERNAME > + string "External parser file name" > + depends on SETEXTPARSERNAME > + help > + Lua script to be executed for parsing > + the sw-description file. > + > +config SETSWDESCRIPTION > + bool "set file description name" > + default n > + help > + Set it if you want to change the name of > + the default software descritpion file. > + If not set, default file name is "sw-description" > + > +config SWDESCRIPTION > + string "description file" > + depends on SETSWDESCRIPTION > + help > + File extracted from the image containing > + the description (meta) of the images. > + This file, after extraction, is passed to the parser. > +endmenu > + > +# > +# For a description of the syntax of this configuration file, > +# see scripts/kbuild/config-language.txt. > +# > + > +menu "Image Handlers" > + > +config SWUPDATE_UBIVOL > + bool "ubivol" > + default n > + #depends on HAVE_LIBUBI > + #depends on MTD > + select MTD_UTILS_UBI_UTILS > + select MTD_UTILS > + help > + ubi is the default format for NAND device. > + Say Y if you have NAND or you use UBI on > + your system. > + > + > +config UBIBLACKLIST > + string "List of MTD devices to be excluded for UBI" > + depends on SWUPDATE_UBIVOL > + help > + Define a list of MTD devices that are excluded > + by scan_mtd_device. The devices are still available > + as raw devices. > + The list can be set as a string with the mtd numbers. > + Examples: "0 1 2" > + This excludes mtd0-mtd1-mtd2 to be searched for UBI volumes > + > +config UBIVIDOFFSET > + int "VID Header Offset" > + depends on SWUPDATE_UBIVOL > + default 0 > + help > + Force UBI to set a VID header offset to be 2048 bytes > + instead of the value reported by the kernel. > + In other words, you may ask UBI to avoid using sub-pages. > + This is not recommended since this will require > + more storage overhead, but may be useful > + if your NAND driver incorrectly reports that it can handle > + sub-page accesses when it should not. > + > + > +config CFI > + bool "cfi" > + #depends on MTD > + select MTD_UTILS > + default n > + help > + Handler to store images in flash in raw mode, > + without UBI > + > +config CFIHAMMING1 > + bool "NAND in raw mode with 1bit Hamming OOB (TI)" > + #depends on MTD > + select MTD_UTILS > + default n > + select CFI > + help > + On certain TI's omaps (for example, DM3730 or AM3517), > + the first bootloader (MLO or SPL) must be saved with one bit > + Hamming correction because this is requested by the SOC's ROM. > + However, the Linux driver must use for the rest of the NAND a more > + powerful algorithm to make data reliable, and this causes that > + it is not possible to update SPL by letting the driver to handle > + the OOB area. This handler raws the NAND in raw mode, computing > + the ECC with 1 bit Hamming Code and saving it into OOB > + (assumes sector size of 512 and page size of 2048). > + > + You