Hi Frank, Without the USB cable i am able to see the android home screen and play around like a normal android mobile, the kernel crashes only when i insert the usb cable. It is a Omap3530 EVM from Mistral solotions.
Regards, Satish. On Jun 3, 12:38 pm, FrankG <[email protected]> wrote: > Hi Satish, > > an your hardware is from where ? > > What you see finally on the device without usb cable ? > > Good luck ! > > Frank > > On 3 Jun., 06:02, PP <[email protected]> wrote: > > > Hi Frank, > > > Thanks for the reply. > > > The build did not crash without the USB cable. Without the USB cable > > connected to the host, i was able to get the Android boot screen. > > I got the prebuilt images from the site,http://code.google.com/p/rowboat/. > > Could there be some problem with the kernel image of the build? > > Should i download the source and rebuild it ? > > > Regrads,, > > Satish. > > > On Jun 2, 1:30 pm, FrankG <[email protected]> wrote: > > > > Did it crash without the cable ? > > > > From someone you got the flash tool, the details how to flash the > > > devise and I assume > > > also a orginal complete working build for this device. > > > > I would suggest you to a) run the device with the orginal build and > > > save the kernel messages and then b) run your own build and save > > > them and after that compare them to see what can be the problem. > > > > You should also check with modinfo the Kernel Objects (*.ko), maybe > > > "vermagic" > > > is modified through your Source Control System ? > > > > Good luck ! Frank > > > > On 1 Jun., 12:54, PP <[email protected]> wrote: > > > > > Hi All, > > > > > I haveOmap3530evm running Android 2.1. I want to install application > > > > on the evm, so i connected the evm to the host through the USB OTG > > > > cable, but the kernel is crashing. Kindly help me out in sorting this > > > > issue. Find the log below: > > > > > OMAP3_EVM # > > > > OMAP3_EVM # > > > > OMAP3_EVM # setenv bootargs 'init=/init console=ttyS0,115200n8 root=/ > > > > dev/mmcblk > > > > 0p2 rw rootwait mem=256M noinitrd androidboot.console=ttyS0 > > > > mpurate=720' > > > > OMAP3_EVM # setenv bootcmd 'mmcinit; fatload mmc 0 0x80100000 uImage; > > > > bootm 0x80 > > > > 100000' > > > > OMAP3_EVM # boot > > > > reading uImage > > > > > 2489828 bytes read > > > > ## Booting kernel from Legacy Image at 80100000 ... > > > > Image Name: Linux-2.6.32 > > > > Image Type: ARM Linux Kernel Image (uncompressed) > > > > Data Size: 2489764 Bytes = 2.4 MB > > > > Load Address: 80008000 > > > > Entry Point: 80008000 > > > > Verifying Checksum ... OK > > > > Loading Kernel Image ... OK > > > > OK > > > > > Starting kernel ... > > > > > Uncompressing > > > > Linux............................................................. > > > > ................................................................................ > > > > ............... done, booting the kernel. > > > > Linux version 2.6.32 (r...@khasim-laptop) (gcc version 4.4.0 (GCC) ) > > > > #2 Thu May > > > > 20 18:31:19 IST 2010 > > > > CPU: ARMv7 Processor [411fc083] revision 3 (ARMv7), cr=10c53c7f > > > > CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache > > > > Machine: OMAP3 EVM > > > > Memory policy: ECC disabled, Data cache writeback > > > > OMAP3430/3530 ES3.1 (l2cache iva sgx neon isp 720m ) > > > > SRAM: Mapped pa 0x40200000 to va 0xfe400000 size: 0x100000 > > > > Reserving 4194304 bytes SDRAM for VRAM > > > > Built 1 zonelists in Zone order, mobility grouping on. Total pages: > > > > 65024 > > > > Kernel command line: init=/init