http://bugzilla.kernel.org/show_bug.cgi?id=6433
Summary: Kernel dump with CPU over-temperature alarm
Kernel Version: 2.6.16.9
Status: NEW
Severity: high
Owner: [EMAIL PROTECTED]
Submitter: [EMAIL PROTECTED]
Most recent kernel where this bug did not occur:
Only tested with 2.6.16.9
Distribution:
Debian Sarge with updated 2.6.16.9 kernel
Hardware Environment:
Abit LG-81 with 4xSATA drives
Software Environment:
No applications running
Problem Description:
If I set the CPU high temperature limit too low in lm-sensors (e.g. 25C) then I
get two problems:
- I get a kernel dump (see attached dmesg log) from kacpid
- The machine runs VERY slowly (~5secs to respond to CR on an SSH prompt)
If I restore a higher CPU temperature limit in lm-sensors (e.g. 65C) then the
problems immediately clear.
If I run the kernel without ACPI and repeat the above test, then I get no kernel
dump and the machine doesn't slow down. I do, however, get a beeping sound from
the motherboard when the "over-temperature" condition exists.
If I remove the "thermal" module and repeat the above test, then I get no kernel
dump, but the machine does run slowly as described above.
I have tried recompiling the k83627ehf module to disable the OVT# and SMI#
outputs, following a suggestion from the lm-sensors mailing list, but it makes
no difference. I still get the kernel dump and the slow operation.
Steps to reproduce:
Install 2.6.16.9 on the LG-81 motherboard.
modprobe k83627ehf
cp /etc/sensors.conf /etc/sensors-low.conf
Modify /etc/sensors-low.conf to set a low value for temp2_high (e.g. 25C)
sensors -s -c /etc/sensors-low.conf
The problem immediately occurs.
sensors -s -c /etc/sensors.conf
The problem immediately clears.
The requested outputs from debug utilities follow. Sorry that this is so much,
but this is what it says that I should post...
<DMESG>
Real Time Clock Driver v1.12ac
input: PC Speaker as /class/input/input1
ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 193
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.2: irq 193, io base 0x0000fc00
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 16 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:00:1d.3 to 64
uhci_hcd 0000:00:1d.3: UHCI Host Controller
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.3: irq 169, io base 0x0000fb00
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 209
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
PCI: cache line size of 128 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5
ehci_hcd 0000:00:1d.7: irq 209, io mem 0xfdfff000
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 8 ports detected
tg3.c:v3.49 (Feb 2, 2006)
ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:01:00.0 to 64
eth0: Tigon3 [partno(BCM95789) rev 4101 PHY(5750)] (PCI Express)
10/100/1000BaseT Ethernet 00:50:8d:7c:5e:5c
eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] Split[0] WireSpeed[1] TSOcap[1]
eth0: dma_rwctrl[76180000] dma_mask[64-bit]
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE]
input: ImExPS/2 Generic Explorer Mouse as /class/input/input2
md: md0 stopped.
md: bind<sdb1>
md: bind<sdc1>
md: bind<sdd1>
md: bind<sda1>
raid5: device sda1 operational as raid disk 0
raid5: device sdd1 operational as raid disk 3
raid5: device sdc1 operational as raid disk 2
raid5: device sdb1 operational as raid disk 1
raid5: allocated 4202kB for md0
raid5: raid level 5 set md0 active with 4 out of 4 devices, algorithm 2
RAID5 conf printout:
--- rd:4 wd:4 fd:0
disk 0, o:1, dev:sda1
disk 1, o:1, dev:sdb1
disk 2, o:1, dev:sdc1
disk 3, o:1, dev:sdd1
nbd0: Attempted send on closed socket
end_request: I/O error, dev nbd0, sector 0
Buffer I/O error on device nbd0, logical block 0
Buffer I/O error on device nbd0, logical block 1
Buffer I/O error on device nbd0, logical block 2
Buffer I/O error on device nbd0, logical block 3
Buffer I/O error on device nbd0, logical block 4
Buffer I/O error on device nbd0, logical block 5
Buffer I/O error on device nbd0, logical block 6
Buffer I/O error on device nbd0, logical block 7
nbd0: Attempted send on closed socket
end_request: I/O error, dev nbd0, sector 0
Buffer I/O error on device nbd0, logical block 0
nbd0: Attempted send on closed socket
end_request: I/O error, dev nbd0, sector 4294965120
Buffer I/O error on device nbd0, logical block 536870640
nbd0: Attempted send on closed socket
end_request: I/O error, dev nbd0, sector 4294965120
nbd0: Attempted send on closed socket
end_request: I/O error, dev nbd0, sector 0
nbd1: Attempted send on closed socket
end_request: I/O error, dev nbd1, sector 4294965120
nbd1: Attempted send on closed socket
end_request: I/O error, dev nbd1, sector 4294965120
nbd1: Attempted send on closed socket
end_request: I/O error, dev nbd1, sector 0
nbd1: Attempted send on closed socket
end_request: I/O error, dev nbd1, sector 0
nbd2: Attempted send on closed socket
end_request: I/O error, dev nbd2, sector 4294965120
nbd2: Attempted send on closed socket
end_request: I/O error, dev nbd2, sector 4294965120
nbd2: Attempted send on closed socket
