Hi,
I ahve been trying to install plan9 on a standalone pc from the live CD,
downloaded about 2-3 days ago from the plan9 site.
The live CD has run ok on my system .
Upon attempting to install after setting up
DMA = on (have tried =off too)
mouse=ps2intellimouse (tried ps2 too)
vga= as suggested
etc when the interface starts I get a message like this
**output begins here
cpu0: registers for bind 120
Flags=10297 Trap=E E Code=2 PC F0100A3D SS=F3F0 USP=20A55
AX 00000011 BX 00000006 CX 00000000 DX 00000009
S1 00000001 D1 000020ASE BP 00000009
CS 0010 DS 0008 ES 0008 FS 001b GS 0017
MCA 40de 1064a MCT fc0000000000d1dd
ur f0e42f34 up f0233318
panic: fault: 0x9
cpu0 exiting
dump stack disabled
cpu0 exiting
**end of output
The numbers after GS may not be correct, i copied it down on paper having no
way to save it, couldn't read the result there to well.
I tried a few times and got varying messages at the beginning of the output
"cpu0: registers for sleep"
"cpu0 registers for window 114"
differing values for the mid-section.
and at the end invariably:
panic: fault: 0x9
It does not seem that the error is repeatable.
The system is a dual boot system (Windows98/NetBSD) the boot is handled by GAG
Bootloader.
Here is the output of dmesg from NetBSD will give an idea of the hardware
NetBSD 3.0.1 (GENERIC) #0: Thu Jul 13 23:43:47 UTC 2006
[EMAIL
PROTECTED]:/home/builds/ab/netbsd-3-0-1-RELEASE/i386/200607131826Z-obj/home/builds/ab/netbsd-3-0-1-RELEASE/src/sys/arch/i386/compile/GENERIC
total memory = 383 MB
avail memory = 367 MB
BIOS32 rev. 0 found at 0xfdb10
mainbus0 (root)
cpu0 at mainbus0: (uniprocessor)
cpu0: AMD Athlon XP 1600+ (686-class), 1400.19 MHz, id 0x662
cpu0: features
c3cbfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR>
cpu0: features c3cbfbff<PGE,MCA,CMOV,PAT,PSE36,MPC,MMXX,MMX>
cpu0: features c3cbfbff<FXSR,SSE,3DNOW2,3DNOW>
cpu0: "AMD Athlon(tm) XP 1600+ "
cpu0: I-cache 64 KB 64B/line 2-way, D-cache 64 KB 64B/line 2-way
cpu0: L2 cache 256 KB 64B/line 16-way
cpu0: ITLB 16 4 KB entries fully associative, 8 4 MB entries fully
associative
cpu0: DTLB 32 4 KB entries fully associative, 8 4 MB entries 4-way
cpu0: 8 page colors
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
pchb0 at pci0 dev 0 function 0
pchb0: VIA Technologies VT8363 (Apollo KT133) Host Bridge (rev. 0x03)
agp0 at pchb0: aperture at 0xe0000000, size 0x10000000
ppb0 at pci0 dev 1 function 0: VIA Technologies VT8363 (Apollo KT133)
PCI to AGP Bridge (rev. 0x00)
pci1 at ppb0 bus 1
pci1: i/o space, memory space enabled
vga1 at pci1 dev 0 function 0: Nvidia GeForce2 MX 100/200 (rev. 0xb2)
wsdisplay0 at vga1 kbdmux 1: console (80x25, vt100 emulation)
wsmux1: connecting to wsdisplay0
pcib0 at pci0 dev 7 function 0
pcib0: VIA Technologies VT82C686A PCI-ISA Bridge (rev. 0x40)
viaide0 at pci0 dev 7 function 1
viaide0: VIA Technologies VT82C686A (Apollo KX133) ATA100 controller
viaide0: bus-master DMA support present
viaide0: primary channel configured to compatibility mode
viaide0: primary channel interrupting at irq 14
atabus0 at viaide0 channel 0
viaide0: secondary channel configured to compatibility mode
viaide0: secondary channel interrupting at irq 15
atabus1 at viaide0 channel 1
uhci0 at pci0 dev 7 function 2: VIA Technologies VT83C572 USB
Controller (rev. 0x1a)
uhci0: interrupting at irq 9
usb0 at uhci0: USB revision 1.0
uhub0 at usb0
uhub0: VIA Technologies UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1 at pci0 dev 7 function 3: VIA Technologies VT83C572 USB
