http://bugzilla.kernel.org/show_bug.cgi?id=6108
Summary: Failure of r8169 ethernet i/f after resume from S3 sleep
Kernel Version: 2.6.15.3
Status: NEW
Severity: normal
Owner: [EMAIL PROTECTED]
Submitter: [EMAIL PROTECTED]
CC: [EMAIL PROTECTED]
Most recent kernel where this bug did not occur: Unknown
Distribution: Debian unstable
Hardware Environment: Gigabyte GA-8IPE1000-G motherboard with RTL8169 GigE on
board. Realtek 8139 100baseT ethernet PCI card activiated as well (but no
cable connected).
Software Environment: 2.6.15.3 kernel with ACPI patch 20050902-2.6.15.diff,
DSDT repaired to compile cleanly with iasl. nvidia and USB modules removed
before testing. Shutdown to single user mode before testing. R8169_DEBUG
defined in r8169.c to print debugging info.
Problem Description:
On resume from S3 sleep state, r8169 ethernet interface will not respond.
Steps to reproduce:
telinit 1
rmmod nvidia ehci_hcd
echo -n mem >/sys/power/state
Push power button to resume
Network will no longer work
Relevant files (I hope!):
dmesg output:
kernel code, 12076k reserved, 653k data, 160k init, 131008k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 3033.57 BogoMIPS (lpj=6067144)
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 3febfbff 00000000 00000000 00000000
00000000 00000000 00000000
CPU: After vendor identify, caps: 3febfbff 00000000 00000000 00000000 00000000
00000000 00000000
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 256K
CPU: After all inits, caps: 3febfbff 00000000 00000000 00000080 00000000
00000000 00000000
mtrr: v2.0 (20020519)
CPU: Intel(R) Pentium(R) 4 CPU 1.50GHz stepping 02
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
tbget-0284: *** Info: Table [DSDT] replaced by host OS
tbxface-0109 [02] load_tables : ACPI Tables successfully acquired
Parsing all Control
Methods:.......................................................................
............................................................................
Table [DSDT](id 0005) - 561 Objects with 54 Devices 147 Methods 25 Regions
ACPI Namespace successfully loaded at root c03dc5dc
ACPI: setting ELCR to 0200 (from 0eb8)
evxfevnt-0091 [03] enable : Transition to ACPI mode successful
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfb040, last bus=2
PCI: Using configuration type 1
ACPI: Subsystem revision 20050902
evgpeblk-0988 [06] ev_create_gpe_block : GPE 00 to 1F [_GPE] 4 regs on int
0x9
evgpeblk-0996 [06] ev_create_gpe_block : Found 6 Wake, Enabled 0 Runtime
GPEs in this block
Completing Region/Field/Buffer/Package
initialization:................................................................
Initialized 24/25 Regions 9/9 Fields 21/21 Buffers 10/10 Packages (570 nodes)
Executing all Device _STA and_INI
methods:...........................................................
59 Devices found containing: 59 _STA, 2 _INI methods
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
PCI quirk: region 1000-107f claimed by ICH4 ACPI/GPIO/TCO
PCI quirk: region 1080-10bf claimed by ICH4 GPIO
PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
Boot video device is 0000:01:00.0
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs *3 4 5 6 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 *7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK1] (IRQs 3 *4 5 6 7 9 10 11 12 14 15)
SCSI subsystem initialized
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
PCI: Bridge: 0000:00:01.0
IO window: disabled.
MEM window: f8000000-f9ffffff
PREFETCH window: f0000000-f7ffffff
PCI: Bridge: 0000:00:1e.0
IO window: 9000-afff
MEM window: fa000000-fbffffff
PREFETCH window: 50000000-500fffff
PCI: Setting latency timer of device 0000:00:1e.0 to 64
highmem bounce pool size: 64 pages
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
ACPI: Power Button (FF) [PWRF]
ACPI: Power Button (CM) [PWRB]
ACPI: Fan [FAN] (on)
acpi_processor-0507 [06] processor_get_info : Error getting cpuindex for
acpiid 0x1
ACPI: Thermal Zone [THRM] (22 C)
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH5: IDE controller at PCI slot 0000:00:1f.1
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 11
PCI: setting IRQ 11 as level-triggered
ACPI: PCI Interrupt 0000:00:1f.1[A] -> Link [LNKC] -> GSI 11 (level, low) ->
IRQ 11
ICH5: chipset revision 2
ICH5: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:DMA, hdd:DMA
Probing IDE interface ide0...
