My issue with them, real or imagined was that they would let water into the ends. I didn't want to gamble, as we have enough issues with water getting into things.
Honestly, once I got the process down, good quality ice cubes
were a snap.
bp
<part15sbs{at}gmail{dot}com>
I always imagined that the bloody ends of the wires would corrode.
Sent from my iPhone
On Feb 1, 2021, at 7:49 PM, Mathew Howard <[email protected]> wrote:
--I tried switching to the EZ connectors a few times... I honestly don't like them. It always seemed to me like they caused more problems than they solved.
On Mon, Feb 1, 2021, 8:09 PM Jason McKemie <[email protected]> wrote:
I stopped using them years ago since I always had issues getting the connectors to properly snap into Canopy SMs, plus after you terminate enough of them it really isn't any easier. I'm still using the crimpers about 15 years later though.
On Monday, February 1, 2021, SmarterBroadband <[email protected]> wrote:
--We have been using EZ Crimps for 10 plus years now, would not think of using anything else.
Adam
From: AF [mailto:[email protected]] On Behalf Of Forrest Christian (List Account)
Sent: Monday, February 1, 2021 2:59 PM
To: AnimalFarm Microwave Users Group <[email protected]>
Subject: Re: [AFMUG] OT: Expensive Cambium parts
I agree with the ratchet part - I think it's because the ratchet helps tell when you've crimped enough and not too much. They also seem to have a bit better leverage for some reason, although I have a feeling that that's not really true since I don't see how this would be the case.
I have done my fair share of terminations without a ratcheting tool. I will agree that good quality ends are more important. I also remember that finally realizing (years ago) that I could actually look at the wires in the connector before crimping to determine whether they were all the way in solved almost all of my problems..
Nowadays, I have far more problems with trimming the wires too long or too short. If I was an installer and did this every day I'd probably not have that problem. I've been tempted to move to the EZ rj45's which you push the wire all the way through and then the crimp tool cuts the ends off, but for as few as I personally do a year anymore I haven't been able to justify switching.
On Mon, Feb 1, 2021 at 2:51 PM Nate Burke <[email protected]> wrote:
One of my installers says that if they don't ratchet, they're no good. I've been using the cheap Monoprice crimpers without a problem. I think good quality ends are more important. It's been a couple years since I've bought ends though. (I bought a bunch)
On 2/1/2021 3:38 PM, Carl Peterson wrote:
What crimpers are connectors are en vogue these days. As tech-proof as possible. We seem to go through phases where we end up with a lot of ethernet cable related performance issues / service calls.
On Mon, Feb 1, 2021 at 3:35 PM Bill Prince <[email protected]> wrote:
I would want more than that for that kind of price.
I would want to be able to leave the connectors and cable in the room; walk out, and walk back in a few minutes later with the ends all crimped with heat shrink, and Velcro ties holding the new cables in a nice, neat loop.
bp<part15sbs{at}gmail{dot}com>On 2/1/2021 11:45 AM, Nate Burke wrote:
Just came across these. For that price I better be able to just shove a bare Cat5 in one side, and have a heat shrinked end come out the other. Or is there something else super special about these crimpers.
--
AF mailing list
[email protected]
http://af.afmug.com/mailman/listinfo/af_af.afmug.com
--
--
AF mailing list
[email protected]
http://af.afmug.com/mailman/listinfo/af_af.afmug.com
--
- Forrest
AF mailing list
[email protected]
http://af.afmug.com/mailman/listinfo/af_af.afmug.com
AF mailing list
[email protected]
http://af.afmug.com/mailman/listinfo/af_af.afmug.com
-- AF mailing list [email protected] http://af.afmug.com/mailman/listinfo/af_af.afmug.com
