are the serials set to the unit as in if I change them, then powercycle they will reset? It would sure be nice if the base unit could allow multiple IPs so you can assign the communication to each component seperately for SNMP purposes
On Fri, Oct 17, 2014 at 12:27 PM, George Skorup (Cyber Broadcasting) via Af <[email protected]> wrote: > Nope, it's almost always random. You can set the serials in the order > you want, then just issue a rescan.. move on with life. > > On 10/17/2014 12:25 PM, That One Guy via Af wrote: > > ok, so now a new question > I removed the devices > set to 0, cleared them > Then when I reconnected base unit-syncinjector-UPS > its showing the index order as base unit-UPS-syncinjector > > Does it not go in the physical order they are connected? > > On Fri, Oct 17, 2014 at 12:21 PM, That One Guy via Af <[email protected]> > wrote: > >> Jesus H Kittens >> My power supply was not connected, I didnt even think to look at that >> since the light was on, apparently that light is powered through the serial >> cable. Im a dumbass >> >> On Fri, Oct 17, 2014 at 12:17 PM, George Skorup (Cyber Broadcasting) via >> Af <[email protected]> wrote: >> >>> 6 flashes and the SyncPipe wouldn't power up means you didn't have the >>> power input to the SyncInjector connected, or no power to it. >>> >>> The SyncInjector will either power its expansion bus by itself (if it >>> has power on the input block) or it will take power from the base unit. >>> That's why you could see it connected to the base, but it obviously needs >>> its own power connected to power up radios and the SyncPipe. >>> >>> As everyone else has already said, to remove an expansion unit, just go >>> into the expansion tab and set the device's serial to zero. Power down the >>> base and physically remove the expansion unit from the bus. You should not >>> be hot-plugging anything on the expansion bus. Forrest said it probably >>> won't hurt anything, but just don't do it. >>> >>> On 10/17/2014 11:19 AM, That One Guy via Af wrote: >>> >>> I remember somebody asking this once before >>> How do you clear a device from a base unit. We were testing a >>> syncinjector then removed it and started testing a UPS moniter, but the >>> base unit still shows the syninjector, we have powercycled, we have >>> rescanned, still there. >>> >>> Also we have a syncpipe that when connected to the syncinjector does >>> not light up, the syncinjector ports green light just keeps flashing 6 times >>> >>> Is there a better set of instructions somewhere for using this gear, >>> the stuff on the packetflux website isnt complete or clear, maybe im just >>> not looking in the right spot? >>> >>> -- >>> All parts should go together without forcing. You must remember that the >>> parts you are reassembling were disassembled by you. Therefore, if you >>> can't get them together again, there must be a reason. By all means, do not >>> use a hammer. -- IBM maintenance manual, 1925 >>> >>> >>> >> >> >> -- >> All parts should go together without forcing. You must remember that the >> parts you are reassembling were disassembled by you. Therefore, if you >> can't get them together again, there must be a reason. By all means, do not >> use a hammer. -- IBM maintenance manual, 1925 >> > > > > -- > All parts should go together without forcing. You must remember that the > parts you are reassembling were disassembled by you. Therefore, if you > can't get them together again, there must be a reason. By all means, do not > use a hammer. -- IBM maintenance manual, 1925 > > > -- All parts should go together without forcing. You must remember that the parts you are reassembling were disassembled by you. Therefore, if you can't get them together again, there must be a reason. By all means, do not use a hammer. -- IBM maintenance manual, 1925