hda: Maxtor 6Y080L0, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: Maxtor 6Y080L0, ATA DISK drive
hdd: LTN526D, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
SiI680: IDE controller at PCI slot 0000:02:01.0
ACPI: PCI Interrupt Link [LNKF] enabled at IRQ 10
PCI: setting IRQ 10 as level-triggered
ACPI: PCI Interrupt 0000:02:01.0[A] -> Link [LNKF] -> GSI 10 (level, low) ->
IRQ 10
SiI680: chipset revision 2
SiI680: BASE CLOCK == 133
SiI680: 100% native mode on irq 10
ide2: MMIO-DMA , BIOS settings: hde:pio, hdf:pio
ide3: MMIO-DMA , BIOS settings: hdg:pio, hdh:pio
Probing IDE interface ide2...
Probing IDE interface ide3...
hdg: Maxtor 6Y120L0, ATA DISK drive
ide3 at 0xf88100c0-0xf88100c7,0xf88100ca on irq 10
Probing IDE interface ide2...
hda: max request size: 128KiB
hda: Host Protected Area detected.
current capacity is 160084415 sectors (81963 MB)
native capacity is 160086528 sectors (81964 MB)
hda: Host Protected Area disabled.
hda: 160086528 sectors (81964 MB) w/2048KiB Cache, CHS=65535/16/63, UDMA(100)
hda: cache flushes supported
hda: hda1 hda2 hda3
hdc: max request size: 128KiB
hdc: 160086528 sectors (81964 MB) w/2048KiB Cache, CHS=65535/16/63, UDMA(100)
hdc: cache flushes supported
hdc: hdc1 hdc2 hdc3
hdg: max request size: 64KiB
hdg: 240121728 sectors (122942 MB) w/2048KiB Cache, CHS=65535/16/63, UDMA(133)
hdg: cache flushes supported
hdg: hdg1 hdg2 hdg3 < hdg5 hdg6 hdg7 >
libata version 1.20 loaded.
ata_piix 0000:00:1f.2: version 1.05
ACPI: PCI Interrupt 0000:00:1f.2[A] -> Link [LNKC] -> GSI 11 (level, low) ->
IRQ 11
PCI: Setting latency timer of device 0000:00:1f.2 to 64
ata1: SATA max UDMA/133 cmd 0xC000 ctl 0xC402 bmdma 0xD000 irq 11
ata2: SATA max UDMA/133 cmd 0xC800 ctl 0xCC02 bmdma 0xD008 irq 11
ata1: dev 0 cfg 49:2f00 82:346b 83:5b01 84:4003 85:3468 86:1801 87:4003 88:207f
ata1: dev 0 ATA-6, max UDMA/133, 58631231 sectors: LBA
ata1(0): applying bridge limits
ata1: dev 0 configured for UDMA/100
scsi0 : ata_piix
ata2: dev 0 cfg 49:2f00 82:346b 83:7d01 84:4003 85:3468 86:3c01 87:4003 88:207f
ata2: dev 0 ATA-6, max UDMA/133, 156301488 sectors: LBA48
ata2: dev 0 configured for UDMA/133
scsi1 : ata_piix
Vendor: ATA Model: ST330013AS Rev: 3.01
Type: Direct-Access ANSI SCSI revision: 05
Vendor: ATA Model: ST380817AS Rev: 3.42
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sda: 58631231 512-byte hdwr sectors (30019 MB)
SCSI device sda: drive cache: write back
SCSI device sda: 58631231 512-byte hdwr sectors (30019 MB)
SCSI device sda: drive cache: write back
sda: sda1 sda2
sd 0:0:0:0: Attached scsi disk sda
SCSI device sdb: 156301488 512-byte hdwr sectors (80026 MB)
SCSI device sdb: drive cache: write back
SCSI device sdb: 156301488 512-byte hdwr sectors (80026 MB)
SCSI device sdb: drive cache: write back
sdb: sdb1 sdb2
sd 1:0:0:0: Attached scsi disk sdb
md: raid0 personality registered as nr 2
md: raid5 personality registered as nr 4
raid5: automatically using best checksumming function: pIII_sse
pIII_sse : 1983.000 MB/sec
raid5: using function: pIII_sse (1983.000 MB/sec)
md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: bitmap version 4.39
NET: Registered protocol family 2
input: AT Translated Set 2 keyboard as /class/input/input0
IP route cache hash table entries: 65536 (order: 6, 262144 bytes)
TCP established hash table entries: 262144 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
TCP: Hash tables configured (established 262144 bind 65536)
TCP reno registered
TCP bic registered
Using IPI Shortcut mode
ACPI wakeup devices:
PCI0 HUB0 USB0 USB1 USB2 USB3 USBE
ACPI: (supports S0 S3 S4 S5)
md: Autodetecting RAID arrays.
