put a meter on any duplex outlet you buy On Sun, Sep 28, 2014 at 11:06 AM, Ken Hohhof via Af <[email protected]> wrote:
> Shouldn’t be. > > *From:* That One Guy via Af <[email protected]> > *Sent:* Sunday, September 28, 2014 10:50 AM > *To:* [email protected] > *Subject:* Re: [AFMUG] Gear in Tower - Grounded or Isolated? > > neutral is tied to mechanical ground anywhere there is an outlet anyway. > the ground lug on an outlet has continuity to neutral, I dont know why > > On Sun, Sep 28, 2014 at 9:42 AM, Ken Hohhof via Af <[email protected]> wrote: > >> Ground and neutral are not the same. Yes, they are tied together >> somewhere, probably the transformer. But you should not use the neutral as >> a ground or tie it to your ground anywhere. >> >> >> *From:* Kurt Fankhauser via Af <[email protected]> >> *Sent:* Sunday, September 28, 2014 7:38 AM >> *To:* [email protected] >> *Subject:* Re: [AFMUG] Gear in Tower - Grounded or Isolated? >> >> I have a grounding question for the cabinet at the base of the tower. >> My electrician wired in the incoming power to the cabinet but he did not >> bond the cabinet ground/neutral to the actual tower itself. Tower has its >> own separate ground rods and cabinet ground actually is back where the >> meter base is, (over 150 feet away) Should I bond the tower and the cabinet >> together? I already have electrical conduit running out of the cabinet and >> then attaches to the tower itself so there is metal to metal contact just >> wondering if I should have something better.... >> >> >> Kurt Fankhauser >> >> Wavelinc Communications >> >> P.O. Box 126 >> >> Bucyrus, OH 44820 >> >> http://www.wavelinc.com >> >> tel. 419-562-6405 >> >> fax. 419-617-0110 >> >> On Sun, Sep 28, 2014 at 8:19 AM, Gino Villarini via Af <[email protected]> >> wrote: >> >>> I do think too that isolating its easier and should be the way to go… >>> DC plant, fiber up. Problem would be mounts and tower attachments… >>> thinking of using PVC conduit? >>> >>> >>> >>> Gino A. Villarini >>> President >>> Aeronet Wireless Broadband Corp. >>> www.aeronetpr.com >>> @aeronetpr >>> >>> >>> >>> From: "[email protected]" <[email protected]> >>> Reply-To: "[email protected]" <[email protected]> >>> Date: Sunday, September 28, 2014 at 7:48 AM >>> To: "[email protected]" <[email protected]> >>> Subject: Re: [AFMUG] Gear in Tower - Grounded or Isolated? >>> >>> >>> Great question Gino. I hope we get some good input. >>> >>> My opinion is that you have to be completed isolated or extremely >>> properly grounded. Both can be complicated, but the second way being the >>> most complicated >>> >>> >>> >>> Paul >>> >>> >>> >>> *From:* Af [mailto:[email protected] >>> <[email protected]>] *On Behalf Of *Gino Villarini >>> via Af >>> *Sent:* Sunday, September 28, 2014 7:31 AM >>> *To:* [email protected] >>> *Subject:* [AFMUG] Gear in Tower - Grounded or Isolated? >>> >>> >>> >>> I remember the good old days that most of our network was based on >>> Canopy Classic: >>> >>> >>> >>> The radios were isolated form the tower, minor lightning issues.. >>> >>> >>> >>> Nowadays its has turned into a big issue for us, radios and MW getting >>> zapped! Were do I start? >>> >>> >>> >>> Should I go back to the Isolation model and have all gear in tower >>> isolated from the tower in any way possible? >>> >>> >>> >>> >>> >>> >>> >>> Gino A. Villarini >>> >>> President >>> >>> Aeronet Wireless Broadband Corp. >>> >>> www.aeronetpr.com >>> >>> @aeronetpr >>> >>> >>> >>> >>> >> >> > > > > -- > All parts should go together without forcing. You must remember that the > parts you are reassembling were disassembled by you. Therefore, if you > can't get them together again, there must be a reason. By all means, do not > use a hammer. -- IBM maintenance manual, 1925 > -- All parts should go together without forcing. You must remember that the parts you are reassembling were disassembled by you. Therefore, if you can't get them together again, there must be a reason. By all means, do not use a hammer. -- IBM maintenance manual, 1925