end_request: I/O error, dev nbd2, sector 0
nbd2: Attempted send on closed socket
end_request: I/O error, dev nbd2, sector 0
nbd3: Attempted send on closed socket
end_request: I/O error, dev nbd3, sector 4294965120
nbd3: Attempted send on closed socket
end_request: I/O error, dev nbd3, sector 4294965120
nbd3: Attempted send on closed socket
end_request: I/O error, dev nbd3, sector 0
nbd3: Attempted send on closed socket
end_request: I/O error, dev nbd3, sector 0
nbd4: Attempted send on closed socket
end_request: I/O error, dev nbd4, sector 4294965120
nbd4: Attempted send on closed socket
end_request: I/O error, dev nbd4, sector 4294965120
nbd4: Attempted send on closed socket
end_request: I/O error, dev nbd4, sector 0
nbd4: Attempted send on closed socket
end_request: I/O error, dev nbd4, sector 0
nbd5: Attempted send on closed socket
end_request: I/O error, dev nbd5, sector 4294965120
nbd5: Attempted send on closed socket
end_request: I/O error, dev nbd5, sector 4294965120
nbd5: Attempted send on closed socket
end_request: I/O error, dev nbd5, sector 0
nbd5: Attempted send on closed socket
end_request: I/O error, dev nbd5, sector 0
nbd6: Attempted send on closed socket
end_request: I/O error, dev nbd6, sector 4294965120
nbd6: Attempted send on closed socket
end_request: I/O error, dev nbd6, sector 4294965120
nbd6: Attempted send on closed socket
end_request: I/O error, dev nbd6, sector 0
nbd6: Attempted send on closed socket
end_request: I/O error, dev nbd6, sector 0
nbd7: Attempted send on closed socket
end_request: I/O error, dev nbd7, sector 4294965120
nbd7: Attempted send on closed socket
end_request: I/O error, dev nbd7, sector 4294965120
nbd7: Attempted send on closed socket
end_request: I/O error, dev nbd7, sector 0
nbd7: Attempted send on closed socket
end_request: I/O error, dev nbd7, sector 0
nbd8: Attempted send on closed socket
end_request: I/O error, dev nbd8, sector 4294965120
nbd8: Attempted send on closed socket
end_request: I/O error, dev nbd8, sector 4294965120
nbd8: Attempted send on closed socket
end_request: I/O error, dev nbd8, sector 0
nbd8: Attempted send on closed socket
end_request: I/O error, dev nbd8, sector 0
nbd9: Attempted send on closed socket
end_request: I/O error, dev nbd9, sector 4294965120
nbd9: Attempted send on closed socket
end_request: I/O error, dev nbd9, sector 4294965120
nbd9: Attempted send on closed socket
end_request: I/O error, dev nbd9, sector 0
nbd9: Attempted send on closed socket
end_request: I/O error, dev nbd9, sector 0
nbd10: Attempted send on closed socket
end_request: I/O error, dev nbd10, sector 4294965120
nbd10: Attempted send on closed socket
end_request: I/O error, dev nbd10, sector 4294965120
nbd10: Attempted send on closed socket
end_request: I/O error, dev nbd10, sector 0
nbd10: Attempted send on closed socket
end_request: I/O error, dev nbd10, sector 0
nbd11: Attempted send on closed socket
end_request: I/O error, dev nbd11, sector 4294965120
nbd11: Attempted send on closed socket
end_request: I/O error, dev nbd11, sector 4294965120
nbd11: Attempted send on closed socket
end_request: I/O error, dev nbd11, sector 0
nbd11: Attempted send on closed socket
end_request: I/O error, dev nbd11, sector 0
nbd12: Attempted send on closed socket
end_request: I/O error, dev nbd12, sector 4294965120
nbd12: Attempted send on closed socket
end_request: I/O error, dev nbd12, sector 4294965120
nbd12: Attempted send on closed socket
end_request: I/O error, dev nbd12, sector 0
nbd12: Attempted send on closed socket
end_request: I/O error, dev nbd12, sector 0
nbd13: Attempted send on closed socket
end_request: I/O error, dev nbd13, sector 4294965120
nbd13: Attempted send on closed socket
end_request: I/O error, dev nbd13, sector 4294965120
nbd13: Attempted send on closed socket
end_request: I/O error, dev nbd13, sector 0
nbd13: Attempted send on closed socket
end_request: I/O error, dev nbd13, sector 0
nbd14: Attempted send on closed socket
end_request: I/O error, dev nbd14, sector 4294965120
nbd14: Attempted send on closed socket
end_request: I/O error, dev nbd14, sector 4294965120
nbd14: Attempted send on closed socket
end_request: I/O error, dev nbd14, sector 0
nbd14: Attempted send on closed socket
end_request: I/O error, dev nbd14, sector 0
nbd15: Attempted send on closed socket
end_request: I/O error, dev nbd15, sector 4294965120
nbd15: Attempted send on closed socket
end_request: I/O error, dev nbd15, sector 4294965120
nbd15: Attempted send on closed socket
end_request: I/O error, dev nbd15, sector 0
nbd15: Attempted send on closed socket
end_request: I/O error, dev nbd15, sector 0
ReiserFS: dm-0: found reiserfs format "3.6" with standard journal
ReiserFS: dm-0: using ordered data mode
ReiserFS: dm-0: journal params: device dm-0, size 8192, journal first block 18,
max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: dm-0: checking transaction log (dm-0)
ReiserFS: dm-0: Using r5 hash to sort names
nbd0: Attempted send on closed socket
end_request: I/O error, dev nbd0, sector 0
printk: 62 messages suppressed.