console=ttyS0,115200n8 root=/dev/ > > > > mmcblk0p2 rw ro > > > > otwait mem=256M noinitrd androidboot.console=ttyS0 mpurate=720 > > > > PID hash table entries: 1024 (order: 0, 4096 bytes) > > > > Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) > > > > Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) > > > > Memory: 256MB = 256MB total > > > > Memory: 250112KB available (4292K code, 825K data, 176K init, 0K > > > > highmem) > > > > Hierarchical RCU implementation. > > > > NR_IRQS:402 > > > > Clocking rate (Crystal/Core/MPU): 26.0/332/500 MHz > > > > Reprogramming SDRC clock to 332000000 Hz > > > > GPMC revision 5.0 > > > > IRQ: Found an INTC at 0xfa200000 (revision 4.0) with 96 interrupts > > > > Total of 96 interrupts on 1 active controller > > > > OMAP GPIO hardware version 2.5 > > > > OMAP clockevent source: GPTIMER1 at 32768 Hz > > > > Console: colour dummy device 80x30 > > > > Calibrating delay loop... 499.92 BogoMIPS (lpj=1949696) > > > > Mount-cache hash table entries: 512 > > > > CPU: Testing write buffer coherency: ok > > > > regulator: core version 0.5 > > > > NET: Registered protocol family 16 > > > > Target VDD1 OPP = 6, VDD2 OPP = 3 > > > > omap3evmdc: Driver registration complete > > > > OMAP DMA hardware revision 4.0 > > > > bio: create slab <bio-0> at 0 > > > > SCSI subsystem initialized > > > > usbcore: registered new interface driver usbfs > > > > usbcore: registered new interface driver hub > > > > usbcore: registered new device driver usb > > > > i2c_omap i2c_omap.1: bus 1 rev3.12 at 2600 kHz > > > > twl4030: PIH (irq 7) chaining IRQs 368..375 > > > > twl4030: power (irq 373) chaining IRQs 376..383 > > > > twl4030: gpio (irq 368) chaining IRQs 384..401 > > > > regulator: VMMC1: 1850 <--> 3150 mV normal standby > > > > regulator: VDAC: 1800 mV normal standby > > > > regulator: VAUX2_4030: 2800 mV normal standby > > > > regulator: VPLL2: 1800 mV normal standby > > > > regulator: VSIM: 1800 <--> 3000 mV normal standby > > > > i2c_omap i2c_omap.2: bus 2 rev3.12 at 400 kHz > > > > i2c_omap i2c_omap.3: bus 3 rev3.12 at 400 kHz > > > > Switching to clocksource 32k_counter > > > > musb_hdrc: version 6.0, musb-dma, otg (peripheral+host), debug=0 > > > > musb_hdrc: USB OTG mode controller at fa0ab000 using DMA, IRQ 92 > > > > musb_hdrc musb_hdrc: MUSB HDRC host driver > > > > musb_hdrc musb_hdrc: new USB bus registered, assigned bus number 1 > > > > usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 > > > > usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 > > > > usb usb1: Product: MUSB HDRC host driver > > > > usb usb1: Manufacturer: Linux 2.6.32 musb-hcd > > > > usb usb1: SerialNumber: musb_hdrc > > > > hub 1-0:1.0: USB hub found > > > > hub 1-0:1.0: 1 port detected > > > > NET: Registered protocol family 2 > > > > IP route cache hash table entries: 2048 (order: 1, 8192 bytes) > > > > TCP established hash table entries: 8192 (order: 4, 65536 bytes) > > > > TCP bind hash table entries: 8192 (order: 3, 32768 bytes) > > > > TCP: Hash tables configured (established 8192 bind 8192) > > > > TCP reno registered > > > > UDP hash table entries: 256 (order: 0, 4096 bytes) > > > > UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) > > > > NET: Registered protocol family 1 > > > > RPC: Registered udp transport module. > > > > RPC: Registered tcp transport module. > > > > RPC: Registered tcp NFSv4.1 backchannel transport module. > > > > omap-iommu omap-iommu.0: isp registered > > > > OMAP35x Linux PSP version 03.00.00.05 (OMAP3EVM) > > > > NetWinder Floating Point