Nope, no authentication at all.
Next time it happens, I will try to get the logs. It's impossible to
know when or where it will strike, so retrieving the SM's side of the
logs is very unlikely while this is occurring. Maybe I can get my house
moved over to a 3.6 450 on Friday or some time next week and wait for it
to happen.
I have never seen this issue on 5GHz or the one lonely 2.4GHz 450 we
have up. Something with the 3.6GHz 450 is just... different. The only
thing that comes to mind is LBT which I understand is modified DFS.
Maybe the thing is that I don't have any alternate frequencies
configured on any of the 3.6 450 sectors. There's simply no alternate
channels to have a sector move to in a cluster. Many of these are
co-located with UBNT 3.65 running in the lower half of the band while
we're migrating customers to the 450.
On 9/9/2015 10:28 PM, Chitrang Srivastava wrote:
Hi George,
For your other issues where SM fails to register and you have to reboot AP.
Please send AP logs , on AP goto 'logs - SM sessions' and then select luid of
SM which has problem, after submitting you will get the logs,
Further if it is possible to reach SM please get similar logs 'logs - AP
session '
We are working on a similar issue but with RADIUS authentication for SM, for
you SM authentication is radius as well?
Thanks
Chitrang Srivastava
________________________________________
From: Af <[email protected]> on behalf of George Skorup <[email protected]>
Sent: 29 August 2015 09:30:14
To: [email protected]
Subject: Re: [AFMUG] Canopy 13.4 Watchdog Reset
What does FreeRun have to do with it?
I have a couple 450 test sites on 13.4 and haven't seen any watchdog
resets. Granted, that's only two APs. Definitely still see it on 13.2.1.
It's not a daily thing, but yeah, annoying.
One thing I'm seeing on the 3.6 450 with 13.2.1 is the APs getting into
a state where they say there's no sync pulse. Then it says receiving
sync, no sync... over and over every few seconds until they are
rebooted. All the while the SyncInjector says nothing is wrong. Tracking
8+ sats. No increment for the 1PPS Active counter. I understand this had
something to do with the FreeRun stuck issue, which was apparently
resolved with 13.4, but I'm waiting on 13.4.1 so some other issues get
fixed before I can update the entire network.
Anyway, if I leave the APs alone for a while (say it happens in the
middle of the night while I'm sleeping), they mysteriously return to
normal after anywhere from 3 to 20 minutes. Then if any SM loses
registration (or if I force an SM to rescan), it fails to register for
no reason at all. Reboot the AP, everything works again. I have no
freakin idea what this is about.
On 8/28/2015 9:54 PM, Mark Radabaugh wrote:
We have been seeing this across 200+ AP's
It's getting truly annoying. Cambium tech support has helpful suggestions
like'just put them in free run'. Um.... Thanks for the help, but no.
Mark Radabaugh
Amplex
27800 Lemoyne, Ste F
Millbury, OH 43447
419-261-5996
On Aug 28, 2015, at 4:56 PM, Brian Sullivan <[email protected]> wrote:
Last week we rolled out 13.4 to 450 AP's after testing in-house for a while.
While running 13.2 we would see an AP here or there reboot on occasion by
itself. The only message in the Event Log mentions Watchdog Reset. This is
one of the bugs that Cambium noted was fixed in the 13.4 release notes.
Since we upgraded the network to 13.4 we are now seeing at least 4 AP's out
there rebooting several times per day. On one of these AP's we are also seeing
SM's (all 17 registered) reboot along with the AP. The site has UPS backup so
I know it's not a power grid problem. I am planning to roll the affected AP's
back to 13.2 this evening.
Anyone else having Watchdog issues with the 13.4 release?
******System Startup******
System Reset Exception -- Watchdog Reset
Software Version : CANOPY 13.4 AP-DES
Board Type : P12
Device Setting : 5.7GHz MIMO OFDM - Access Point - 0a-00-3e-a0-08-e5 - 5760.0
MHz - 20.0 MHz - 1/16 - CC 85 - 2.5 ms
FPGA Version : 040715
FPGA Features : DES, Sched, US/ETSI;
08/28/2015 : 14:11:42 CST : :Time Set
08/28/2015 : 14:11:58 CST : Acquired sync pulse from Power Port.