md: autorun ...
md: considering sdb2 ...
md: adding sdb2 ...
md: adding hdg5 ...
md: hdg1 has different UUID to sdb2
md: adding hdc3 ...
md: hdc1 has different UUID to sdb2
md: adding hda3 ...
md: hda1 has different UUID to sdb2
md: created md1
md: bind<hda3>
md: bind<hdc3>
md: bind<hdg5>
md: bind<sdb2>
md: running: <sdb2><hdg5><hdc3><hda3>
raid5: device sdb2 operational as raid disk 3
raid5: device hdg5 operational as raid disk 2
raid5: device hdc3 operational as raid disk 1
raid5: device hda3 operational as raid disk 0
raid5: allocated 4195kB for md1
raid5: raid level 5 set md1 active with 4 out of 4 devices, algorithm 2
RAID5 conf printout:
--- rd:4 wd:4 fd:0
disk 0, o:1, dev:hda3
disk 1, o:1, dev:hdc3
disk 2, o:1, dev:hdg5
disk 3, o:1, dev:sdb2
md: considering hdg1 ...
md: adding hdg1 ...
md: adding hdc1 ...
md: adding hda1 ...
md: created md0
md: bind<hda1>
md: bind<hdc1>
md: bind<hdg1>
md: running: <hdg1><hdc1><hda1>
md0: setting max_sectors to 128, segment boundary to 32767
raid0: looking at hdg1
raid0: comparing hdg1(1951744) with hdg1(1951744)
raid0: END
raid0: ==> UNIQUE
raid0: 1 zones
raid0: looking at hdc1
raid0: comparing hdc1(1951744) with hdg1(1951744)
raid0: EQUAL
raid0: looking at hda1
raid0: comparing hda1(1951744) with hdg1(1951744)
raid0: EQUAL
raid0: FINAL 1 zones
raid0: done.
raid0 : md_size is 5855232 blocks.
raid0 : conf->hash_spacing is 5855232 blocks.
raid0 : nb_zone is 1.
raid0 : Allocating 4 bytes for hash.
md: ... autorun DONE.