Buffer I/O error on device nbd0, logical block 0
Buffer I/O error on device nbd0, logical block 1
nbd0: Attempted send on closed socket
end_request: I/O error, dev nbd0, sector 0
nbd0: Attempted send on closed socket
end_request: I/O error, dev nbd0, sector 0
nbd1: Attempted send on closed socket
end_request: I/O error, dev nbd1, sector 0
nbd2: Attempted send on closed socket
end_request: I/O error, dev nbd2, sector 0
nbd3: Attempted send on closed socket
end_request: I/O error, dev nbd3, sector 0
nbd4: Attempted send on closed socket
end_request: I/O error, dev nbd4, sector 0
nbd5: Attempted send on closed socket
end_request: I/O error, dev nbd5, sector 0
nbd6: Attempted send on closed socket
end_request: I/O error, dev nbd6, sector 0
nbd7: Attempted send on closed socket
end_request: I/O error, dev nbd7, sector 0
nbd8: Attempted send on closed socket
end_request: I/O error, dev nbd8, sector 0
nbd9: Attempted send on closed socket
end_request: I/O error, dev nbd9, sector 0
nbd10: Attempted send on closed socket
end_request: I/O error, dev nbd10, sector 0
nbd11: Attempted send on closed socket
end_request: I/O error, dev nbd11, sector 0
nbd12: Attempted send on closed socket
end_request: I/O error, dev nbd12, sector 0
nbd13: Attempted send on closed socket
end_request: I/O error, dev nbd13, sector 0
nbd14: Attempted send on closed socket
end_request: I/O error, dev nbd14, sector 0
nbd15: Attempted send on closed socket
end_request: I/O error, dev nbd15, sector 0
nbd0: Attempted send on closed socket
end_request: I/O error, dev nbd0, sector 0
nbd1: Attempted send on closed socket
end_request: I/O error, dev nbd1, sector 0
nbd2: Attempted send on closed socket
end_request: I/O error, dev nbd2, sector 0
nbd3: Attempted send on closed socket
end_request: I/O error, dev nbd3, sector 0
nbd4: Attempted send on closed socket
end_request: I/O error, dev nbd4, sector 0
nbd5: Attempted send on closed socket
end_request: I/O error, dev nbd5, sector 0
nbd6: Attempted send on closed socket
end_request: I/O error, dev nbd6, sector 0
nbd7: Attempted send on closed socket
end_request: I/O error, dev nbd7, sector 0
nbd8: Attempted send on closed socket
end_request: I/O error, dev nbd8, sector 0
nbd9: Attempted send on closed socket
end_request: I/O error, dev nbd9, sector 0
nbd10: Attempted send on closed socket
end_request: I/O error, dev nbd10, sector 0
nbd11: Attempted send on closed socket
end_request: I/O error, dev nbd11, sector 0
nbd12: Attempted send on closed socket
end_request: I/O error, dev nbd12, sector 0
nbd13: Attempted send on closed socket
end_request: I/O error, dev nbd13, sector 0
nbd14: Attempted send on closed socket
end_request: I/O error, dev nbd14, sector 0
nbd15: Attempted send on closed socket
end_request: I/O error, dev nbd15, sector 0
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
NET: Registered protocol family 17
tg3: eth0: Link is up at 1000 Mbps, full duplex.
tg3: eth0: Flow control is on for TX and on for RX.
ACPI: Power Button (FF) [PWRF]
ACPI: Power Button (CM) [PWRB]
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
IPv6 over IPv4 tunneling driver
eth0: no IPv6 routers present
BUG: soft lockup detected on CPU#0!
Pid: 9, comm: kacpid
EIP: 0060:[<c0232e80>] CPU: 0
EIP is at acpi_ns_delete_namespace_by_owner+0x30/0x9c
EFLAGS: 00000286 Not tainted (2.6.16.9.rwl4rwl #1)
EAX: c146ba60 EBX: 00000000 ECX: c146ba60 EDX: c146ba60
ESI: c146ba80 EDI: 00000005 EBP: 00000000 DS: 007b ES: 007b
CR0: 8005003b CR2: 08128008 CR3: 1e768000 CR4: 000006d0
[<c0227346>] acpi_ds_terminate_control_method+0x95/0xeb
[<c0234d40>] acpi_ps_parse_aml+0x121/0x1f5
[<c0235cec>] acpi_ps_execute_pass+0x72/0x86
[<c0235c12>] acpi_ps_execute_method+0x54/0x7e
[<c0233100>] acpi_ns_execute_control_method+0x56/0x63
[<c0233096>] acpi_ns_evaluate_by_handle+0x74/0x88
[<c0232f95>] acpi_ns_evaluate_relative+0xa9/0xc5
[<c0232865>] acpi_evaluate_object+0x139/0x1fc
[<c02252fc>] acpi_os_release_object+0xd/0x12
[<c023b1df>] acpi_ut_acquire_mutex+0x2e/0x67
[<c0225643>] acpi_evaluate_integer+0x6b/0x93
[<e0033025>] acpi_thermal_get_temperature+0x25/0x36 [thermal]
[<e003360c>] acpi_thermal_check+0x21/0x232 [thermal]
[<e0034050>] acpi_thermal_notify+0x47/0x93 [thermal]
[<c0229b51>] acpi_ev_notify_dispatch+0x57/0x64
[<c022506b>] acpi_os_execute_deferred+0xe/0x1b
[<c0125c3f>] run_workqueue+0x5f/0xc0
[<c022505d>] acpi_os_execute_deferred+0x0/0x1b
[<c0125dc9>] worker_thread+0x129/0x150
[<c01152a0>] default_wake_function+0x0/0x20
[<c01152a0>] default_wake_function+0x0/0x20
[<c0125ca0>] worker_thread+0x0/0x150
[<c0128a67>] kthread+0xa7/0xb0
[<c01289c0>] kthread+0x0/0xb0
[<c010133d>] kernel_thread_helper+0x5/0x18
BUG: soft lockup detected on CPU#0!
