Bill- Bingo, so it’s a single CAT5 RJ45 8P8C from the SyncInjector’s “SyncPipe” port to the center RJ45 of the SyncPipe Deluxe and that’s the complete connection. Thanks, we tried this before coming here but apparently had something wrong as when I tried it again it worked. (:
Thanks again, Scott From: Af [mailto:[email protected]] On Behalf Of Bill Prince Sent: Tuesday, December 29, 2015 17:04 To: [email protected] Subject: Re: [AFMUG] SyncInjector n00b question When the syncpipe is plugged into the sync injector, it gets power and transfers data over through the ethernet cable (RJ45 at each end). bp <part15sbs{at}gmail{dot}com> On 12/29/2015 5:01 PM, Josh Luthman wrote: No POE. Both devices need power. The Syncpipe has a GPS module and does timing on the 6p6c ports. Timing ports can be daisy chained (which is how SyncInjector gets timing). Josh Luthman Office: 937-552-2340 Direct: 937-552-2343 1100 Wayne St Suite 1337 Troy, OH 45373 On Dec 29, 2015 7:53 PM, "Scott Vander Dussen" <[email protected]<mailto:[email protected]>> wrote: OK, so the SyncInjector provides PoE from its “SyncPipe or Daisy Chain In” RJ45 port, and that plugs into the center RJ45 port of the SyncPipe? So the SyncPipe receives PoE from the SyncInjector and sends timing back though that same cable? I tried that and it didn’t work :/ From: Af [mailto:[email protected]<mailto:[email protected]>] On Behalf Of Josh Luthman Sent: Tuesday, December 29, 2015 16:49 To: [email protected]<mailto:[email protected]> Subject: Re: [AFMUG] SyncInjector n00b question Correct. RJ45 simply won't fit on the outside ones. It will have one of the LEDs on when it's powered/booted if memory serves. Maybe green? I think the amber blinks every second or three to let you know it's good to go...something like that... Josh Luthman Office: 937-552-2340<tel:937-552-2340> Direct: 937-552-2343<tel:937-552-2343> 1100 Wayne St Suite 1337 Troy, OH 45373 On Tue, Dec 29, 2015 at 7:46 PM, Steve Utick <[email protected]<mailto:[email protected]>> wrote: And, I believe it needs to be plugged into the center jack on the SyncPipe as well, not the side ones. The side ones are 6p6c connectors to provide sync to a A/P by sync cable. On Tue, Dec 29, 2015 at 5:44 PM, Josh Luthman <[email protected]<mailto:[email protected]>> wrote: Syncpipe needs power. Up to 50v? Josh Luthman Office: 937-552-2340<tel:937-552-2340> Direct: 937-552-2343<tel:937-552-2343> 1100 Wayne St Suite 1337 Troy, OH 45373 On Dec 29, 2015 7:18 PM, "Scott Vander Dussen" <[email protected]<mailto:[email protected]>> wrote: Trying to use a SyncInjector to provide timing over power to a mix of 100/450APs. Gigabit SyncInjector revision I0, SyncPipe Deluxe revision H1 both receiving 27vdc. SyncPipe timing port directly to APs timing port works fine. SyncPipe timing port to SyncInjector “SyncPipe or Daisy Chain In” port does not seem to work. (see syncinjector.jpg) I’ve tried two SyncInjectors with the same results. If the SyncInjector is receiving sync from the SyncPipe, should I see the value column populated? (See site monitor string.png) Is there any configuration I need to change for the SyncInjector/SiteMonitor to make this combo work? Thanks in advance.
