'Twas brillig, and Rémi Denis-Courmont at 18/05/11 07:37 did gyre and
gimble:
> On Tue, 17 May 2011 21:51:35 +0200, Michael Trunner <mich...@trunner.de>
> wrote:
>> I'm trying to setup Pulseaudio to receive RTP/Multicast steams. Sender
>> should be vlc, (and receiver should be pulseaudio). I activated
>> module-rtp-recv (and module-rtp-send) with papref, but I can't get it
>> work. Can some one explain me what I have to do? Or how to debug it.
>
> First you need to make sure that VLC uses an RTP payload format that
> PulseAudio understands, typically L16/44100/2 (signed big endian 16-bits
> stereo at 44100 Hz). By default, VLC will not decode the audio. Also make
> sure SAP is enabled.
>
> For example:
> # IP=224.0.0.42
> # vlc --sout-keep --no-sout-video --no-sout-spu \
> --sout
> "#transcode{acodec=s16b,samplerate=44100}:gather:rtp{sap,dst=$IP}"
>
> Then you need to configure PulseAudio to use the standard SAP address as
> specified in IETF RFC2974 §3, corresponding to the multicast scope that VLC
> is configured to use, in particular:
> - 224.2.127.254 (SAP.MCAST.NET) for global IPv4,
> - ff0e::2:7ffe for global IPv6,
> - 224.0.0.255 for link-local IPv4,
> - ff02::2:7ffe for link-local IPv6.
Many thanks for the info Rémi :)
> By default, PulseAudio uses a proprietary non-standard SAP group, namely
> 224.0.0.56. This cannot interoperate with VLC.
Interesting. I see from the history:
commit e1887b552ceb324f70732c85c7458119e03718b7
Author: Lennart Poettering <lenn...@poettering.net>
Date: Sun Apr 16 11:13:20 2006 +0000
change default mcast address once again, to make sure our traffic
doesn't leave the network by default
Previously the address was 224.0.1.3
The change before that is:
commit c999fe40b841b035c7d0c873b4a4875e12e9c9a4
Author: Lennart Poettering <lenn...@poettering.net>
Date: Sun Apr 16 09:15:51 2006 +0000
* deal properly with underruns, overflows and packet losses
* change default mcast address
* detect RTP loops
Which had the address as 224.0.1.2. This was the address used when the
module was committed.
This default can be overridden in the module-rtp-recv module with the
sap_address= argument. And with the module-rtp-send module with the
destination= argument.
Hope that helps.
If you have any recommendations for the defaults, please feel free to
suggest them, but I guess the intention was to keep the traffic in house
by default. We should likely expose via paprefs the ability to choose a
public mutlicast group or something. WDYT?
Col
--
Colin Guthrie
gmane(at)colin.guthr.ie
http://colin.guthr.ie/
Day Job:
Tribalogic Limited [http://www.tribalogic.net/]
Open Source:
Mageia Contributor [http://www.mageia.org/]
PulseAudio Hacker [http://www.pulseaudio.org/]
Trac Hacker [http://trac.edgewall.org/]
_______________________________________________
pulseaudio-discuss mailing list
pulseaudio-discuss@mail.0pointer.de
https://tango.0pointer.de/mailman/listinfo/pulseaudio-discuss