Pid: 9, comm: kacpid
EIP: 0060:[<c0232e93>] CPU: 0
EIP is at acpi_ns_delete_namespace_by_owner+0x43/0x9c
EFLAGS: 00000282 Not tainted (2.6.16.9.rwl4rwl #1)
EAX: c146a980 EBX: c146a980 ECX: c146a980 EDX: c146a980
ESI: c146a9c0 EDI: 00000004 EBP: 00000000 DS: 007b ES: 007b
CR0: 8005003b CR2: b7ddb000 CR3: 1d0ba000 CR4: 000006d0
[<c0227346>] acpi_ds_terminate_control_method+0x95/0xeb
[<c0234d40>] acpi_ps_parse_aml+0x121/0x1f5
[<c0235cec>] acpi_ps_execute_pass+0x72/0x86
[<c0235c12>] acpi_ps_execute_method+0x54/0x7e
[<c0233100>] acpi_ns_execute_control_method+0x56/0x63
[<c0233096>] acpi_ns_evaluate_by_handle+0x74/0x88
[<c0232f95>] acpi_ns_evaluate_relative+0xa9/0xc5
[<c0232865>] acpi_evaluate_object+0x139/0x1fc
[<c02252fc>] acpi_os_release_object+0xd/0x12
[<c023b1df>] acpi_ut_acquire_mutex+0x2e/0x67
[<c0225643>] acpi_evaluate_integer+0x6b/0x93
[<e0033025>] acpi_thermal_get_temperature+0x25/0x36 [thermal]
[<e003360c>] acpi_thermal_check+0x21/0x232 [thermal]
[<e0034050>] acpi_thermal_notify+0x47/0x93 [thermal]
[<c0229b51>] acpi_ev_notify_dispatch+0x57/0x64
[<c022506b>] acpi_os_execute_deferred+0xe/0x1b
[<c0125c3f>] run_workqueue+0x5f/0xc0
[<c022505d>] acpi_os_execute_deferred+0x0/0x1b
[<c0125dc9>] worker_thread+0x129/0x150
[<c01152a0>] default_wake_function+0x0/0x20
[<c01152a0>] default_wake_function+0x0/0x20
[<c0125ca0>] worker_thread+0x0/0x150
[<c0128a67>] kthread+0xa7/0xb0
[<c01289c0>] kthread+0x0/0xb0
[<c010133d>] kernel_thread_helper+0x5/0x18
guppy:~#
<DMIDECODE>
# dmidecode 2.6
SMBIOS 2.3 present.
37 structures occupying 1080 bytes.
Table at 0x000F0000.
Handle 0x0000
DMI type 0, 20 bytes.
BIOS Information
Vendor: Phoenix Technologies, LTD
Version: 6.00 PG
Release Date: 06/06/2005
Address: 0xE0000
Runtime Size: 128 kB
ROM Size: 512 kB
Characteristics:
EISA is supported
PCI is supported
PNP is supported
APM is supported
BIOS is upgradeable
BIOS shadowing is allowed
Boot from CD is supported
Selectable boot is supported
BIOS ROM is socketed
EDD is supported
5.25"/360 KB floppy services are supported (int 13h)
5.25"/1.2 MB floppy services are supported (int 13h)
3.5"/720 KB floppy services are supported (int 13h)
3.5"/2.88 MB floppy services are supported (int 13h)
Print screen service is supported (int 5h)
8042 keyboard services are supported (int 9h)
Serial services are supported (int 14h)
Printer services are supported (int 17h)
CGA/mono video services are supported (int 10h)
ACPI is supported
USB legacy is supported
LS-120 boot is supported
ATAPI Zip drive boot is supported
BIOS boot specification is supported
Handle 0x0001
DMI type 1, 25 bytes.
System Information
Manufacturer:
Product Name:
Version:
Serial Number:
UUID: 00000000-0000-0000-0000-00508D7C5E5C
Wake-up Type: Power Switch
Handle 0x0002
DMI type 2, 8 bytes.
Base Board Information
Manufacturer: http://www.abit.com.tw/
Product Name: LG-81 (Intel LakePort-ICH7)
Version: 1.x
Serial Number:
Handle 0x0003
DMI type 3, 17 bytes.
Chassis Information
Manufacturer:
Type: Desktop
Lock: Not Present
Version:
Serial Number:
Asset Tag:
Boot-up State: Unknown
Power Supply State: Unknown
Thermal State: Unknown
Security Status: Unknown
OEM Information: 0x00000000
Handle 0x0004
DMI type 4, 35 bytes.
Processor Information
Socket Designation: Socket 775
Type: Central Processor
Family: Celeron
Manufacturer: Intel
ID: 49 0F 00 00 FF FB EB BF
Signature: Type 0, Family 15, Model 4, Stepping 9
Flags:
FPU (Floating-point unit on-chip)
VME (Virtual mode extension)
DE (Debugging extension)
PSE (Page size extension)
TSC (Time stamp counter)
MSR (Model specific registers)
PAE (Physical address extension)
MCE (Machine check exception)
CX8 (CMPXCHG8 instruction supported)
APIC (On-chip APIC hardware supported)
SEP (Fast system call)
MTRR (Memory type range registers)
PGE (Page global enable)
MCA (Machine check architecture)
CMOV (Conditional move instruction supported)
PAT (Page attribute table)
PSE-36 (36-bit page size extension)
CLFSH (CLFLUSH instruction supported)
DS (Debug store)
ACPI (ACPI supported)
MMX (MMX technology supported)
FXSR (Fast floating-point save and restore)
SSE (Streaming SIMD extensions)
SSE2 (Streaming SIMD extensions 2)
SS (Self-snoop)
HTT (Hyper-threading technology)
TM (Thermal monitor supported)
PBE (Pending break enabled)
Version: Intel(R) Celeron(R) CPU
Voltage: 1.3 V
External Clock: 135 MHz
Max Speed: 5000 MHz
Current Speed: 2700 MHz
Status: Populated, Enabled
Upgrade: ZIF Socket
L1 Cache Handle: 0x000A
L2 Cache Handle: 0x000B
L3 Cache Handle: Not Provided
Serial Number:
Asset Tag:
Part Number:
Handle 0x0005
DMI type 5, 24 bytes.
Memory Controller Information
Error Detecting Method: 8-bit Parity
Error Correcting Capabilities:
None
Supported Interleave: One-way Interleave
Current Interleave: One-way Interleave
Maximum Memory Module Size: 2048 MB
Maximum Total Memory Size: 8192 MB
Supported Speeds:
Other
Supported Memory Types:
Other
Memory Module Voltage: 5.0 V
Associated Memory Slots: 4
0x0006
0x0007
0x0008
0x0009
Enabled Error Correcting Capabilities:
None
Handle 0x0006
DMI type 6, 12 bytes.