do not need this if you have not a OMAP SOC. > + > +config RAW > + bool "raw" > + default y > + help > + This is a simple handler that simply copies > + into the destination. > + > +config LUASCRIPTHANDLER > + bool "luascript" > + select LUA > + select LUA_INSTALL_LUA > + select LUA_INSTALL_LUAC > + select LUA_INSTALL_LIBLUA > + default n > + help > + Handler to be called for pre- and post scripts > + written in LUA. > + > +config SHELLSCRIPTHANDLER > + bool "shellscript" > + default n > + help > + Handler to be called for pre- and post scripts > + written as shell scripts. The default shell /bin/sh > + is called. > + > +config HANDLER_IN_LUA > + bool "Handlers in LUA" > + #depends on LUASCRIPTHANDLER > + select LUA > + select LUA_INSTALL_LUA > + select LUA_INSTALL_LUAC > + select LUA_INSTALL_LIBLUA > + > + > + default n > + help > + Allow to write own handlers in LUA. > + They are loaded at the start-up. > + > +config ARCHIVE > + bool "archive" > + #depends on HAVE_LIBARCHIVE > + select LIBARCHIVE > + default n > + help > + Handler using the libarchive to extract tarballs > + into a filesystem. > + > + > +config REMOTE_HANDLER > + bool "Remote handler" > + depends on HAVE_LIBZEROMQ > + default n > + help > + Sometimes the update process should be done > + by another process, where code is already > + provided. The remote handler let communicate > + an external process with SWUpdate, sending > + the image to be updated with the help of the > + zeromq library. > + > +comment "remote handler needs zeromq" > + depends on !HAVE_LIBZEROMQ > + > + > +config SWUPDATE_UBOOT > + bool > + prompt "uboot" > + #depends on HAVE_LIBUBOOTENV > + #depends on HAVE_ZLIB > + select U_BOOT_TOOLS_TOOL_ENV > + select U_BOOT_TOOLS > + select ZLIB > + default n > + help > + Enable it to change U-Boot environment > + during the installation process. > + > +config UBOOT_FWENV > + string > + prompt "U-Boot Environment Configuration file" > + depends on SWUPDATE_UBOOT > + default "/etc/fw_env.config" > + help > + This is the file described in U-Boot documentation > + in the tools directory. It tells where the U-Boot > + environment is saved. > + > +endmenu > + > +endif > diff --git a/rules/swupdate.make b/rules/swupdate.make > new file mode 100644 > index 0000000..2d41f95 > --- /dev/null > +++ b/rules/swupdate.make > @@ -0,0 +1,197 @@ > +# -*-makefile-*- > +# > +# Copyright (C) 2017 by Pedro Lafuente <pedro.lafue...@avt-stoye.de> > +# > +# See CREDITS for details about who has contributed to this project. > +# > +# For further information about the PTXdist project and license conditions > +# see the README file. > +# > + > +# > +# We provide this package > +# > +PACKAGES-$(PTXCONF_SWUPDATE) += swupdate > + > +# > +# Paths and names > +# > +SWUPDATE_VERSION := 2017.01 > +SWUPDATE_MD5 := 90d86de674dc70a19adc92847420700a > +SWUPDATE := swupdate-$(SWUPDATE_VERSION) > +SWUPDATE_SUFFIX := tar.gz > +SWUPDATE_URL := > https://github.com/sbabic/swupdate/archive/$(SWUPDATE_VERSION).