Thanks. I had seen that option but it's not exactly what I want. Don't want to force an exit from an already open position. But rather, prevent an opposite position from opening in the first place. Is there a way to easily implement such a condition?
--- In [email protected], Graham <[EMAIL PROTECTED]> wrote: > > SetOption( "ReverseSignalForcesExit", 0 ); > > -- > Cheers > Graham Kav > AFL Writing Service > http://www.aflwriting.com > > > > 2008/7/12 ozzyapeman <[EMAIL PROTECTED]>: > > Graham (or anyone), one more quick question if you don't mind. > > > > What is the easiest way to ensure that when I already have an open > > Long position, that I don't open a Short and vice versa? Should I > > place SetPositionSize inside the loop? > > > > Or is there some other way to specify in the original Buy and Short > > rules not to Buy or Short if it's opposite is already true? I can't > > test the inBuy or inShort variables because those only get defined > > lower down: > > > > > > SetTradeDelays( 1, 1, 1, 1 ); > > SetPositionSize(1,spsShares); > > > > Sell = Cover = 0; > > BuyPrice = SellPrice = ShortPrice = CoverPrice = O; > > > > myMA1 = MA(C,4); > > MyMA2 = MA(C,15); > > > > Buy = (myMA1 > MyMA2); > > Short = (myMA1 < MyMA2); > > > > inBuy = inShort = 0; > > ValueAtBuy = ValueAtShort = Null; > > > > > > for( i = 0; i < BarCount; i++ ) > > { //various trade rules here > > } > > > > > > > > > > --- In [email protected], Graham <kavemanperth@> wrote: > >> > >> Because AB AFL goes through each line if you define something later > >> then it will override previous results. > >> > >> When you use a loop it interupts this normal flow as well > >> > >> I find that if I am defining or changing trade signals with a loop it > >> is best to incorporate the other exits within the loop. ie define them > >> as conditions. This may be just because I have not found another way > >> to do it. > >> In this case add the actual price conditions to the loop and remove > >> the applystop > >> > >> Sorry I do not think I explained this very well, so hope you get my > > meaning. > >> > >> -- > >> Cheers > >> Graham Kav > >> AFL Writing Service > >> http://www.aflwriting.com > >> > >> > >> > >> 2008/7/12 ozzyapeman <zoopfree@>: > >> > Hello, would appreciate if anyone could help me with fixing this stop > >> > problem. > >> > > >> > I want to apply a stop on either a Buy or Short, should the price move > >> > against me by 20 pips on a Forex trade. I am able to code it (see > > below) and > >> > run it in the backtester. The trades correctly get stopped out at > > 20 pips > >> > against. However, new Buys and Shorts do not happen until the > > original, and > >> > now "phantom", Buy or Short runs it's course. So as far as > > entering new > >> > positions is concerned, it's as if the stop command is not even > > there! I > >> > want to enter a new Buy or Short immediately after a stop, so long > > as the > >> > Buy or Short rules are currently true. > >> > > >> > This quirk leads me to believe that some variable is not being reset > >> > correctly. But whether I place the stop command inside the loop or > > out, I > >> > get the same result in the backtester. How do I reset the variables > >> > correctly so that the program is ready to Buy or Sell again as > > soon as a > >> > stop has occured? > >> > > >> > > >> > Sell = Cover = 0; > >> > BuyPrice = SellPrice = ShortPrice = CoverPrice = O; > >> > > >> > myMA1 = MA(C,4); > >> > MyMA2 = MA(C,15); > >> > > >> > Buy = (myMA1 > MyMA2); > >> > Short = (myMA1 < MyMA2); > >> > ApplyStop(0,2,.0020,1); > >> > > >> > > >> > inBuy = inShort = 0; > >> > ValueAtBuy = ValueAtShort = Null; > >> > > >> > for( i = 0; i < BarCount; i++ ) > >> > > >> > { //various sell and cover rules > >> > > >> > } > >> > > >> > Buy = ExRem(Buy, Sell); > >> > Sell = ExRem(Sell, Buy); > >> > Short = ExRem(Short, Cover); > >> > Cover = ExRem(Cover, Short); > >> > SetPositionSize(2,spsShares); > >> > > >> > >