Memory Module Information
Socket Designation: DIMM1
Bank Connections: 0
Current Speed: Unknown
Type: Other
Installed Size: 256 MB (Single-bank Connection)
Enabled Size: 256 MB (Single-bank Connection)
Error Status: OK
Handle 0x0007
DMI type 6, 12 bytes.
Memory Module Information
Socket Designation: DIMM2
Bank Connections: None
Current Speed: Unknown
Type: Unknown
Installed Size: Not Installed
Enabled Size: Not Installed
Error Status: OK
Handle 0x0008
DMI type 6, 12 bytes.
Memory Module Information
Socket Designation: A2
Bank Connections: 4
Current Speed: Unknown
Type: Other
Installed Size: 256 MB (Single-bank Connection)
Enabled Size: 256 MB (Single-bank Connection)
Error Status: OK
Handle 0x0009
DMI type 6, 12 bytes.
Memory Module Information
Socket Designation: A3
Bank Connections: None
Current Speed: Unknown
Type: Unknown
Installed Size: Not Installed
Enabled Size: Not Installed
Error Status: OK
Handle 0x000A
DMI type 7, 19 bytes.
Cache Information
Socket Designation:
Configuration: Enabled, Not Socketed, Level 1
Operational Mode: Write Back
Location: Internal
Installed Size: 32 KB
Maximum Size: 32 KB
Supported SRAM Types:
Synchronous
Installed SRAM Type: Synchronous
Speed: Unknown
Error Correction Type: Unknown
System Type: Unknown
Associativity: Unknown
Handle 0x000B
DMI type 7, 19 bytes.
Cache Information
Socket Designation:
Configuration: Enabled, Not Socketed, Level 2
Operational Mode: Write Back
Location: External
Installed Size: 256 KB
Maximum Size: 256 KB
Supported SRAM Types:
Synchronous
Installed SRAM Type: Synchronous
Speed: Unknown
Error Correction Type: Unknown
System Type: Unknown
Associativity: Unknown
Handle 0x000C
DMI type 8, 9 bytes.
Port Connector Information
Internal Reference Designator: IDE1
Internal Connector Type: On Board IDE
External Reference Designator: Not Specified
External Connector Type: None
Port Type: Other
Handle 0x000D
DMI type 8, 9 bytes.
Port Connector Information
Internal Reference Designator: FDC1
Internal Connector Type: On Board Floppy
External Reference Designator: Not Specified
External Connector Type: None
Port Type: 8251 FIFO Compatible
Handle 0x000E
DMI type 8, 9 bytes.
Port Connector Information
Internal Reference Designator:
Internal Connector Type: 9 Pin Dual Inline (pin 10 cut)
External Reference Designator: COM1
External Connector Type: DB-9 male
Port Type: Serial Port 16450 Compatible
Handle 0x000F
DMI type 8, 9 bytes.
Port Connector Information
Internal Reference Designator: LPT1
Internal Connector Type: DB-25 female
External Reference Designator:
External Connector Type: DB-25 female
Port Type: Parallel Port ECP/EPP
Handle 0x0010
DMI type 8, 9 bytes.
Port Connector Information
Internal Reference Designator:
Internal Connector Type: PS/2
External Reference Designator: KM1
External Connector Type: PS/2
Port Type: Keyboard Port
Handle 0x0011
DMI type 8, 9 bytes.
Port Connector Information
Internal Reference Designator:
Internal Connector Type: PS/2
External Reference Designator: KM1
External Connector Type: PS/2
Port Type: Mouse Port
Handle 0x0012
DMI type 8, 9 bytes.
Port Connector Information
Internal Reference Designator: Not Specified
Internal Connector Type: None
External Reference Designator: USB1
External Connector Type: Other
Port Type: USB
Handle 0x0013
DMI type 8, 9 bytes.
Port Connector Information
Internal Reference Designator: Not Specified
Internal Connector Type: None
External Reference Designator: USB2
External Connector Type: Other
Port Type: USB
Handle 0x0014
DMI type 9, 13 bytes.
System Slot Information
Designation: PCI1
Type: 32-bit PCI
Current Usage: Available
Length: Long
ID: 1
Characteristics:
5.0 V is provided
PME signal is supported
Handle 0x0015
DMI type 9, 13 bytes.
System Slot Information
Designation: PCI1
Type: 32-bit PCI
Current Usage: Available
Length: Long
ID: 2
Characteristics:
5.0 V is provided
PME signal is supported
Handle 0x0016
DMI type 9, 13 bytes.
System Slot Information
Designation: PCI2
Type: 32-bit PCI
Current Usage: Available
Length: Long
ID: 3
Characteristics:
5.0 V is provided
PME signal is supported
Handle 0x0017
DMI type 9, 13 bytes.
System Slot Information
Designation: PCI3
Type: 32-bit <OUT OF SPEC>
Current Usage: In Use
Length: Long
Characteristics:
5.0 V is provided
PME signal is supported
Handle 0x0018
DMI type 13, 22 bytes.
BIOS Language Information
Installable Languages: 3
n|US|iso8859-1
n|US|iso8859-1
r|CA|iso8859-1
Currently Installed Language: n|US|iso8859-1
Handle 0x0019
DMI type 16, 15 bytes.
Physical Memory Array
Location: System Board Or Motherboard
Use: System Memory
Error Correction Type: None
Maximum Capacity: 4 GB
Error Information Handle: Not Provided
Number Of Devices: 4
Handle 0x001A
DMI type 17, 27 bytes.
Memory Device
Array Handle: 0x0019
Error Information Handle: Not Provided
Total Width: 64 bits
Data Width: 64 bits
Size: 256 MB
Form Factor: DIMM
Set: None
Locator: DIMM1
Bank Locator: Bank0/1
Type: DDR
Type Detail: Synchronous
Speed: Unknown
Manufacturer: None
Serial Number: None
Asset Tag: None
Part Number: None
Handle 0x001B
DMI type 17, 27 bytes.