$(SWUPDATE_SUFFIX) > > +SWUPDATE_SOURCE := $(SRCDIR)/$(SWUPDATE).$(SWUPDATE_SUFFIX) > +SWUPDATE_DIR := $(BUILDDIR)/$(SWUPDATE) > +SWUPDATE_LICENSE := GNUGPL > + > +# > ---------------------------------------------------------------------------- > > +# Get > +# > ---------------------------------------------------------------------------- > > + > +$(SWUPDATE_SOURCE): > + @$(call targetinfo) > + @$(call get, SWUPDATE) > + @$(call touch) > + > +# > ---------------------------------------------------------------------------- > > +# Extract > +# > ---------------------------------------------------------------------------- > > + > +$(STATEDIR)/swupdate.extract: > + @$(call targetinfo) > +# @$(call clean, $(SWUPDATE_DIR)) > + @$(call extract, SWUPDATE) > + @$(call touch) > +# > ---------------------------------------------------------------------------- > > +# Prepare > +# > ---------------------------------------------------------------------------- > > + > +#SWUPDATE_CONF_ENV := $(CROSS_ENV) > +# > +# autoconf > +# > +#SWUPDATE_CONF_TOOL := autoconf > +SWUPDATE_CONF_OPT := allyesconfig > +SYSROOT_TOOLCHAIN=sysroot-arm-cortexa8-linux-gnueabihf > +CROSS_COMPILE_PATH=$(shell readlink > '${PTXDIST_WORKSPACE}/selected_toolchain')/$(PTXCONF_COMPILER_PREFIX) > +SYS_ROOT_PATH=$(shell readlink > '${PTXDIST_WORKSPACE}/selected_toolchain' | sed -e > 's/\(bin\)*$$//g')$(SYSROOT_TOOLCHAIN) > + > +INC_MTD_UTILS=$(PTXDIST_PLATFORMDIR)/build-target/$(MTD_UTILS)/include > +INC_LIBCURL=$(PTXDIST_PLATFORMDIR)/build-target/$(LIBCURL)/include > +INC_OPENSSL=$(PTXDIST_PLATFORMDIR)/build-target/$(OPENSSL)/include > +INC_ZLIB=$(PTXDIST_PLATFORMDIR)/build-target/$(ZLIB) > +INC_LIBARCHIVE=$(PTXDIST_PLATFORMDIR)/build-target/$(LIBARCHIVE)/libarchive > > +INC_LIBCONFIG=$(PTXDIST_PLATFORMDIR)/build-target/$(LIBCONFIG)/lib > +INC_JSON_C=$(PTXDIST_PLATFORMDIR)/build-target/$(JSON_C)/lib > +INC_LUA=$(PTXDIST_PLATFORMDIR)/build-target/$(LUA)/src > +ALL_PATH_INC=\-\I\ \$(INC_MTD_UTILS)\ \-\I\ \$(INC_LIBCURL)\ \-\I\ > \$(INC_OPENSSL)\ \-\I\ \$(INC_ZLIB)\ \-\I\ \$(INC_LIBARCHIVE)\ \-\I\ > \$(INC_LIBCONFIG)\ \-\I\ \$(INC_JSON_C)\ \-\I\ \$(INC_LUA) > + > +LIB_MTD_UTILS=$(PTXDIST_PLATFORMDIR)/build-target/$(MTD_UTILS)/arm-cortexa8-linux-gnueabihf/lib > > +LIB_MTD_UTILS_UBI=$(PTXDIST_PLATFORMDIR)/build-target/$(MTD_UTILS)/arm-cortexa8-linux-gnueabihf/ubi-utils > > +LIB_LIBCURL=$(PTXDIST_PLATFORMDIR)/build-target/$(LIBCURL)/lib/.libs > +LIB_OPENSSL=$(PTXDIST_PLATFORMDIR)/build-target/$(OPENSSL) > +LIB_ZLIB=$(PTXDIST_PLATFORMDIR)/build-target/$(ZLIB) > +LIB_LIBARCHIVE=$(PTXDIST_PLATFORMDIR)/build-target/$(LIBARCHIVE)/.libs > +LIB_LIBCONFIG=$(PTXDIST_PLATFORMDIR)/build-target/$(LIBCONFIG)/lib/.libs > +LIB_JSON_C=$(PTXDIST_PLATFORMDIR)/build-target/$(JSON_C)/.libs > +LIB_LUA=$(PTXDIST_PLATFORMDIR)/build-target/$(LUA)/src/.libs > +ALL_PATH_LIB=\-\L\ \$(LIB_MTD_UTILS)\ \-\L\ \$(LIB_MTD_UTILS_UBI)\ > \-\L\ \$(LIB_LIBCURL)\ \-\L\ \$(LIB_LIBCURL)\ \-\L\ \$(LIB_OPENSSL)\ > \-\L\ \$(LIB_ZLIB)\ \-\L\ \$(LIB_LIBARCHIVE)\ \-\L\ \$(LIB_LIBCONFIG)\ > \-\L\ \$(LIB_JSON_C)\ \-\L\ \$(LIB_LUA) > + > +$(STATEDIR)/swupdate.prepare: > + @$(call targetinfo) > + @$(call clean, $(SWUPDATE_DIR)/config.cache) > + cd $(SWUPDATE_DIR) && \ > + make allyesconfig > + sed -i 's,^\(CONFIG_SCRIPTS=\).*,\1'$(PTXCONF_SCRIPTS)',' > $(SWUPDATE_DIR)/.config > + sed -i > 's,^\(CONFIG_HW_COMPATIBILITY=\).*,\1'$(PTXCONF_HW_COMPATIBILITY)',' > $(SWUPDATE_DIR)/.config > + sed -i > 's,^\(CONFIG_HW_COMPATIBILITY_FILE=\).*,\1"'$(PTXCONF_HW_COMPATIBILITY_FILE)'",' > $(SWUPDATE_DIR)/.config > + sed -i > 's,^\(CONFIG_SW_VERSIONS_FILE=\).*,\1"'$(PTXCONF_SW_VERSIONS_FILE)'",' > $(SWUPDATE_DIR)/.config > + sed -i 's,^\(CONFIG_MTD=\).*,\1'$(PTXCONF_MTD)',' > $(SWUPDATE_DIR)/.config > + sed -i 's,^\(CONFIG_LUA=\).*,\1'$(PTXCONF_SWUPDATE_LUA)',' > $(SWUPDATE_DIR)/.config > + sed -i > 's,^\(CONFIG_FEATURE_SYSLOG=\).*,\1'$(PTXCONF_FEATURE_SYSLOG)',' > $(SWUPDATE_DIR)/.config > + sed -i 's,^\(CONFIG_STATIC=\).*,\1'$(PTXCONF_STATIC)',' > $(SWUPDATE_DIR)/.config > + sed -i 's,^\(CONFIG_DEBUG=\).*,\1'$(PTXCONF_SW_UPDATE_DEBUG)',' > $(SWUPDATE_DIR)/.config > + sed -i > 's,^\(CONFIG_DEBUG_PESSIMIZE=\).*,\1'$(PTXCONF_DEBUG_PESSIMIZE)',' > $(SWUPDATE_DIR)/.config > + sed -i 's,^\(CONFIG_WERROR=\).*,\1'$(PTXCONF_WERROR)',' > $(SWUPDATE_DIR)/.config > + sed -i 's,^\(CONFIG_NOCLEANUP=\).*,\1'$(PTXCONF_NOCLEANUP)',' > $(SWUPDATE_DIR)/.config > + sed -i 's,^\(CONFIG_DOWNLOAD=\).*,\1'$(PTXCONF_DOWNLOAD)',' > $(SWUPDATE_DIR)/.config > + sed -i 's,^\(CONFIG_HASH_VERIFY=\).*,\1'$(PTXCONF_HASH_VERIFY)',' > $(SWUPDATE_DIR)/.config > + sed -i 's,^\(CONFIG_SIGNED_IMAGES=\).*,\1'$(PTXCONF_SCRIPTS)',' > $(SWUPDATE_DIR)/.config > + sed -i > 's,^\(CONFIG_ENCRYPTED_IMAGES=\).*,\1'$(PTXCONF_ENCRYPTED_IMAGES)',' > $(SWUPDATE_DIR)/.config > + sed -i 's,^\(CONFIG_SURICATTA=\).*,\1'$(PTXCONF_SURICATTA)',' > $(SWUPDATE_DIR)/.config > + sed -i > 's,^\(CONFIG_SURICATTA_SSL=\).*,\1'$(PTXCONF_SURICATTA_SSL)',' > $(SWUPDATE_DIR)/.config > + sed -i > 's,^\(CONFIG_SURICATTA_STATE_CHOICE_NONE=\).*,\1'$(PTXCONF_SURICATTA_STATE_CHOICE_NONE)',' > $(SWUPDATE_DIR)/.config > + sed -i > 's,^\(CONFIG_SURICATTA_STATE_CHOICE_UBOOT=\).*,\1'$(PTXCONF_SURICATTA_STATE_CHOICE_UBOOT)',' > $(SWUPDATE_DIR)/.config > + sed -i > 's,^\(CONFIG_SURICATTA_STATE_UBOOT=\).*,\1'$(PTXCONF_SCRIPTS)',' > $(SWUPDATE_DIR)/.config > + sed -i > 's,^\(CONFIG_SURICATTA_HAWKBIT=\).*,\1'$(PTXCONF_SURICATTA_HAWKBIT)',' > $(SWUPDATE_DIR)/.config > + sed -i > 's,^\(CONFIG_SURICATTA_SERVER_NONE=\).*,\1'$(PTXCONF_SURICATTA_SERVER_NONE)',' > $(SWUPDATE_DIR)/.config > + sed -i 's,^\(CONFIG_WEBSERVER=\).