Yup that's true.
------ Original Message ------
From: "Dennis Burgess" <[email protected]>
To: "[email protected]" <[email protected]>
Sent: 2/27/2017 4:59:18 PM
Subject: Re: [AFMUG] Mikrotik quick view for unknown subnets
Switch can do it too, port isolation! Lol note, not a dumb switch
though. Nettoix I belive does it.
Dennis Burgess – Network Solution Engineer – Consultant
MikroTik Certified Trainer/Consultant
<http://www.linktechs.net/productcart/pc/viewcontent.asp?idpage=5> –
MTCNA, MTCRE, MTCWE, MTCTCE, MTCINE
For Wireless Hardware/Routers visit www.linktechs.net
Radio Frequiency Coverages: www.towercoverage.com
Office: 314-735-0270
E-Mail: [email protected]
From: Af [mailto:[email protected]] On Behalf Of Adam Moffett
Sent: Monday, February 27, 2017 3:57 PM
To:[email protected]
Subject: Re: [AFMUG] Mikrotik quick view for unknown subnets
Only on two different router interfaces. If they're on a switch, then
no.
I think Dennis may be referring to how you should ideally have things
configured, and I think you're talking specifically about the feature
in Canopy equipment labeled "SM Isolation".
Ideally, yeah you should make it so one customer can't break everyone.
That's a multi-faceted thing and SM Isolation is one component of it.
If you're looking specifically for a router plugged in backwards, add a
DHCP-client to the interface facing the AP, and (*critical*) uncheck
the boxes for "add default route" and "add peer DNS". That might be
the kind of quick, simple test you're hoping for.
------ Original Message ------
From: "That One Guy /sarcasm" <[email protected]>
To: "[email protected]" <[email protected]>
Sent: 2/27/2017 4:42:02 PM
Subject: Re: [AFMUG] Mikrotik quick view for unknown subnets
clients on two different access points wil be blocked by client
isolation?
On Mon, Feb 27, 2017 at 3:35 PM, Dennis Burgess
<[email protected]> wrote:
There is no reason why it would and should not . J You can easily
allow the one offs …
Dennis Burgess – Network Solution Engineer – Consultant
MikroTik Certified Trainer/Consultant
<http://www.linktechs.net/productcart/pc/viewcontent.asp?idpage=5> –
MTCNA, MTCRE, MTCWE, MTCTCE, MTCINE
For Wireless Hardware/Routers visit www.linktechs.net
Radio Frequiency Coverages: www.towercoverage.com
Office: 314-735-0270 <tel:(314)%20735-0270>
E-Mail: [email protected]
From: Af [mailto:[email protected]] On Behalf Of That One Guy
/sarcasm
Sent: Monday, February 27, 2017 1:13 PM
To:[email protected]
Subject: Re: [AFMUG] Mikrotik quick view for unknown subnets
A. we have some locations where we dont use client isolation and B
client isolation doesnt apply to two access points as far as I know
On Mon, Feb 27, 2017 at 12:42 PM, Dennis Burgess
<[email protected]> wrote:
Your client isolation should take care of that. FYI.
Dennis Burgess – Network Solution Engineer – Consultant
MikroTik Certified Trainer/Consultant
<http://www.linktechs.net/productcart/pc/viewcontent.asp?idpage=5> –
MTCNA, MTCRE, MTCWE, MTCTCE, MTCINE
For Wireless Hardware/Routers visit www.linktechs.net
Radio Frequiency Coverages: www.towercoverage.com
Office: 314-735-0270 <tel:(314)%20735-0270>
E-Mail: [email protected]
From: Af [mailto:[email protected]] On Behalf Of That One Guy
/sarcasm
Sent: Monday, February 27, 2017 12:42 PM
To:[email protected]
Subject: Re: [AFMUG] Mikrotik quick view for unknown subnets
I wasnt clear, I was actually looking for rogue subnets in general
another issue example is that a customer with some time clocks
recently had a slick tech put a switch in before the router at
multiple locations from the same site, different APs, we bridge the
APs at the POP, so they were directly communicating
On Mon, Feb 27, 2017 at 12:33 PM, Faisal Imtiaz
<[email protected]> wrote:
You might find the useful.
https://forum.mikrotik.com/viewtopic.php?t=23640
Regards.
Faisal Imtiaz
Snappy Internet & Telecom
7266 SW 48 Street
Miami, FL 33155
Tel: 305 663 5518 x 232 <tel:(305)%20663-5518>
Help-desk: (305)663-5518 <tel:(305)%20663-5518> Option 2 or Email:
[email protected] <mailto:[email protected]>
--------------------------------------------------------------------------------
From: "That One Guy /sarcasm" <[email protected]>
To: [email protected]
Sent: Monday, February 27, 2017 11:34:59 AM
Subject: [AFMUG] Mikrotik quick view for unknown subnets
If, for example a customer has a router connected backward, is
there an arp(ish) check aside from packet sniffing to see this
since its not a subnet on the interface and there wont be an arp
entry?
--
If you only see yourself as part of the team but you don't see
your team as part of yourself you have already failed as part of
the team.
--
If you only see yourself as part of the team but you don't see your
team as part of yourself you have already failed as part of the
team.
--
If you only see yourself as part of the team but you don't see your
team as part of yourself you have already failed as part of the team.
--
If you only see yourself as part of the team but you don't see your
team as part of yourself you have already failed as part of the team.