Memory Device
Array Handle: 0x0019
Error Information Handle: Not Provided
Total Width: Unknown
Data Width: Unknown
Size: No Module Installed
Form Factor: DIMM
Set: None
Locator: DIMM2
Bank Locator: Bank2/3
Type: Unknown
Type Detail: Unknown
Speed: Unknown
Manufacturer: None
Serial Number: None
Asset Tag: None
Part Number: None
Handle 0x001C
DMI type 17, 27 bytes.
Memory Device
Array Handle: 0x0019
Error Information Handle: Not Provided
Total Width: 64 bits
Data Width: 64 bits
Size: 256 MB
Form Factor: DIMM
Set: None
Locator: A2
Bank Locator: Bank4/5
Type: DDR
Type Detail: Synchronous
Speed: Unknown
Manufacturer: None
Serial Number: None
Asset Tag: None
Part Number: None
Handle 0x001D
DMI type 17, 27 bytes.
Memory Device
Array Handle: 0x0019
Error Information Handle: Not Provided
Total Width: Unknown
Data Width: Unknown
Size: No Module Installed
Form Factor: DIMM
Set: None
Locator: A3
Bank Locator: Bank6/7
Type: Unknown
Type Detail: Unknown
Speed: Unknown
Manufacturer: None
Serial Number: None
Asset Tag: None
Part Number: None
Handle 0x001E
DMI type 19, 15 bytes.
Memory Array Mapped Address
Starting Address: 0x00000000000
Ending Address: 0x0001FFFFFFF
Range Size: 512 MB
Physical Array Handle: 0x0019
Partition Width: 0
Handle 0x001F
DMI type 20, 19 bytes.
Memory Device Mapped Address
Starting Address: 0x00000000000
Ending Address: 0x0000FFFFFFF
Range Size: 256 MB
Physical Device Handle: 0x001A
Memory Array Mapped Address Handle: 0x001E
Partition Row Position: 1
Handle 0x0020
DMI type 20, 19 bytes.
Memory Device Mapped Address
Starting Address: 0x00000000000
Ending Address: 0x000000003FF
Range Size: 1 kB
Physical Device Handle: 0x001B
Memory Array Mapped Address Handle: 0x001E
Partition Row Position: 1
Handle 0x0021
DMI type 20, 19 bytes.
Memory Device Mapped Address
Starting Address: 0x00010000000
Ending Address: 0x0001FFFFFFF
Range Size: 256 MB
Physical Device Handle: 0x001C
Memory Array Mapped Address Handle: 0x001E
Partition Row Position: 1
Handle 0x0022
DMI type 20, 19 bytes.
Memory Device Mapped Address
Starting Address: 0x00000000000
Ending Address: 0x000000003FF
Range Size: 1 kB
Physical Device Handle: 0x001D
Memory Array Mapped Address Handle: 0x001E
Partition Row Position: 1
Handle 0x0023
DMI type 32, 11 bytes.
System Boot Information
Status: No errors detected
Handle 0x0024
DMI type 127, 4 bytes.
End Of Table
<LSPCI -VV>
0000:00:00.0 Host bridge: Intel Corp.: Unknown device 2770 (rev 02)
Subsystem: ABIT Computer Corp.: Unknown device 1064
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping-
SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ >SERR- <PERR-
Latency: 0
Capabilities: [e0] #09 [5109]
0000:00:02.0 VGA compatible controller: Intel Corp.: Unknown device 2772 (rev
02) (prog-if 00 [VGA])
Subsystem: ABIT Computer Corp.: Unknown device 1064
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping-
SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 10
Region 0: Memory at fdf00000 (32-bit, non-prefetchable) [size=512K]
Region 1: I/O ports at ff00 [size=8]
Region 2: Memory at d0000000 (32-bit, prefetchable) [size=256M]
Region 3: Memory at fdf80000 (32-bit, non-prefetchable) [size=256K]
Capabilities: [90] Message Signalled Interrupts: 64bit- Queue=0/0
Enable-
Address: 00000000 Data: 0000
Capabilities: [d0] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:1b.0 0403: Intel Corp.: Unknown device 27d8 (rev 01)
Subsystem: ABIT Computer Corp.: Unknown device 1064
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping-
SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 0x08 (32 bytes)
Interrupt: pin A routed to IRQ 10
Region 0: Memory at fdff8000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [60] Message Signalled Interrupts: 64bit+ Queue=0/0
Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [70] #10 [0091]
0000:00:1c.0 PCI bridge: Intel Corp.: Unknown device 27d0 (rev 01) (prog-if 00
[Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping-
SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 0x08 (32 bytes)
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: fdd00000-fddfffff
Prefetchable memory behind bridge: 00000000fde00000-00000000fde00000
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [40] #10 [0141]
Capabilities: [80] Message Signalled Interrupts: 64bit- Queue=0/0
Enable+
Address: fee00000 Data: 40b9
Capabilities: [90] #0d [0000]
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:1d.0 USB Controller: Intel Corp.: Unknown device 27c8 (rev 01) (prog-if
00 [UHCI])
Subsystem: ABIT Computer Corp.: Unknown device 1064
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping-
SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 209
Region 4: I/O ports at fe00 [size=32]
0000:00:1d.1 USB Controller: Intel Corp.: Unknown device 27c9 (rev 01) (prog-if
00 [UHCI])
Subsystem: ABIT Computer Corp.: Unknown device 1064
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping-
SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 201
Region 4: I/O ports at fd00 [size=32]
0000:00:1d.2 USB Controller: Intel Corp.: Unknown device 27ca (rev 01) (prog-if
00 [UHCI])
