how bad is the overall throughput hit in MIMO-A, did you notice if it cause the other SMs to modulate down?
On Fri, Oct 3, 2014 at 11:34 PM, George Skorup (Cyber Broadcasting) via Af < [email protected]> wrote: > Yes, I have a sector loaded that needed MIMO-A. And I found some minor > GUI issues and the Moto binary data GPS bug that has now been fixed in > build 32. But obviously I don't have things configured like others, such as > PPPoE, NAT, VLANs, etc. I just do bridge, no auth/RADIUS, very few APs > doing VLAN. So I would encourage more folks to test it out and give > feedback to Cambium so they can get any remaining issues ironed out and get > 13.2 official out. From the improvements I've seen so far, I want it on > every 450 AP and SM, right meow! > > > On 10/3/2014 9:55 PM, Bill Prince via Af wrote: > > On 13.2 already George?ן¿½ I am happy to let you others get the bleeding > done before I step over the edge. > > I think I will wait about a week before I give it a rip; and then only > only low-population APs. > > > bp > > On 10/3/2014 6:28 PM, George Skorup (Cyber Broadcasting) via Af wrote: > > I was just discussing with Aaron offlist about build 32 AutoSync selecting > the on-board GPS instead of timing port at boot. The deployed AP I have > been testing on has a Parasitic SyncPipe, no power port sync and the iGPS > on this AP usually always has a good lock. Prior to build 32, it would > always boot up and use the timing port. Now build 32 wants the on-board at > boot, at least every time I've had a chance to reboot the AP, which has > only been the update from build 30 to 32 and one reboot afterwards so far. > > I would like to know if anyone else sees the same thing happening with > build 32. Maybe it's just me, but I would prefer it to come up on the > timing port before the on-board GPS for tracking GPS status of the attached > SyncPipe. > > BTW, I've seen a very nice improvement in 13.2 beta for both throughput > and session issues during multipath events. I think 13.2 is going to be a > major leap forward for the 450. > > On 10/3/2014 6:19 PM, Aaron Schneider via Af wrote: > > Since the last Open Beta load (Build 30), this also contains: > > ן¿½ > > - Fix for negative VC count on home page > - New OID to see NAT table size in use > - Fix for Active FTP with NAT > - PPPoE Control Message High Priority with VLAN Enabled > > ן¿½ן¿½ן¿½ן¿½ן¿½ן¿½ן¿½ן¿½ Added missing OIDs for IPv6 packet filtering > configuration > > ן¿½ > > We are very close to release, so please give this load a try! > > ן¿½ > > Regards, > > ן¿½ > > -Aaron > > ן¿½ > > *From:* Af [mailto:[email protected] <[email protected]>] *On > Behalf Of *John Mehling via Af > *Sent:* Friday, October 03, 2014 6:10 PM > *To:* [email protected] > *Subject:* [AFMUG] 13.2 (Build32) Beta Software is Now Available!ן¿½ן¿½ > > ן¿½ > > Folks, > > Software version 13.2(Build32) has been added to the Cambium Open Beta > program for PMP450, PMP430, and PTP230. > > Please go here:ן¿½https://support.cambiumnetworks.com/betaן¿½if you would > like to test the new load and offer feedback on the Beta Forum. > > ן¿½Fixes in this release include: > > ן¿½ן¿½ן¿½ן¿½ן¿½ן¿½ן¿½ן¿½ן¿½ן¿½ן¿½ן¿½ן¿½ Fix for Motorola Binary GPS based > devices (CMM2, SyncPipe, etc) > > ן¿½ן¿½ן¿½ן¿½ן¿½ן¿½ן¿½ן¿½ן¿½ן¿½ן¿½ן¿½ן¿½ Fix for PTP450 link test with > small packets causing session drop and/or invalid readings > > ן¿½ > > This version also adds OID support for IPv6 packet filtering. > > As always, we look forward to your feedback.ן¿½ Thank you! > > -John > > ן¿½ > > ן¿½ > > *John Mehling* > > Senior Engineer - Support > > > *Cambium Networks* > 3800 Golf Rd.,ן¿½ Suite 360 > > Rolling Meadows, IL 60008 > > www.cambiumnetworks.com > > > [image: v_large_blue_noBG.png] > > ן¿½ > > > > > -- All parts should go together without forcing. You must remember that the parts you are reassembling were disassembled by you. Therefore, if you can't get them together again, there must be a reason. By all means, do not use a hammer. -- IBM maintenance manual, 1925
