Think it was build 25 on the AP yeah it needs updated just wanted to be sure all the other installers out there knew I almost did not do the install
— Sent from Mailbox On Fri, Nov 14, 2014 at 5:52 PM, Aaron Schneider via Af <[email protected]> wrote: > What beta version is on the AP? There was an issue with early beta release > and RF speedtest that was addressed in later (should have been 28 and onward) > beta loads. > Please get your sector all up onto 13.2 official if you are on the beta, then > retry the scenario and if it still happens, please send me a CNUT capture of > the SM. > Regards, > -Aaron > From: Af [mailto:[email protected]] On Behalf Of timothy steele via Af > Sent: Friday, November 14, 2014 4:36 PM > To: [email protected] > Cc: [email protected] > Subject: Re: [AFMUG] System Release 13.2 is Official > I think someone else already said this but 13.2 final on SM with beta on AP > the SM will reboot it self when you do a cap test this is the same bug I > reported on build 35 > — > Sent from Mailbox<https://www.dropbox.com/mailbox> > On Fri, Nov 14, 2014 at 4:46 PM, Aaron Schneider via Af > <[email protected]<mailto:[email protected]>> wrote: > There was a decision made when we added 2.5 center channels that on upgrade > we wouldn’t automatically check the 2.5 centers unless the scan list was in a > default (all checked) state. We didn’t want to add a ton of new scan options > on an upgrade which increased the scanning time. When setting a unit that > is on a load that supports 2.5M centers to default, then all (including 2.5 > centers) should be selected. > We are still investigating, but likely this has something to do with what > Ryan was seeing when others weren’t seeing the same behavior. > -Aaron > From: Af [mailto:[email protected]] On Behalf Of George Skorup (Cyber > Broadcasting) via Af > Sent: Friday, November 14, 2014 12:58 PM > To: [email protected]<mailto:[email protected]> > Subject: Re: [AFMUG] System Release 13.2 is Official > I'm trying to remember.. did the 2.4 450 have 2.5 centers from day one? I > think the last time I got some new SMs in, they had either 12.0.x or 12.1.x > on them and none of the 2.5 centers were checked after updating to 13.x. So > maybe the safest approach from now on is to enable everything in the scan > list automatically during/after update? Then tell everyone in the release > notes about it. You'd be surprised at how many of us fully read the release > notes now. OK, at least I do. > On 11/14/2014 11:28 AM, Rajesh Vijayakumar via Af wrote: > Its good to get confirmation of multiple successful upgrades with 2.4 GHz. > We have not been able to recreate the problem yet. The test team is trying a > number of combinations of upgrade/downgrade. > --Rajesh Vijayakumar > Cambium Networks > On Fri, Nov 14, 2014 at 11:01 AM, Eric Muehleisen via Af > <[email protected]<mailto:[email protected]>> wrote: > Any changes/improvements in the Rate Adapt? > On Fri, Nov 14, 2014 at 10:54 AM, Bill Prince via Af > <[email protected]<mailto:[email protected]>> wrote: > As mentioned in another thread, we upgraded a bunch of PMP430 installations > last night. Something that I wasn't expecting was an immediate improvement > in the SNR (typical example below). This was pretty much across the board > excepting installations that already had really good SNR. > Thanks Cambium! > <image001.png> > bp > <part-15@SkylineBroadbandService> > On 11/13/2014 5:12 AM, Matt Mangriotis via Af wrote: > It is here! > We released 13.2 this morning officially. Come to our forum to discuss > anything about it. > http://community.cambiumnetworks.com/t5/PMP-450/System-Release-13-2-Now-Avaialable/m-p/36254/thread-id/278 > Download the software from the usual place on our support site: > https://support.cambiumnetworks.com/files/pmp450/ > Thanks to all of you that Beta tested this software with us, and helped to > make it stronger and better than ever. Now that this is here, we’re hard at > work on delivering the next round of enhancements (code name 13.3 (pretty > original, huh?)) which are right around the corner. > The momentum is building on the PMP 450 platform. > Thanks again, > Matt
