http://bugzilla.kernel.org/show_bug.cgi?id=5904
Summary: wrong state of laptop lid on startup
Kernel Version: 2.6.15
Status: NEW
Severity: normal
Owner: [EMAIL PROTECTED]
Submitter: [EMAIL PROTECTED]
CC: [EMAIL PROTECTED]
Distribution: Gentoo Linux
Hardware Environment: Acer Travelmate 243LC
Problem Description:
Hi
When my laptop is started and my laptop lid is open,
/proc/acpi/button/lid/LID/state says "closed". When I close it once and
open it again once the value is set correctly. This is very annoying
cause my screensaver always invokes on startup.
Linux version 2.6.15-suspend2 ([EMAIL PROTECTED]) (gcc version 3.4.4 (Gentoo
3.4.4-r1, ssp-3.4.4-1.0, pie-8.7.8)) #2 PREEMPT Sat Jan 14 23:12:45 C
ET 2006
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000ce000 - 00000000000d0000 (reserved)
BIOS-e820: 00000000000d8000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000000eee0000 (usable)
BIOS-e820: 000000000eee0000 - 000000000eeeb000 (ACPI data)
BIOS-e820: 000000000eeeb000 - 000000000ef00000 (ACPI NVS)
BIOS-e820: 000000000ef00000 - 0000000010000000 (reserved)
BIOS-e820: 00000000fec10000 - 00000000fec20000 (reserved)
BIOS-e820: 00000000ff800000 - 00000000ffc00000 (reserved)
BIOS-e820: 00000000fffffc00 - 0000000100000000 (reserved)
238MB LOWMEM available.
found SMP MP-table at 000f63f0
On node 0 totalpages: 61152
DMA zone: 4096 pages, LIFO batch:0
DMA32 zone: 0 pages, LIFO batch:0
Normal zone: 57056 pages, LIFO batch:15
HighMem zone: 0 pages, LIFO batch:0
DMI present.
ACPI: RSDP (v000 PTLTD ) @ 0x000f6420
ACPI: RSDT (v001 PTLTD Montara 0x06040000 LTP 0x00000000) @ 0x0eee5e05
ACPI: FADT (v001 Acer Yuhina 0x06040000 PTL 0x00000001) @ 0x0eeeaed2
ACPI: BOOT (v001 PTLTD $SBFTBL$ 0x06040000 LTP 0x00000001) @ 0x0eeeafd8
ACPI: DSDT (v001 ANNI Yuhina 0x06040000 MSFT 0x0100000e) @ 0x00000000
Intel MultiProcessor Specification v1.4
Virtual Wire compatibility mode.
SMP mptable: bad signature [0x0]!
BIOS bug, MP table errors detected!...
... disabling SMP support. (tell your hw vendor)
Allocating PCI resources starting at 20000000 (gap: 10000000:eec10000)
Built 1 zonelists
Kernel command line: root=/dev/hda3 resume2=/dev/hda2 init=/sbin/initng lapic
Local APIC disabled by BIOS -- reenabling.
Found and enabled local APIC!
mapped APIC to ffffd000 (fee00000)
Initializing CPU#0
PID hash table entries: 1024 (order: 10, 16384 bytes)
Detected 2498.310 MHz processor.
Using tsc for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 238724k/244608k available (2212k kernel code, 5452k reserved, 740k data,
148k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 5002.83 BogoMIPS (lpj=10005677)
Mount-cache hash table entries: 512
CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000 00004400
00000000 00000000
CPU: After vendor identify, caps: bfebfbff 00000000 00000000 00000000 00004400
00000000 00000000
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 128K
CPU: After all inits, caps: bfebfbff 00000000 00000000 00000080 00004400
00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU0: Intel P4/Xeon Extended MCE MSRs (12) available
CPU0: Thermal monitoring enabled
mtrr: v2.0 (20020519)
CPU: Intel(R) Celeron(R) CPU 2.50GHz stepping 09
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
ACPI-0284: *** Info: Table [DSDT] replaced by host OS
ACPI: setting ELCR to 0200 (from 0c30)
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfd6b4, last bus=2
PCI: Using configuration type 1
ACPI: Subsystem revision 20050902
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
Boot video device is 0000:00:02.0
PCI quirk: region 1000-107f claimed by ICH4 ACPI/GPIO/TCO
PCI quirk: region 1180-11bf claimed by ICH4 GPIO
PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIB._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 10 11) *5
ACPI: PCI Interrupt Link [LNKB] (IRQs *10 11)
ACPI: PCI Interrupt Link [LNKC] (IRQs *10 11)
ACPI: PCI Interrupt Link [LNKD] (IRQs *11)
ACPI: PCI Interrupt Link [LNKE] (IRQs 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs *10 11)
ACPI: PCI Interrupt Link [LNKG] (IRQs *10 11)
ACPI: PCI Interrupt Link [LNKH] (IRQs 10 11) *4
ACPI: Embedded Controller [EC] (gpe 28)
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
PCI: Ignore bogus resource 6 [0:0] of 0000:00:02.0
PCI: Bus 3, cardbus bridge: 0000:02:04.0
IO window: 00003400-000034ff
IO window: 00003800-000038ff
PREFETCH window: 20000000-21ffffff
MEM window: 26000000-27ffffff
PCI: Bus 7, cardbus bridge: 0000:02:04.1
IO window: 00003c00-00003cff
IO window: 00001400-000014ff
PREFETCH window: 22000000-23ffffff
MEM window: 28000000-29ffffff
PCI: Bridge: 0000:00:1e.0
IO window: 3000-3fff
MEM window: e0200000-e02fffff
PREFETCH window: 20000000-24ffffff
PCI: Setting latency timer of device 0000:00:1e.0 to 64
ACPI: PCI Interrupt Link [LNKF] enabled at IRQ 10
PCI: setting IRQ 10 as level-triggered
ACPI: PCI Interrupt 0000:02:04.0[A] -> Link [LNKF] -> GSI 10 (level, low) ->
IRQ 10
ACPI: PCI Interrupt Link [LNKG] enabled at IRQ 10
ACPI: PCI Interrupt 0000:02:04.1[B] -> Link [LNKG] -> GSI 10 (level, low) ->
IRQ 10
Simple Boot Flag at 0x3c set to 0x1
Machine check exception polling timer started.
