Here's the info from Qualstar.. Serialization was introduced in firmware 2.12h. It can be disabled by setting the Configuration\Advanced\Library\?\DtSerial menu item to NONE.
--- Kelly Lipp <[EMAIL PROTECTED]> wrote: > It is the DT Serial option. You need to find it in > the configuration menus > (I think it's in config, library) and turn it off. > Then it will work. This > is a new problem. The Qualstar microcode was > updated to use this SCSI > option differently which exposed a bug in TSM (I > believe it's a bug). If > you turn off DT Serial the library will define just > fine. > > Kelly J. Lipp > Storage Solutions Specialists, Inc. > PO Box 51313 > Colorado Springs, CO 80949 > [EMAIL PROTECTED] or [EMAIL PROTECTED] > www.storsol.com or www.storserver.com > (719)531-5926 > Fax: (240)539-7175 > > > -----Original Message----- > From: ADSM: Dist Stor Manager > [mailto:[EMAIL PROTECTED]]On Behalf Of > Doug Thorneycroft > Sent: Wednesday, October 17, 2001 2:44 PM > To: [EMAIL PROTECTED] > Subject: Re: Unable to define Qualstar TLS 4480 > library > > > Thank you, I sent the problem to tivoli support, and > supposidy, the serial numbers are not enabled on > this model. (This from the reseller, not qualstar) > I'll try calling qualstar tomorrow. > > On Wednesday, October 17, 2001 2:09 PM, Hunny > Kershaw > [SMTP:[EMAIL PROTECTED]] wrote: > > I am not familiar with the options on this > library. If > > you can't find other options to disable the serial > > numbers, you may want to contact the vendor and > find > > out how to disable the serial numbers if it's > possible > > at all. > > > > In the mean time, you may want to also contact the > TSM > > support team. If the problem is confirmed to be > caused > > by the serial numbers, the driver can be updated > to > > handle the serial numbers returned from this > library. > > > > Regards, > > > > HK.. > > > > --- Doug Thorneycroft <[EMAIL PROTECTED]> > wrote: > > > Ran the test, and I do get the 321 > (RES_MISMATCH) > > > return code. > > > I looked up DT Serial in the library manual but > it > > > says that it is not > > > applicable > > > to any drives used in the 4XXX series. > > > Some other option maby? > > > > > > On Wednesday, October 17, 2001 10:35 AM, Hunny > > > Kershaw > > > [SMTP:[EMAIL PROTECTED]] wrote: > > > > Please run lbtest to see if there's a problem > with > > > the > > > > Read Element Status command. > > > > > > > > lbtest -d lb0.0.0.7 > > > > 1. Manual Test > > > > 6. Open > > > > 8. Return Element Count > > > > > > > > If 8 fails with completion code 321 > > > (RES_MISMATCH), > > > > then there's a problem with the RES command. > > > Possibly, > > > > the firmware now returns drive serial numbers > > > which > > > > currently are not handled by the device > driver. > > > > > > > > Last week, one gentleman mentioned the work > around > > > on > > > > the TLS-8xxxx series. Try to find DT-SERIAL > option > > > on > > > > your library and disable that option. The > library > > > then > > > > will not return the serial numbers and things > > > should > > > > get moving again. > > > > > > > > Regards, > > > > > > > > > > __________________________________________________ > > Do You Yahoo!? > > Make a great connection at Yahoo! Personals. > > http://personals.yahoo.com __________________________________________________ Do You Yahoo!? Make a great connection at Yahoo! Personals. http://personals.yahoo.com