Controller (rev. 0x1a)
uhci1: interrupting at irq 9
usb1 at uhci1: USB revision 1.0
uhub1 at usb1
uhub1: VIA Technologies UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
VIA Technologies VT82C686A SMBus Controller (SMBus serial bus, revision
0x40) at pci0 dev 7 function 4 not configured
auvia0 at pci0 dev 7 function 5: VIA Technologies VT82C686A AC'97 Audio
(rev 0x50)
auvia0: interrupting at irq 10
auvia0: ac97: Avance Logic ALC200/ALC201 codec; headphone, 18 bit DAC,
18 bit ADC, Realtek 3D
auvia0: ac97: ext id 605<AC97_22,AMAP,SPDIF,VRA>
audio0 at auvia0: full duplex, mmap, independent
emuxki0 at pci0 dev 10 function 0: Creative Labs SBLive! EMU 10000
(audio mul, revision 0x07)
emuxki0: ac97: SigmaTel STAC9708 codec; 18 bit DAC, 18 bit ADC,
SigmaTel 3D
emuxki0: ac97: ext id 80<SDAC>
audio1 at emuxki0: full duplex, mmap, independent
emuxki0: interrupting at irq 10
joy0 at pci0 dev 10 function 1: Creative Labs PCI Gameport Joystick
(rev 0x07)
joy0: joystick not connected
Lucent Technologies LTMODEM (miscellaneous communications) at pci0 dev
12 function 0 not configured
rtk0 at pci0 dev 15 function 0: Realtek 8139 10/100BaseTX
rtk0: interrupting at irq 9
rtk0: Ethernet address 00:0a:cd:10:d4:f1
ukphy0 at rtk0 phy 7: Generic IEEE 802.3u media interface
ukphy0: OUI 0x000000, model 0x0000, rev. 0
ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
isa0 at pcib0
lpt0 at isa0 port 0x378-0x37b irq 7
com0 at isa0 port 0x3f8-0x3ff irq 4: ns16550a, working fifo
com1 at isa0 port 0x2f8-0x2ff irq 3: ns16550a, working fifo
pckbc0 at isa0 port 0x60-0x64
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pms0 at pckbc0 (aux slot)
pckbc0: using irq 12 for aux slot
wsmouse0 at pms0 mux 0
pcppi0 at isa0 port 0x61
midi0 at pcppi0: PC speaker
sysbeep0 at pcppi0
isapnp0 at isa0 port 0x279: ISA Plug 'n Play device support
npx0 at isa0 port 0xf0-0xff: using exception 16
fdc0 at isa0 port 0x3f0-0x3f7 irq 6 drq 2
isapnp0: no ISA Plug 'n Play devices found
fd0 at fdc0 drive 0: 1.44MB, 80 cyl, 2 head, 18 sec
Kernelized RAIDframe activated
wd0 at atabus0 drive 0: <WDC WD800BB-00JKC0>
wd0: drive supports 16-sector PIO transfers, LBA addressing
wd0: 76319 MB, 155061 cyl, 16 head, 63 sec, 512 bytes/sect x 156301488
sectors
wd0: 32-bit data port
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100)
wd1 at atabus0 drive 1: <MAXTOR 6L040J2>
wd1: drive supports 16-sector PIO transfers, LBA addressing
wd1: 38172 MB, 77557 cyl, 16 head, 63 sec, 512 bytes/sect x 78177792
sectors
wd1: 32-bit data port
wd1: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133)
wd0(viaide0:0:0): using PIO mode 4, Ultra-DMA mode 5 (Ultra/100) (using
DMA)
wd1(viaide0:0:1): using PIO mode 4, Ultra-DMA mode 5 (Ultra/100) (using
DMA)
atapibus0 at atabus1: 2 targets
cd0 at atapibus0 drive 0: <SONY CD-RW CRX175E, , 1.0j> cdrom
removable
cd0: 32-bit data port
cd0: drive supports PIO mode 4, DMA mode 2
cd0(viaide0:1:0): using PIO mode 4, DMA mode 2 (using DMA)
boot device: wd0
root on wd0a dumps on wd0b
root file system type: ffs
wsdisplay0: screen 1 added (80x25, vt100 emulation)
wsdisplay0: screen 2 added (80x25, vt100 emulation)
wsdisplay0: screen 3 added (80x25, vt100 emulation)
wsdisplay0: screen 4 added (80x25, vt100 emulation)
## end of dmesg
checking on plan9 website my hardware would seem to be ok, unless I have missed
something!!
Any help most grategully received.
Regards,
Alasdair