*,\1'$(PTXCONF_WEBSERVER)',' > $(SWUPDATE_DIR)/.config > + sed -i 's,^\(CONFIG_MONGOOSE=\).*,\1'$(PTXCONF_MONGOOSE)',' > $(SWUPDATE_DIR)/.config > + sed -i 's,^\(CONFIG_MONGOOSELUA=\).*,\1'$(PTXCONF_MONGOOSELUA)',' > $(SWUPDATE_DIR)/.config > + sed -i 's,^\(CONFIG_MONGOOSEIPV6=\).*,\1'$(PTXCONF_MONGOOSEIPV6)',' > $(SWUPDATE_DIR)/.config > + sed -i 's,^\(CONFIG_MONGOOSESSL=\).*,\1'$(PTXCONF_MONGOOSESSL)',' > $(SWUPDATE_DIR)/.config > + sed -i 's,^\(CONFIG_GUNZIP=\).*,\1'$(PTXCONF_GUNZIP)',' > $(SWUPDATE_DIR)/.config > + sed -i 's,^\(CONFIG_LIBCONFIG=\).*,\1'$(PTXCONF_LIBCONFIG)',' > $(SWUPDATE_DIR)/.config > + sed -i > 's,^\(CONFIG_LIBCONFIGROOT=\).*,\1"'$(PTXCONF_LIBCONFIGROOT)'",' > $(SWUPDATE_DIR)/.config > + sed -i 's,^\(CONFIG_JSON=\).*,\1'$(PTXCONF_JSON)',' > $(SWUPDATE_DIR)/.config > + sed -i 's,^\(CONFIG_LUAEXTERNAL=\).*,\1'$(PTXCONF_LUAEXTERNAL)',' > $(SWUPDATE_DIR)/.config > + sed -i > 's,^\(CONFIG_SETEXTPARSERNAME=\).*,\1'$(PTXCONF_SETEXTPARSERNAME)',' > $(SWUPDATE_DIR)/.config > + sed -i > 's,^\(CONFIG_EXTPARSERNAME=\).*,\1'$(PTXCONF_EXTPARSERNAME)',' > $(SWUPDATE_DIR)/.config > + sed -i > 's,^\(CONFIG_SETSWDESCRIPTION=\).*,\1'$(PTXCONF_SETSWDESCRIPTION)',' > $(SWUPDATE_DIR)/.config > + sed -i > 's,^\(CONFIG_SWDESCRIPTION=\).*,\1'$(PTXCONF_SWDESCRIPTION)',' > $(SWUPDATE_DIR)/.config > + sed -i 's,^\(CONFIG_UBIVOL=\).*,\1'$(PTXCONF_UBIVOL)',' > $(SWUPDATE_DIR)/.config > + sed -i 's,^\(CONFIG_UBIBLACKLIST=\).*,\1'$(PTXCONF_UBIBLACKLIST)',' > $(SWUPDATE_DIR)/.config > + sed -i 's,^\(CONFIG_UBIVIDOFFSET=\).*,\1'$(PTXCONF_UBIVIDOFFSET)',' > $(SWUPDATE_DIR)/.config > + sed -i 's,^\(CONFIG_CFI=\).*,\1'$(PTXCONF_CFI)',' > $(SWUPDATE_DIR)/.config > + sed -i 's,^\(CONFIG_CFIHAMMING1=\).*,\1'$(PTXCONF_CFIHAMMING1)',' > $(SWUPDATE_DIR)/.config > + sed -i 's,^\(CONFIG_RAW=\).*,\1'$(PTXCONF_RAW)',' > $(SWUPDATE_DIR)/.config > + sed -i > 's,^\(CONFIG_LUASCRIPTHANDLER=\).*,\1'$(PTXCONF_LUASCRIPTHANDLER)',' > $(SWUPDATE_DIR)/.config > + sed -i > 's,^\(CONFIG_SHELLSCRIPTHANDLER=\).*,\1'$(PTXCONF_SHELLSCRIPTHANDLER)',' > $(SWUPDATE_DIR)/.config > + sed -i > 's,^\(CONFIG_HANDLER_IN_LUA=\).*,\1'$(PTXCONF_HANDLER_IN_LUA)',' > $(SWUPDATE_DIR)/.config > + sed -i 's,^\(CONFIG_ARCHIVE=\).*,\1'$(PTXCONF_ARCHIVE)',' > $(SWUPDATE_DIR)/.config > + sed -i > 's,^\(CONFIG_REMOTE_HANDLER=\).*,\1'$(PTXCONF_REMOTE_HANDLER)',' > $(SWUPDATE_DIR)/.config > + sed -i 's,^\(CONFIG_UBOOT=\).*,\1'$(PTXCONF_SWUPDATE_UBOOT)',' > $(SWUPDATE_DIR)/.config > + sed -i 's,^\(CONFIG_UBOOT_FWENV=\).*,\1"'$(PTXCONF_UBOOT_FWENV)'",' > $(SWUPDATE_DIR)/.config > + > +#sed -i > 's,^\(CONFIG_CROSS_COMPILE=\).*,\1"'$(PTXCONF_CROSS_COMPILE)'",' > $(SWUPDATE_DIR)/.config > + sed -i > 's,^\(CONFIG_CROSS_COMPILE=\).*,\1"'$(CROSS_COMPILE_PATH)'",' > $(SWUPDATE_DIR)/.config > +#sed -i 's,^\(CONFIG_SYSROOT=\).*,\1"'$(PTXCONF_SYSROOT)'",' > $(SWUPDATE_DIR)/.config > + sed -i 's,^\(CONFIG_SYSROOT=\).