I've played with the Grandstream system on the bench. If you already
have a grandstream pbx, it hooks up to your UCM.
At our church we have a Rosslare system. http://axtraxng.com/ It was
physically installed by a local locksmith, just because I didn't want to
deal with it, but we've done 100% of everything since it was installed.
Software runs on a PC Locally, and is freely downloadable from their
website. It's just a single controller board that all the readers and
locks run into. Using standard weigand protocol. I buy preprogrammed
HID cards on Ebay and the secretary can just load them in via the
software as she distributes them.
On 6/16/2022 2:53 PM, Sterling Jacobson wrote:
Sorry, autocorrected, it’s the Wiegand keypad output standard.
*From:* AF <[email protected]> *On Behalf Of * Sterling Jacobson
*Sent:* Thursday, June 16, 2022 1:47 PM
*To:* AnimalFarm Microwave Users Group <[email protected]>
*Subject:* Re: [AFMUG] Door Access Control System (self-install,
self-hosted)
You can get the parts off ebay or amazon pretty easy.
I’ve run a small box that appears to be the same self-hosted web based
system as several others/brands.
And then purchased standard Weiland based door lock/strike systems and
keypads and wired it to the box.
Works well, just had to figure out some of the wiring. The box picks
up a dhcp IP address and then you just browse to it to add/remove
cards and access codes etc.
Something almost exactly like this (when I searched door controller
access system on ebay):
https://www.ebay.com/itm/255585747876?hash=item3b821903a4:g:3kAAAOSwMIhiq3TW
*From:* AF <[email protected] <mailto:[email protected]>>
*On Behalf Of *Daniel Pautz via AF
*Sent:* Thursday, June 16, 2022 12:06 PM
*To:* 'AnimalFarm Microwave Users Group' <[email protected]
<mailto:[email protected]>>
*Cc:* Daniel Pautz <[email protected] <mailto:[email protected]>>
*Subject:* Re: [AFMUG] Door Access Control System (self-install,
self-hosted)
We use credoid here, pretty cheap. Picked up HID stuff on ebay super
cheap to make a system here (about a dozen doors, some with both nfc
and pin and some just nfc / hid).
*From:* AF <[email protected] <mailto:[email protected]>>
*On Behalf Of *Forrest Christian (List Account)
*Sent:* Thursday, June 16, 2022 12:01 PM
*To:* AnimalFarm Microwave Users Group <[email protected]
<mailto:[email protected]>>
*Subject:* [AFMUG] Door Access Control System (self-install, self-hosted)
Before I get pissed and just make something (which is how many of my
products start).
Is there a good door access system which meets the following requirements:
1) I can actually buy as a mere mortal and not a "security system
installer"
2) Is self-hosted and doesn't require an internet connection to operate
3) Supports both keypad and NFC card and/or phone access
Mainly I'm looking for a good old-fashioned door access system where I
can put a door controller in and put a latch lock on the door and have
staff come and go either with some sort of NFC access or have a keypad
to enter (if someone forgets their NFC or for third-party access to
the facility where needed).
It seems like either I have to be an installer, or it has to be an
internet-connected thing, or has a monthly fee.
I am aware of the unifi stuff from UBNT, not sure how I feel about
that, but if I don't find another option, I'll give that a try. If
someone has that in place, let me know as I'm curious how well it works.
--
- Forrest
--
AF mailing list
[email protected]
http://af.afmug.com/mailman/listinfo/af_af.afmug.com