Subsystem: ABIT Computer Corp.: Unknown device 1064
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping-
SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin C routed to IRQ 193
Region 4: I/O ports at fc00 [size=32]
0000:00:1d.3 USB Controller: Intel Corp.: Unknown device 27cb (rev 01) (prog-if
00 [UHCI])
Subsystem: ABIT Computer Corp.: Unknown device 1064
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping-
SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin D routed to IRQ 169
Region 4: I/O ports at fb00 [size=32]
0000:00:1d.7 USB Controller: Intel Corp.: Unknown device 27cc (rev 01) (prog-if
20 [EHCI])
Subsystem: ABIT Computer Corp.: Unknown device 1064
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping-
SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 209
Region 0: Memory at fdfff000 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:1e.0 PCI bridge: Intel Corp. 82801 PCI Bridge (rev e1) (prog-if 01
[Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping-
SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=02, subordinate=02, sec-latency=32
I/O behind bridge: 0000e000-0000efff
Memory behind bridge: fdc00000-fdcfffff
Prefetchable memory behind bridge: 00000000fdb00000-00000000fdb00000
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [50] #0d [0000]
0000:00:1f.0 ISA bridge: Intel Corp.: Unknown device 27b8 (rev 01)
Subsystem: ABIT Computer Corp.: Unknown device 1064
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping-
SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Capabilities: [e0] #09 [100c]
0000:00:1f.1 IDE interface: Intel Corp.: Unknown device 27df (rev 01) (prog-if
8a [Master SecP PriP])
Subsystem: ABIT Computer Corp.: Unknown device 1064
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping-
SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 193
Region 0: I/O ports at <unassigned>
Region 1: I/O ports at <unassigned>
Region 2: I/O ports at <unassigned>
Region 3: I/O ports at <unassigned>
Region 4: I/O ports at fa00 [size=16]
0000:00:1f.2 IDE interface: Intel Corp.: Unknown device 27c0 (rev 01) (prog-if
8f [Master SecP SecO PriP PriO])
Subsystem: ABIT Computer Corp.: Unknown device 1064
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping-
SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 201
Region 0: I/O ports at f900 [size=8]
Region 1: I/O ports at f800 [size=4]
Region 2: I/O ports at f700 [size=8]
Region 3: I/O ports at f600 [size=4]
Region 4: I/O ports at f500 [size=16]
Capabilities: [70] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:1f.3 SMBus: Intel Corp.: Unknown device 27da (rev 01)
Subsystem: ABIT Computer Corp.: Unknown device 1064
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping-
SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort-
<MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 11
Region 4: I/O ports at 0500 [size=32]
0000:01:00.0 Ethernet controller: Broadcom Corporation: Unknown device 169d
(rev 11)
Subsystem: ABIT Computer Corp.: Unknown device 1064
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping-
SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 0x08 (32 bytes)
Interrupt: pin A routed to IRQ 169
Region 0: Memory at fddf0000 (64-bit, non-prefetchable) [size=64K]
Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [50] Vital Product Data
Capabilities: [58] Message Signalled Interrupts: 64bit+ Queue=0/3
Enable-
Address: 02049480a5006914 Data: 211a
Capabilities: [d0] #10 [0001]
<CAT /PROC/INTERRUPTS>
CPU0
0: 154033 IO-APIC-edge timer
1: 8 IO-APIC-edge i8042
7: 0 IO-APIC-edge parport0
8: 4 IO-APIC-edge rtc
9: 19291 IO-APIC-level acpi
12: 97 IO-APIC-edge i8042
14: 792 IO-APIC-edge ide0
169: 2055 IO-APIC-level uhci_hcd:usb4, eth0
193: 0 IO-APIC-level uhci_hcd:usb3
201: 8268 IO-APIC-level libata, uhci_hcd:usb2
209: 0 IO-APIC-level uhci_hcd:usb1, ehci_hcd:usb5
NMI: 0
LOC: 153986
ERR: 0
MIS: 0
<ACPIDUMP>
DSDT @ 0x1f7f3180
0000: 44 53 44 54 da 47 00 00 01 a8 49 4e 54 45 4c 52 DSDT.G....INTELR
0010: 41 57 52 44 41 43 50 49 00 10 00 00 4d 53 46 54 AWRDACPI....MSFT
0020: 0e 00 00 01 10 43 05 5c 5f 50 52 5f 5b 83 11 5c .....C.\_PR_[..\
0030: 2e 5f 50 52 5f 43 50 55 30 00 00 00 00 00 00 5b ._PR_CPU0......[
0040: 83 11 5c 2e 5f 50 52 5f 43 50 55 31 01 00 00 00 ..\._PR_CPU1....
0050: 00 00 5b 83 11 5c 2e 5f 50 52 5f 43 50 55 32 02 ..[..\._PR_CPU2.
0060: 00 00 00 00 00 5b 83 11 5c 2e 5f 50 52 5f 43 50 .....[..\._PR_CP
0070: 55 33 03 00 00 00 00 00 08 5c 5f 53 30 5f 12 0a U3.......\_S0_..
0080: 04 0a 00 0a 00 0a 00 0a 00 08 5c 5f 53 31 5f 12 ..........\_S1_.
0090: 0a 04 0a 01 0a 00 0a 00 0a 00 08 5c 53 53 33 5f ...........\SS3_
00a0: 12 0a 04 0a 05 0a 00 0a 00 0a 00 08 5c 5f 53 34 ............\_S4
00b0: 5f 12 0a 04 0a 06 0a 00 0a 00 0a 00 08 5c 5f 53 _............\_S
00c0: 35 5f 12 0a 04 0a 07 0a 00 0a 00 0a 00 08 46 4c 5_............FL
00d0: 41 47 0a 00 08 53 54 41 54 0a 00 5b 80 5c 44 45 AG...STAT..[.\DE
00e0: 42 47 01 0a 80 0a 01 5b 81 0c 5c 44 45 42 47 01 BG.....[..\DEBG.
00f0: 44 42 47 31 08 5b 80 45 58 54 4d 00 0c 30 f8 0f DBG1.[.EXTM..0..
0100: 00 0a 10 5b 81 29 45 58 54 4d 02 52 4f 4d 31 10 ...[.)EXTM.ROM1.