*,\1"'$(SYS_ROOT_PATH)'",' > $(SWUPDATE_DIR)/.config > + > +#sed -i 's,^\(CONFIG_EXTRA_CFLAGS=\).*,\1"'$(PTXCONF_EXTRA_CFLAGS)'",' > $(SWUPDATE_DIR)/.config > + sed -i 's,^\(CONFIG_EXTRA_CFLAGS=\).*,\1"'$(ALL_PATH_INC)'",' > $(SWUPDATE_DIR)/.config > +#sed -i > 's,^\(CONFIG_EXTRA_LDFLAGS=\).*,\1"'$(PTXCONF_EXTRA_LDFLAGS)'",' > $(SWUPDATE_DIR)/.config > + sed -i 's,^\(CONFIG_EXTRA_LDFLAGS=\).*,\1"'$(ALL_PATH_LIB)'",' > $(SWUPDATE_DIR)/.config > + sed -i > 's,^\(CONFIG_EXTRA_LDLIBS=\).*,\1"'$(PTXCONF_EXTRA_LDLIBS)'",' > $(SWUPDATE_DIR)/.config > + sed -e '/=$$/s/^#*/# /' -e '/^#/s/=$$/ is not set /' -i > $(SWUPDATE_DIR)/.config > + @$(call touch) > + > +# > ---------------------------------------------------------------------------- > > +# Compile > +# > ---------------------------------------------------------------------------- > > +$(STATEDIR)/swupdate.compile: > + @$(call targetinfo) > + @$(call world/compile, SWUPDATE) > + @$(call touch) > + > +# > ---------------------------------------------------------------------------- > > +# Install > +# > ---------------------------------------------------------------------------- > > + > +$(STATEDIR)/swupdate.install: > + @$(call targetinfo) > +# @$(call world/install, SWUPDATE) > + @$(call touch) > + > +# > ---------------------------------------------------------------------------- > > +# Target-Install > +# > ---------------------------------------------------------------------------- > > + > +$(STATEDIR)/swupdate.targetinstall: > + @$(call targetinfo) > + > + @$(call install_init, swupdate) > + @$(call install_fixup, swupdate,PRIORITY,optional) > + @$(call install_fixup, swupdate,SECTION,base) > + @$(call install_fixup, swupdate,AUTHOR,"Pedro Lafuente > <pedro.lafue...@avt-stoye.de>") > + @$(call install_fixup, swupdate,DESCRIPTION,missing) > + > + @$(call install_copy, swupdate, 0, 0, 0755, > $(SWUPDATE_DIR)/swupdate_unstripped, /usr/bin/swupdate_unstripped) > + @$(call install_copy, swupdate, 0, 0, 0755, > $(SWUPDATE_DIR)/swupdate, /usr/bin/swupdate) > + @$(call install_copy, swupdate, 0, 0, 0755, > $(SWUPDATE_DIR)/progress_unstripped, /usr/bin/progress_unstripped) > + @$(call install_copy, swupdate, 0, 0, 0755, > $(SWUPDATE_DIR)/progress, /usr/bin/progress) > + @$(call install_tree, swupdate, 0, 0, $(SWUPDATE_DIR)/www/, /www/) > + > + @$(call install_finish, swupdate) > + @$(call touch) > + > +# > ---------------------------------------------------------------------------- > > +# Clean > +# > ---------------------------------------------------------------------------- > > + > +$(STATEDIR)/swupdate.clean: > + @$(call targetinfo) > + @$(call clean_pkg, SWUPDATE) > + > +# vim: syntax=make > > > _______________________________________________ > ptxdist mailing list > ptxdist@pengutronix.de _______________________________________________ ptxdist mailing list ptxdist@pengutronix.de
