Why do people act like STP is some evil proprietary Cisco thing? If you don't want it, turn if off, but don't make it sound like Cisco pulled it out of their ass, it's a perfectly standard Layer 2 protocol.
CDP you can yell at Cisco (although Mikrotik supports it). Certain VLAN error messages you can yell at Cisco. From: Af [mailto:[email protected]] On Behalf Of Carlos Alcantar Sent: Tuesday, October 25, 2016 4:58 PM To: [email protected] Subject: Re: [AFMUG] stp on the access side where you might have issues with stp is if your customer is then connecting to a cisco switch these stp messages between equipment can get funny and start shutting off ports because one side supports it and the other doesn't. you'll go crazy locating these issues. Carlos Alcantar Race Communications / Race Team Member 1325 Howard Ave. #604, Burlingame, CA. 94010 Phone: +1 415 376 3314 / <mailto:[email protected]> [email protected] / <http://www.race.com/> http://www.race.com _____ From: Af <[email protected] <mailto:[email protected]> > on behalf of Josh Reynolds <[email protected] <mailto:[email protected]> > Sent: Tuesday, October 25, 2016 2:38:04 PM To: [email protected] <mailto:[email protected]> Subject: Re: [AFMUG] stp You veered way off into something I wasn't even talking about. There's nothing wrong with a loop protect on an access port, but since its not an official standard, there will be variances in loop detection algorithm quality and design between vendors. YMMV. That said, there's nothing wrong with STP on access ports either. On Oct 25, 2016 4:27 PM, "George Skorup" <[email protected] <mailto:[email protected]> > wrote: Care to explain? What's wrong with simple loop-protect on an edge port facing a dumb customer? On 10/25/2016 3:07 PM, Josh Reynolds wrote: *facepalm* On Oct 25, 2016 3:06 PM, "George Skorup" <[email protected] <mailto:[email protected]> > wrote: Lots of switch vendors and even MikroTik (in the 6.37 branch, IIRC) support loop protection. If all you care about is stopping a loop, then use that. Use STP if you need its functionality. On 10/25/2016 1:16 PM, Josh Reynolds wrote: If one of the ports has a loop, it will block only that port. Obviously, disable STP on uplinks. On Oct 25, 2016 1:08 PM, "Chuck McCown" <[email protected] <mailto:[email protected]> > wrote: But if you only have one upstream connection and you fall, it isn't going to do anything, right? From: Josh Reynolds Sent: Tuesday, October 25, 2016 12:01 PM To: [email protected] <mailto:[email protected]> Subject: Re: [AFMUG] stp STP is a safety net. Its not doing much unless you fall. On Oct 25, 2016 12:44 PM, "Chuck McCown" <[email protected] <mailto:[email protected]> > wrote: How can STP being enabled help anything if you are not using it? From: Josh Luthman Sent: Tuesday, October 25, 2016 10:10 AM To: [email protected] <mailto:[email protected]> Subject: Re: [AFMUG] stp I just learned the other day thanks to Steve the Mikrotik software bridges are (R?) STP by default. Josh Luthman Office: 937-552-2340 <tel:937-552-2340> Direct: 937-552-2343 <tel:937-552-2343> 1100 Wayne St Suite 1337 Troy, OH 45373 On Tue, Oct 25, 2016 at 12:07 PM, Bill Prince <[email protected] <mailto:[email protected]> > wrote: Actually Netonix (one t, no r). I don't know that I would leave it on, but I don't know how you're using it. https://www.netonix.com/wisp-switch.html bp <part15sbs{at}gmail{dot}com> On 10/25/2016 9:04 AM, Josh Reynolds wrote: Nettonix. You could always leave it on... If your access network is layer2 up to that switch, it could help. On Oct 25, 2016 11:03 AM, "CBB - Jay Fuller" <[email protected] <mailto:[email protected]> > wrote: just discovered on one of our nettronix switches spanning tree protocol was enabled. we've run this switch probably four months - no real side effects - but i don't run stp anywhere else. any reason to leave this on? thanks
