>> What is the difference in us and us licensed? Can i change it now?
I am not 100% sure, I did the same 'mistake' and was asked to redo..... Process is simple.. request the unlock code again... once you receive it.. reset the radio and enter the new code. Regards. Faisal Imtiaz Snappy Internet & Telecom 7266 SW 48 Street Miami, FL 33155 Tel: 305 663 5518 x 232 Help-desk: (305)663-5518 Option 2 or Email: [email protected] > From: "Steve Jones" <[email protected]> > To: [email protected] > Sent: Thursday, August 24, 2017 8:27:16 AM > Subject: Re: [AFMUG] mimosa b11 > Everything is knee jerk with me, i hated saf the first time because of the > save > config and write config. > Ive been using edge, i should have tested browsers, maybe ot wont be abusmal > in > others. > What is the difference in us and us licensed? Can i change it now? > On Aug 24, 2017 7:20 AM, "Faisal Imtiaz" < [email protected] > wrote: >> Each one of your 'rants' I would chalk them off to 'knee jerk' reaction on >> dealing with something new. >> One's experience with the GUI has more to do with the Browser one is using... >> Lately we have seen issues Chrome and Mimosa GUI, Mozilla tends to be more >> stable, typically I use Chrome as my primary, and Mozilla as my secondary go >> to. >> Reboot and re-connect times are nothing out of the ordinary, when compared to >> SAF / Ceragon / Ubiquity etc etc... >> Yes registration and initial firmware upload is what lot of people complain >> about...I shurg ! >> Also, keep in mind when you register it, do change the country code to USA >> Licensed instead of USA (when you are requesting the unlock code). >> Latest Firmware has been very good, so far our B11 has been pretty much 'set >> it >> and forget it' :) >> Doing bench testing, keep in mind to turn down the power..... and don't >> forget >> to turn up the power when you are installing it. >> Best of luck. >> Regards. >> Faisal Imtiaz >> Snappy Internet & Telecom >> 7266 SW 48 Street >> Miami, FL 33155 >> Tel: 305 663 5518 x 232 >> Help-desk: (305)663-5518 Option 2 or Email: [email protected] >>> From: "Steve Jones" < [email protected] > >>> To: [email protected] >>> Sent: Thursday, August 24, 2017 12:54:50 AM >>> Subject: Re: [AFMUG] mimosa b11 >>> ill have to look into browser >>> by clunky I mean slow to load, multiple instances where it went to the login >>> screen for no reason, a junk gui to me is indicative of the gears quality, >>> unless the gear is designed for cli and gui is an afterthought >>> at least its not java, ill give it that >>> I guess I'm just babied on saf, fast, never an issue with the interface. >>> On Wed, Aug 23, 2017 at 11:24 PM, Rory Conaway < [email protected] > >>> wrote: >>>> Steve, you are mistaken on a couple of things. I’m not sure how you say >>>> it’s >>>> clunky. It’s pretty easy, as are most of the vendors GUI’s. >>>> As for our statement about the road trip, that is completely false. If the >>>> AP is >>>> on the connection side, the client side will always search and connect. >>>> Every manufacturer ships with older firmware so again, I don’t see how >>>> that is >>>> any different than anyone else. >>>> As for the SSID, you have to use Chrome. If you use IE, then the save >>>> button >>>> doesn’t pop up. Chrome lets you type in whatever you want. >>>> Rory >>>> From: Af [mailto: [email protected] ] On Behalf Of Steve Jones >>>> Sent: Wednesday, August 23, 2017 8:55 PM >>>> To: [email protected] >>>> Subject: [AFMUG] mimosa b11 >>>> very unimpressed thus far and theyre just sitting on my living room floor >>>> web interface is so clunky, pretty well guarantees if a link has any issue >>>> no >>>> getting to the other side to reboot it, definite road trip, glad these are >>>> going in a redundant path >>>> essids reverting to factory... awesome >>>> I can guarantee we will need two spares because the first time I'm going >>>> to do a >>>> replacement after a storm in inclement weather and this stupid 30 minute >>>> process of activating, loading firmwares, all that, the first ones getting >>>> chucked through a window >>>> seriously, you have to scan essid? you cant just put it in, how freaking >>>> stupid >>>> is that. >>>> now I haven't checked the maps, but I'm pretty confident theres no 11ghz >>>> link >>>> going through my house, so a noise floor in the low 80s is pretty suspect. >>>> wondering if my 5ghz ap is the source of that "11ghz" fucking upconverts, I >>>> should have researched more >>>> the blazing fast speed of the interface is making me have some respect for >>>> the >>>> epmp >>>> reboot time on this "carrier class" product is outstanding, pretty sure if >>>> I >>>> ever have to reboot in production ill have time to drive to everybodys >>>> house >>>> and let them know whats going on before it comes back up. >>>> I do like that radiowaves has a mimisa interface for the hp line of >>>> antennas >>>> though, so if need be ill just pull it off and put a saf interface on.
