Mike, Not at all, the examples you provided mirror more less the approaches I tried outside of the loop, the only problem was that those approaches posed a noticeable degradation in the performance of the system! Overall the performance of the system was still quite acceptable except that I thought that by going inside the loop I might get better execution speed.
I greatly appreciate your response, thanks again. --- In [email protected], "Mike" <[EMAIL PROTECTED]> wrote: > > Hi, > > I'll take your word for it, that you need the loop. > > That being said, I don't see that your comments exclude any of the > approaches. It just means that they need to be realigned to include > the current bar. > > Given that you are not altering anything inside your loop (with > respect to the High values), but rather just comparing two > consecutive values (highest of two - the value of which is presumably > then being used later in the loop), there is no need to repeatedly > call HHV in the loop. Just do it once outside the loop and refer to > the resulting elements from inside the loop. Each element of the > result will be the higher of the current and the preceding bar. As > you increment through the loop, you will always be seeing the highest > of the current (i.e. bar at loop counter index) and the previous bar > (i.e. bar at loop counter index - 1). > > You can even pull out your entire HHV/LLV calculation and just refer > to the i-th result inside the loop e.g. > > Result = HHV(High, 2)/LLV(...); > > for (i = 1; i < BarCount; i++) { > ... // Refer to Result[i] here > } > > I believe that any of the following would still give you what you are > after, unless I'm misunderstanding what it is you are trying to do. > > Option 1: > > HighestOfTwo = HHV(High, 2); > > for (i = 1; i < BarCount; i++) { > xyz = HighestOfTwo[i]; // xyz as scaler > ... > } > > Note that this is identical to just saying: > > xyz = HHV(High, 2); // xyz as array > > for (i = 1; i < BarCount; i++) { > ... // refer to xyz[i]. > } > > Option 2: > > HighestOfTwo = Max(High, Ref(High, -1)); > > for (i = 1; i < BarCount; i++) { > xyz = HighestOfTwo[i]; // xyz as scaler > ... > } > > Same xyz as array approach is possible here too. > > Option 3: > > for (i = 1; i < BarCount; i++) { > xyz = High[i]; > if (High[i - 1] > xyz) xyz = High[i - 1]; // highest of 2 incl. > ... > } > > All of the above will leave you, at each bar, with the higher of two > consecutive highs (including the current high) stored in variable > xyz. Is that not what you were trying to achieve? > > I'll withdraw from further replies to allow others to address > anything that I may have missed, unless you specifically have any > question regarding what I've posted to date. > > Mike > > --- In [email protected], "cottondepot" <bill.ghali@> > wrote: > > > > Mike, > > Appreciate that, I do need the looping because my code looks back > > quite a bit. > > > > I also need to include the current bar in my HHV/LLV test because > > I'm setting "Limit Prices" for real-time trading. Obviously HHV/LLV > > on the current bar are snapshots in time rather than true > > reflections of what the high or the low for the bar ends up being. > > > > I'm beginning to reach the conclusion that HHV/LLV because they are > > themselves in a sense "looping arrays" are not that efficient to > use > > inside a loop. > > > > I am indeed testing other approaches however before I give up, I > > wanted to see if anyone else out there had successfully implemented > > HHV/LLV within a loop. > > > > Again, appreciate your attempts. > > > > --- In [email protected], "Mike" <sfclimbers@> wrote: > > > > > > Hi, > > > > > > I haven't tested any of this for accuracy. But, you can play with > > the > > > following approaches, all of which I've tried to keep within the > > > structure of your original code snippet (i.e. assuming that > > looping > > > is necessary). > > > > > > However, as suggested, looping may not be necessary, and likely > is > > > not necessary. > > > > > > If I read HHV correctly, then it will include the current bar in > > the > > > calculation. I'm assuming that you do not want to include the > > current > > > bar when looking at "the last 2 bars", and so have used Ref (..., - > > 1) > > > to exclude the current bar. Double check this. > > > > > > Note too that bar indexing is zero based, so your counter (e.g. i > > = ) > > > needs to be 1 less than you might otherwise expect. > > > > > > Option 1: > > > > > > HighestOfTwo = Ref(HHV(High, 2), -1); > > > > > > for (i = 2; i < BarCount; i++) { > > > xyz = HighestOfTwo[i]; > > > ... > > > } > > > > > > Option 2: > > > > > > HighestOfTwo = Max(Ref(High, -1), Ref(High, -2)); > > > > > > for (i = 2; i < BarCount; i++) { > > > xyz = HighestOfTwo[i]; > > > ... > > > } > > > > > > Option 3: > > > > > > for (i = 2; i < BarCount; i++) { > > > xyz = High[i - 1]; > > > if (High[i - 2] > xyz) xyz = High[i - 2]; > > > ... > > > } > > > > > > Again, things will go significantly faster if you don't need the > > > loops. > > > > > > Mike > > > > > > --- In [email protected], "sidhartha70" <sidhartha70@> > > > wrote: > > > > > > > > Help if we knew the full context of the problem... it is likely > > that > > > > you wouldn't need to use HHV/LLV inside a loop. You can > probably > > > code > > > > the use of HHV/LLV outside of the loop. if you need one at > all... > > > > > > > > > > > > --- In [email protected], "cottondepot" <bill.ghali@> > > wrote: > > > > > > > > > > Need to use HHV/LLV in a loop: > > > > > > > > > > for (i = 3; i < BarCount; i++) > > > > > { > > > > > xyz=HHV(High[i],2); > > > > > ... > > > > > } > > > > > > > > > > Obviously that didn't work. In the loop, I'm trying to use > > > the "High" > > > > > of the last 2 bars as the "LimitPrice" on an order. > > > > > > > > > > Any pointers would be greatly appreciated. > > > > > > > > > > > > > > >