SGI XFS with no debug enabled
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered
vesafb: Intel Corporation, Intel(r)852MG/852MGE/855MG/855MGE Graphics
Controller, Hardware Version 0.0 (OEM: Intel(r)852MG/852MGE/855MG/855MGE
Graphics Chip Accelerated VGA BIOS)
vesafb: VBE version: 3.0
vesafb: VBIOS/hardware doesn't support DDC transfers
vesafb: no monitor limits have been set
vesafb: scrolling: redraw
Console: switching to colour frame buffer device 128x48
vesafb: framebuffer at 0xe8000000, mapped to 0xcf880000, using 6144k, total
16192k
fb0: VESA VGA frame buffer device
ACPI: AC Adapter [AC] (on-line)
ACPI: Battery Slot [BAT0] (battery present)
ACPI: Power Button (FF) [PWRF]
ACPI: Lid Switch [LID]
ACPI: Sleep Button (CM) [SLP2]
ACPI: Video Device [VGA] (multi-head: yes rom: no post: no)
Using specific hotkey driver
ACPI: CPU0 (power states: C1[C1] C2[C2])
ACPI: Thermal Zone [THRS] (58 C)
ACPI: Thermal Zone [THRC] (52 C)
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected an Intel 855 Chipset.
agpgart: Detected 16252K stolen memory.
agpgart: AGP aperture is 128M @ 0xe8000000
[drm] Initialized drm 1.0.0 20040925
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
PCI: setting IRQ 11 as level-triggered
ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [LNKA] -> GSI 11 (level, low) ->
IRQ 11
[drm] Initialized i915 1.1.0 20040405 on minor 0:
[drm] Initialized i915 1.1.0 20040405 on minor 1:
intelfb: Framebuffer driver for Intel(R) 830M/845G/852GM/855GM/865G/915G/915GM
chipsets
intelfb: Version 0.9.2
ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [LNKA] -> GSI 11 (level, low) ->
IRQ 11
intelfb: Cannot reserve FB region.
i8042.c: Detected active multiplexing controller, rev 1.1.
serio: i8042 AUX0 port at 0x60,0x64 irq 12
serio: i8042 AUX1 port at 0x60,0x64 irq 12
serio: i8042 AUX2 port at 0x60,0x64 irq 12
serio: i8042 AUX3 port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
8139too Fast Ethernet driver 0.9.27
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11
ACPI: PCI Interrupt 0000:02:0a.0[A] -> Link [LNKD] -> GSI 11 (level, low) ->
IRQ 11
eth0: RealTek RTL8139 at 0xcf80a000, 00:0a:e4:4a:d9:20, IRQ 11
eth0: Identified 8139 chip type 'RTL-8101'
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <[EMAIL PROTECTED]>
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH4: IDE controller at PCI slot 0000:00:1f.1
PCI: Enabling device 0000:00:1f.1 (0005 -> 0007)
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 10
ACPI: PCI Interrupt 0000:00:1f.1[A] -> Link [LNKC] -> GSI 10 (level, low) ->
IRQ 10
ICH4: chipset revision 3
ICH4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x1810-0x1817, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0x1818-0x181f, BIOS settings: hdc:DMA, hdd:pio
Probing IDE interface ide0...
