Aren't the CTM2's like 2k/each? On Tue, Mar 1, 2016 at 2:07 PM, Sean Heskett <[email protected]> wrote:
> You just described the last mile gear CTM2 > > -Sean > > > On Tuesday, March 1, 2016, Peter Kranz <[email protected]> wrote: > >> Here is my ideal solution: >> >> >> >> - Solid state fusing on each radio, so that I get cable or >> radio damage it doesn’t take down my entire +24V power rail, it just shuts >> down that port >> >> - The ability to enable/disable the power rail remotely to each >> port for hard resets >> >> - A power rail that accepts two power supplies and will handle >> the failure of either device without dropping the APs >> >> - 19” rack mountable >> >> - If device requires fans or internal power supplies, they >> should be replaceable without having to take the unit out of service. >> >> >> >> Nice to have (but not a deal killer) >> >> >> >> - Multi-voltage capable... 48V UPOE for Siklus, 24V for UBNT >> and Cambium >> >> >> >> What I don’t want >> >> >> >> - A built in switch, I already have fancy ass switches, why do >> I need another switch in the way, probably with crappy features and poor >> buffers. >> >> >> >> >> *Peter Kranz*www.UnwiredLtd.com <http://www.unwiredltd.com/> >> Desk: 510-868-1614 x100 >> Mobile: 510-207-0000 >> [email protected] >> >> >> >> *From:* Af [mailto:[email protected]] *On Behalf Of *Chuck McCown >> *Sent:* Monday, February 29, 2016 3:27 PM >> *To:* [email protected] >> *Subject:* Re: [AFMUG] Mid-Span multi-voltage power injector >> withredundant power.. >> >> >> >> The power bus can be done. But price will jump quite a bit. I have >> worked up a design for this but always backed off due to the cost. One of >> the problems is that there is a connector I need that cannot be put on the >> circuit board by machine. Lots of hand work. So if I build it will anyone >> come? >> >> >> >> *From:* Peter Kranz >> >> *Sent:* Monday, February 29, 2016 3:55 PM >> >> *To:* [email protected] >> >> *Subject:* Re: [AFMUG] Mid-Span multi-voltage power injector >> withredundant power.. >> >> >> >> I like the idea, but no solid state fusing, no power buss, tons of >> wiring, it’s a mess to deploy this when you have over 20 APs on a single >> tower.. >> >> >> >> >> *Peter Kranz*www.UnwiredLtd.com <http://www.unwiredltd.com/> >> Desk: 510-868-1614 x100 >> Mobile: 510-207-0000 >> [email protected] >> >> >> >> *From:* Af [mailto:[email protected]] *On Behalf Of *Sean Heskett >> *Sent:* Monday, February 29, 2016 10:35 AM >> *To:* [email protected] >> *Subject:* Re: [AFMUG] Mid-Span multi-voltage power injector with >> redundant power.. >> >> >> >> >> >> >> >> GigE-POE- APC >> http://www.mccowntech.com/rack-mount-gige-poe-apc-surge-suppressor-power-inserter-protector/ >> >> >> >> You can load 24 of them in a 1U rack >> >> >> >> -Sean >> >> On Monday, February 29, 2016, Peter Kranz <[email protected]> wrote: >> >> Curious if anyone has recommendations on a mid-span power injector that >> supports multiple voltages and provides redundant power, ideally >> hot-swappable. I don’t really want a switch like the netonix boxes, I’d >> rather just have a mid-span device. >> >> >> >> >> *Peter Kranz*www.UnwiredLtd.com <http://www.unwiredltd.com/> >> Desk: 510-868-1614 x100 >> Mobile: 510-207-0000 >> javascript:_e(%7B%7D,'cvml','[email protected]'); >> >> >> >>