Emulator V0.97 (double precision) > > > > ashmem: initialized > > > > VFS: Disk quotas dquot_6.5.2 > > > > Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) > > > > JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc. > > > > msgmni has been set to 488 > > > > alg: No test for stdrng (krng) > > > > io scheduler noop registered > > > > io scheduler deadline registered > > > > io scheduler cfq registered (default) > > > > OMAP DSS rev 2.0 > > > > OMAP DISPC rev 3.0 > > > > OMAP VENC rev 2 > > > > OMAP DSI rev 1.0 > > > > Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled > > > > serial8250.0: ttyS0 at MMIO 0x4806a000 (irq = 72) is a ST16654 > > > > console [ttyS0] enabled > > > > serial8250.1: ttyS1 at MMIO 0x4806c000 (irq = 73) is a ST16654 > > > > serial8250.2: ttyS2 at MMIO 0x49020000 (irq = 74) is a ST16654 > > > > brd: module loaded > > > > loop: module loaded > > > > omap2-nand driver initializing > > > > NAND device: Manufacturer ID: 0x2c, Chip ID: 0xba (Micron NAND 256MiB > > > > 1,8V 16-bi > > > > t) > > > > Creating 5 MTD partitions on "omap2-nand.0": > > > > 0x000000000000-0x000000080000 : "xloader-nand" > > > > 0x000000080000-0x000000240000 : "uboot-nand" > > > > 0x000000240000-0x000000280000 : "params-nand" > > > > 0x000000280000-0x000000780000 : "linux-nand" > > > > 0x000000780000-0x000010000000 : "jffs2-nand" > > > > OneNAND driver initializing > > > > omap2-onenand omap2-onenand: Cannot request GPMC CS > > > > omap2-onenand: probe of omap2-onenand failed with error -16 > > > > smsc911x: Driver version 2008-10-21. > > > > smsc911x-mdio: probed > > > > eth0: attached PHY driver [Generic PHY] (mii_bus:phy_addr=ffffffff:01, > > > > irq=-1) > > > > net eth0: MAC Address: 00:50:c2:7e:91:4a > > > > usbcore: registered new interface driver cdc_ether > > > > usbcore: registered new interface driver dm9601 > > > > ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver > > > > ehci-omap ehci-omap.0: OMAP-EHCI Host Controller > > > > ehci-omap ehci-omap.0: new USB bus registered, assigned bus number 2 > > > > ehci-omap ehci-omap.0: irq 77, io mem 0x48064800 > > > > ehci-omap ehci-omap.0: USB 2.0 started, EHCI 1.00 > > > > usb usb2: New USB device found, idVendor=1d6b, idProduct=0002 > > > > usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 > > > > usb usb2: Product: OMAP-EHCI Host Controller > > > > usb usb2: Manufacturer: Linux 2.6.32 ehci_hcd > > > > usb usb2: SerialNumber: ehci-omap.0 > > > > hub 2-0:1.0: USB hub found > > > > hub 2-0:1.0: 3 ports detected > > > > Initializing USB Mass Storage driver... > > > > usbcore: registered new interface driver usb-storage > > > > USB Mass Storage support registered. > > > > usbcore: registered new interface driver usbtest > > > > android init > > > > f_acm init > > > > android_register_function acm > > > > f_adb init > > > > android_register_function adb > > > > f_mass_storage init > > > > android_register_function usb_mass_storage > > > > f_rndis init > > > > android_register_function rndis > > > > input: TWL4030 Keypad as /devices/platform/i2c_omap.1/i2c-1/1-004a/ > > > > twl4030_keypa > > > > d/input/input0 > > > > ads7846 spi1.0: touchscreen, irq 335 > > > > input: ADS7846 Touchscreen as > > ... > > read more » -- You received this message because you are subscribed to the Google Groups "Android Developers" group. To post to this group, send email to [email protected] To unsubscribe from this group, send email to [email protected] For more options, visit this group at http://groups.google.com/group/android-developers?hl=en