input: AT Translated Set 2 keyboard as /class/input/input0
hda: HITACHI_DK23FA-30, ATA DISK drive
Synaptics Touchpad, model: 1, fw: 5.8, id: 0x9248b1, caps: 0x904713/0x4000
input: SynPS/2 Synaptics TouchPad as /class/input/input1
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: QSI CD-RW/DVD-ROM SBW-242, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 128KiB
hda: 58605120 sectors (30005 MB) w/2048KiB Cache, CHS=58140/16/63, UDMA(100)
hda: cache flushes supported
hda: hda1 hda2 hda3
hdc: ATAPI 24X DVD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
ACPI: PCI Interrupt 0000:02:04.0[A] -> Link [LNKF] -> GSI 10 (level, low) ->
IRQ 10
Yenta: CardBus bridge found at 0000:02:04.0 [1025:0039]
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:02:04.0, mfunc 0x00921b22, devctl 0x64
Yenta: ISA IRQ mask 0x00b8, PCI irq 10
Socket status: 30000020
pcmcia: parent PCI bridge I/O window: 0x3000 - 0x3fff
pcmcia: parent PCI bridge Memory window: 0xe0200000 - 0xe02fffff
pcmcia: parent PCI bridge Memory window: 0x20000000 - 0x24ffffff
ACPI: PCI Interrupt 0000:02:04.1[B] -> Link [LNKG] -> GSI 10 (level, low) ->
IRQ 10
Yenta: CardBus bridge found at 0000:02:04.1 [1025:0039]
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:02:04.1, mfunc 0x00921b22, devctl 0x64
Yenta: ISA IRQ mask 0x00b8, PCI irq 10
Socket status: 30000006
pcmcia: parent PCI bridge I/O window: 0x3000 - 0x3fff
pcmcia: parent PCI bridge Memory window: 0xe0200000 - 0xe02fffff
pcmcia: parent PCI bridge Memory window: 0x20000000 - 0x24ffffff
usbmon: debugfs is not available
ACPI: PCI Interrupt Link [LNKH] enabled at IRQ 11
ACPI: PCI Interrupt 0000:00:1d.7[D] -> Link [LNKH] -> GSI 11 (level, low) ->
IRQ 11
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: debug port 1
PCI: cache line size of 128 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:1d.7: irq 11, io mem 0xe0100000
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 6 ports detected
USB Universal Host Controller Interface driver v2.3
ACPI: PCI Interrupt 0000:00:1d.0[A] -> Link [LNKA] -> GSI 11 (level, low) ->
IRQ 11
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.0: irq 11, io base 0x00001820
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.1[B] -> Link [LNKD] -> GSI 11 (level, low) ->
IRQ 11
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.1: irq 11, io base 0x00001840
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.2[C] -> Link [LNKC] -> GSI 10 (level, low) ->
IRQ 10
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.2: irq 10, io base 0x00001860
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
pccard: CardBus card inserted into slot 0
usb 2-2: new low speed USB device using uhci_hcd and address 2
input: Darfon USB Mouse as /class/input/input2
input: USB HID v1.10 Mouse [Darfon USB Mouse] on usb-0000:00:1d.0-2
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
Advanced Linux Sound Architecture Driver Version 1.0.10rc3 (Mon Nov 07 13:30:21
2005 UTC).
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 10
ACPI: PCI Interrupt 0000:00:1f.5[B] -> Link [LNKB] -> GSI 10 (level, low) ->
IRQ 10
PCI: Setting latency timer of device 0000:00:1f.5 to 64
intel8x0_measure_ac97_clock: measured 55333 usecs
intel8x0: clocking to 48000
ALSA device list:
#0: Intel 82801DB-ICH4 with CS4299 at 0xe0100c00, irq 10
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 3, 32768 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 10
IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
p4-clockmod: P4/Xeon(TM) CPU On-Demand Clock Modulation available
Using IPI Shortcut mode
Suspend2 Core.
Suspend2 Compression Driver loading.
Suspend2 Encryption Driver loading.
Suspend2 Swap Writer loading.
ACPI wakeup devices:
LID LANC MODM
ACPI: (supports S0 S3 S4 S5)
Suspend2 2.2-rc16: Swapwriter: Signature found.
Suspend2 2.2-rc16: Suspending enabled.
swapper(1): READ block 0 size 4096 on hda2
XFS mounting filesystem hda3
Ending clean XFS mount for filesystem: hda3
VFS: Mounted root (xfs filesystem) readonly.
Freeing unused kernel memory: 148k freed
IA-32 Microcode Update Driver: v1.14 <[EMAIL PROTECTED]>
microcode: CPU0 updated from revision 0x17 to 0x2e, date = 08112004
Adding 500464k swap on /dev/hda2. Priority:-1 extents:1 across:500464k
------- You are receiving this mail because: -------
You are the assignee for the bug, or are watching the assignee.
-------------------------------------------------------
This SF.net email is sponsored by: Splunk Inc. Do you grep through log files
for problems? Stop! Download the new AJAX search engine that makes
searching your log files as easy as surfing the web. DOWNLOAD SPLUNK!
http://ads.osdn.com/?ad_id=7637&alloc_id=16865&op=click
_______________________________________________
acpi-bugzilla mailing list
[email protected]
https://lists.sourceforge.net/lists/listinfo/acpi-bugzilla