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 160k freed
NET: Registered protocol family 1
usbcore: registered new driver usbfs
usbcore: registered new driver hub
hdd: ATAPI 52X CD-ROM drive, 120kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
USB Universal Host Controller Interface driver v2.3
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 5
PCI: setting IRQ 5 as level-triggered
ACPI: PCI Interrupt 0000:00:1d.0[A] -> Link [LNKA] -> GSI 5 (level, low) ->
IRQ 5
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:1d.0: irq 5, io base 0x0000bc00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 9
PCI: setting IRQ 9 as level-triggered
ACPI: PCI Interrupt 0000:00:1d.1[B] -> Link [LNKD] -> GSI 9 (level, low) ->
IRQ 9
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.1: irq 9, io base 0x0000b000
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.2[C] -> Link [LNKC] -> GSI 11 (level, low) ->
IRQ 11
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.2: irq 11, io base 0x0000b400
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.3[A] -> Link [LNKA] -> GSI 5 (level, low) ->
IRQ 5
PCI: Setting latency timer of device 0000:00:1d.3 to 64
uhci_hcd 0000:00:1d.3: UHCI Host Controller
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.3: irq 5, io base 0x0000b800
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
acpi_bus-0201 [01] bus_set_power : Device is not power manageable
ACPI: PCI Interrupt Link [LNK1] enabled at IRQ 4
PCI: setting IRQ 4 as level-triggered
ACPI: PCI Interrupt 0000:00:1d.7[D] -> Link [LNK1] -> GSI 4 (level, low) ->
IRQ 4
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
PCI: cache line size of 128 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5
ehci_hcd 0000:00:1d.7: irq 4, io mem 0xfc000000
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 8 ports detected
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 3
PCI: setting IRQ 3 as level-triggered
ACPI: PCI Interrupt 0000:00:1f.5[B] -> Link [LNKB] -> GSI 3 (level, low) ->
IRQ 3
PCI: Setting latency timer of device 0000:00:1f.5 to 64
mice: PS/2 mouse device common for all mice
intel8x0_measure_ac97_clock: measured 54181 usecs
intel8x0: clocking to 48000
r8169 Gigabit Ethernet driver 2.2LK-NAPI loaded
ACPI: PCI Interrupt Link [LNKE] enabled at IRQ 7
PCI: setting IRQ 7 as level-triggered
ACPI: PCI Interrupt 0000:02:09.0[A] -> Link [LNKE] -> GSI 7 (level, low) ->
IRQ 7
r8169: mac_version == RTL_GIGA_MAC_VER_E (0002)
r8169: phy_version == RTL_GIGA_PHY_VER_E (0000)
eth0: Identified chip type is 'RTL8169s/8110s'.
eth0: RTL8169 at 0xf887a000, 00:0f:ea:e4:ea:3d, IRQ 7
r8169: mac_version == RTL_GIGA_MAC_VER_E (0002)
r8169: phy_version == RTL_GIGA_PHY_VER_E (0000)
r8169: MAC version != 0 && PHY version == 0 or 1
r8169: Do final_reg2.cfg
r8169: Set MAC Reg C+CR Offset 0x82h = 0x01h
input: GenPS/2 Genius <NULL> as /class/input/input1
8139too Fast Ethernet driver 0.9.27
ACPI: PCI Interrupt 0000:02:03.0[A] -> Link [LNKA] -> GSI 5 (level, low) ->
IRQ 5
eth1: RealTek RTL8139 at 0xf88c4000, 00:50:ba:60:39:89, IRQ 5
eth1: Identified 8139 chip type 'RTL-8139C'
Adding 489972k swap on /dev/hda2. Priority:-1 extents:1 across:489972k
Adding 489972k swap on /dev/hdc2. Priority:-2 extents:1 across:489972k
Adding 489972k swap on /dev/hdg2. Priority:-3 extents:1 across:489972k
Adding 498004k swap on /dev/sda1. Priority:-4 extents:1 across:498004k
Adding 489940k swap on /dev/sdb1. Priority:-5 extents:1 across:489940k
EXT3 FS on sda2, internal journal
nvidia: module license 'NVIDIA' taints kernel.
ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [LNKA] -> GSI 5 (level, low) ->
IRQ 5
NVRM: loading NVIDIA Linux x86 NVIDIA Kernel Module 1.0-8178 Wed Dec 14
16:22:51 PST 2005
kjournald starting. Commit interval 5 seconds
EXT3 FS on md1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on hdg6, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on md0, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on hdg7, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
eth1: link down
NET: Registered protocol family 17
r8169: <6>r8169: Set MAC Reg C+CR Offset 0xE0. Bit-3 and bit-14 MUST be 1
r8169: eth0: link up
lspci output:
0000:00:00.0 Host bridge: Intel Corporation 82865G/PE/P DRAM Controller/Host-
Hub Interface (rev 02)
0000:00:01.0 PCI bridge: Intel Corporation 82865G/PE/P PCI to AGP Controller
(rev 02)
0000:00:1d.0 USB Controller: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB
UHCI Controller #1 (rev 02)
0000:00:1d.1 USB Controller: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB
UHCI Controller #2 (rev 02)
0000:00:1d.2 USB Controller: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB
UHCI Controller #3 (rev 02)
0000:00:1d.3 USB Controller: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB
UHCI Controller #4 (rev 02)
0000:00:1d.7 USB Controller: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB2
EHCI Controller (rev 02)
0000:00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev c2)
0000:00:1f.0 ISA bridge: Intel Corporation 82801EB/ER (ICH5/ICH5R) LPC
Interface Bridge (rev 02)
0000:00:1f.1 IDE interface: Intel Corporation 82801EB/ER (ICH5/ICH5R) IDE
Controller (rev 02)
0000:00:1f.2 IDE interface: Intel Corporation 82801EB (ICH5) SATA Controller
(rev 02)
0000:00:1f.3 SMBus: Intel Corporation 82801EB/ER (ICH5/ICH5R) SMBus Controller
(rev 02)
0000:00:1f.5 Multimedia audio controller: Intel Corporation 82801EB/ER
(ICH5/ICH5R) AC'97 Audio Controller (rev 02)
0000:01:00.0 VGA compatible controller: nVidia Corporation NV34 [GeForce FX
5200] (rev a1)
0000:02:01.0 Mass storage controller: Silicon Image, Inc. PCI0680 Ultra ATA-
133 Host Controller (rev 02)
0000:02:03.0 Ethernet controller: D-Link System Inc RTL8139 Ethernet (rev 10)
0000:02:09.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8169
Gigabit Ethernet (rev 10)
lsmod output (after modules removed):
Module Size Used by
af_packet 16136 0
evdev 7680 0
8139too 21248 0
r8169 25736 0
snd_intel8x0 28700 0
snd_ac97_codec 90016 1 snd_intel8x0
snd_ac97_bus 1920 1 snd_ac97_codec
snd_pcm 75272 2 snd_intel8x0,snd_ac97_codec
snd_timer 19460 1 snd_pcm
snd 43876 4 snd_intel8x0,snd_ac97_codec,snd_pcm,snd_timer
soundcore 7264 1 snd
snd_page_alloc 8328 2 snd_intel8x0,snd_pcm
usbcore 110212 1
unix 21808 0
/proc/interrupts:
CPU0
0: 82397 XT-PIC timer
1: 297 XT-PIC i8042
2: 0 XT-PIC cascade
3: 0 XT-PIC Intel ICH5
4: 0 XT-PIC ehci_hcd:usb5
5: 19061 XT-PIC uhci_hcd:usb1, uhci_hcd:usb4, eth1, nvidia
7: 439 XT-PIC eth0
9: 0 XT-PIC acpi, uhci_hcd:usb2
10: 1828 XT-PIC ide3
11: 5766 XT-PIC libata, uhci_hcd:usb3
12: 10135 XT-PIC i8042
14: 428 XT-PIC ide0
15: 420 XT-PIC ide1
NMI: 0
LOC: 82354
ERR: 0
ifconfig output (after resume when eth0 is not working):
eth0 Link encap:Ethernet HWaddr 00:0F:EA:E4:EA:3D
inet addr:192.168.0.3 Bcast:192.168.0.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:3806 errors:0 dropped:4294967292 overruns:0 frame:0
TX packets:2459 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:1888685 (1.8 MiB) TX bytes:671499 (655.7 KiB)
Interrupt:7 Base address:0x4000
eth1 Link encap:Ethernet HWaddr 00:50:BA:60:39:89
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
Interrupt:5 Base address:0x6000
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:144 errors:0 dropped:0 overruns:0 frame:0
TX packets:144 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:9648 (9.4 KiB) TX bytes:9648 (9.4 KiB)
------- You are receiving this mail because: -------
You are the assignee for the bug, or are watching the assignee.
-------------------------------------------------------
This SF.net email is sponsored by: Splunk Inc. Do you grep through log files
for problems? Stop! Download the new AJAX search engine that makes
searching your log files as easy as surfing the web. DOWNLOAD SPLUNK!
http://sel.as-us.falkag.net/sel?cmd=lnk&kid=103432&bid=230486&dat=121642
_______________________________________________
acpi-bugzilla mailing list
[email protected]
https://lists.sourceforge.net/lists/listinfo/acpi-bugzilla