0110: 52 4d 53 31 10 52 4f 4d 32 10 52 4d 53 32 10 52 RMS1.ROM2.RMS2.R
0120: 4f 4d 33 10 52 4d 53 33 10 41 4d 45 4d 20 5b 80 OM3.RMS3.AMEM [.
0130: 5c 53 4d 49 43 01 0a b2 0a 01 5b 81 0c 5c 53 4d \SMIC.....[..\SM
0140: 49 43 01 53 43 50 5f 08 5b 80 5c 50 4d 31 53 01 IC.SCP_.[.\PM1S.
0150: 0b 00 04 0a 04 5b 81 1b 5c 50 4d 31 53 01 50 4d .....[..\PM1S.PM
0160: 30 30 08 50 4d 30 31 08 50 4d 30 32 08 50 4d 30 00.PM01.PM02.PM0
0170: 33 08 5b 80 5c 50 4d 32 53 01 0b 29 04 0a 01 5b 3.[.\PM2S..)...[
0180: 81 0e 5c 50 4d 32 53 01 00 01 50 4d 32 39 01 5b ..\PM2S...PM29.[
<I had to cut this out to keep the bug report under 65KB>
4790: 4c 43 59 a1 07 70 00 50 4c 43 59 86 5c 2e 5f 54 LCY..p.PLCY.\._T
47a0: 5a 5f 54 48 52 4d 0a 81 14 31 53 54 4d 50 02 70 Z_THRM...1STMP.p
47b0: 69 44 57 30 30 a0 12 68 53 54 48 59 44 42 30 30 iDW00..hSTHYDB00
47c0: 44 42 30 31 44 57 30 30 a1 11 53 54 4f 53 44 42 DB01DW00..STOSDB
47d0: 30 30 44 42 30 31 44 57 30 30 00DB01DW00
FACS @ 0x1f7f0000
0000: 46 41 43 53 40 00 00 00 00 00 00 00 00 00 00 00 [EMAIL PROTECTED]
0010: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
0020: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
0030: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
FACP @ 0x1f7f30c0
0000: 46 41 43 50 74 00 00 00 01 5c 49 6e 74 65 6c 52 FACPt....\IntelR
0010: 41 57 52 44 41 43 50 49 31 2e 30 42 41 57 52 44 AWRDACPI1.0BAWRD
0020: 00 00 00 00 00 00 7f 1f 80 31 7f 1f 01 00 09 00 .........1......
0030: b2 00 00 00 a1 a0 00 34 00 04 00 00 00 00 00 00 .......4........
0040: 04 04 00 00 00 00 00 00 00 00 00 00 08 04 00 00 ................
0050: 28 04 00 00 00 00 00 00 04 02 00 04 08 00 00 00 (...............
0060: 65 00 e9 03 00 00 00 00 01 01 0d 00 00 00 00 00 e...............
0070: a5 04 00 00 ....
BOOT @ 0x1f7f79c0
0000: 42 4f 4f 54 28 00 00 00 01 8c 49 6e 74 65 6c 52 BOOT(.....IntelR
0010: 41 57 52 44 41 43 50 49 31 2e 30 42 41 57 52 44 AWRDACPI1.0BAWRD
0020: 00 00 00 00 7f 00 00 00 ........
MCFG @ 0x1f7f7b40
0000: 4d 43 46 47 3c 00 00 00 01 2f 49 6e 74 65 6c 52 MCFG<..../IntelR
0010: 41 57 52 44 41 43 50 49 31 2e 30 42 41 57 52 44 AWRDACPI1.0BAWRD
0020: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0 ................
0030: 00 00 00 00 00 00 00 ff 00 00 00 00 ............
APIC @ 0x1f7f7a40
0000: 41 50 49 43 84 00 00 00 01 6c 49 6e 74 65 6c 52 APIC.....lIntelR
0010: 41 57 52 44 41 43 50 49 31 2e 30 42 41 57 52 44 AWRDACPI1.0BAWRD
0020: 00 00 00 00 00 00 e0 fe 01 00 00 00 00 08 00 00 ................
0030: 01 00 00 00 00 08 01 01 00 00 00 00 00 08 02 02 ................
0040: 00 00 00 00 00 08 03 03 00 00 00 00 01 0c 04 00 ................
0050: 00 00 c0 fe 00 00 00 00 02 0a 00 00 02 00 00 00 ................
0060: 00 00 02 0a 00 09 09 00 00 00 0d 00 04 06 00 05 ................
0070: 00 01 04 06 01 05 00 01 04 06 02 05 00 01 04 06 ................
0080: 03 05 00 01 ....
RSDT @ 0x1f7f3040
0000: 52 53 44 54 34 00 00 00 01 e0 49 6e 74 65 6c 52 RSDT4.....IntelR
0010: 41 57 52 44 41 43 50 49 31 2e 30 42 41 57 52 44 AWRDACPI1.0BAWRD
0020: 00 00 00 00 c0 30 7f 1f c0 79 7f 1f 40 7b 7f 1f [EMAIL PROTECTED]
0030: 40 7a 7f 1f @z..
RSD PTR @ 0xf9570
0000: 52 53 44 20 50 54 52 20 85 49 6e 74 65 6c 52 00 RSD PTR .IntelR.
0010: 40 30 7f 1f @0..
------- You are receiving this mail because: -------
You are the assignee for the bug, or are watching the assignee.
-------------------------------------------------------
Using Tomcat but need to do more? Need to support web services, security?
Get stuff done quickly with pre-integrated technology to make your job easier
Download IBM WebSphere Application Server v.1.0.1 based on Apache Geronimo
http://sel.as-us.falkag.net/sel?cmd=lnk&kid=120709&bid=263057&dat=121642
_______________________________________________
acpi-bugzilla mailing list
[email protected]
https://lists.sourceforge.net/lists/listinfo/acpi-bugzilla
