Hi, David,
I met the same problem in my android 1.5 build. Just as you said, I
cannot find  /system/etc/vold.conf at all. Could you tell me how to
put it into system.img? I tried to copy development/data/etc/vold.conf
to out/target/product/generic/system/etc/vold.conf, and make
system.img again, but it doesn't work.

thx.

On Wed, May 6, 2009 at 9:32 AM, David Turner<[email protected]> wrote:
>
>
> On Tue, May 5, 2009 at 8:50 PM, dan raaka <[email protected]> wrote:
>>
>> I can find that under
>> ./development/data/etc/vold.conf
>
> that is normal, but is the file copied to /system/etc/vold.conf when you run
> the emulator ?
> If not, this explains the empty and read-only /sdcard
>>
>>
>>
>>
>> On Mon, May 4, 2009 at 11:51 PM, David Turner <[email protected]> wrote:
>>>
>>> I guess /system/etc/vold.conf is missing from your build. How did you
>>> configure it ?
>>>
>>> On Mon, May 4, 2009 at 11:51 PM, Marco Nelissen <[email protected]>
>>> wrote:
>>>>
>>>> Well, so what does the system log say? If there's an error mounting the
>>>> card, it's probably going to be logged there.
>>>>
>>>>
>>>>
>>>> On Mon, May 4, 2009 at 2:39 PM, dan raaka <[email protected]> wrote:
>>>>>
>>>>> well .. I wish it was the reason !!
>>>>>
>>>>> $ ls -l out/target/product/generic/sdcard*
>>>>> -rwxrwxrwx 1 mankapur mankapur 67108864 2009-05-01 16:56
>>>>> out/target/product/generic/sdcard.img
>>>>> -rw------- 1 mankapur mankapur        6 2009-05-04 11:22
>>>>> out/target/product/generic/sdcard.img.lock
>>>>>
>>>>> On Mon, May 4, 2009 at 12:55 PM, swarup <[email protected]> wrote:
>>>>>>
>>>>>> well, just a small test shows that when sdcard.img file is RO, it is
>>>>>> not shown in the mount list.
>>>>>> check the below o/p i got from my set up.
>>>>>>
>>>>>> ===========================================
>>>>>> [swa...@~/.android/avd/mydev.avd/]% chmod -w sdcard.img
>>>>>>
>>>>>> [swa...@~/.android/avd/mydev.avd/]% ls -l
>>>>>>
>>>>>> -r--r--r-- 1 swarup swarup 134217728 2009-04-30 23:36 sdcard.img
>>>>>> -rw------- 1 swarup swarup         5 2009-05-05 00:44 sdcard.img.lock
>>>>>>
>>>>>> [swa...@~/.android/avd/mydev.avd/]% emu #run emulator
>>>>>>
>>>>>> [swa...@~/.android/avd/mydev.avd/]% adb shell mount
>>>>>>
>>>>>> rootfs / rootfs ro 0 0
>>>>>> tmpfs /dev tmpfs rw,mode=755 0 0
>>>>>> devpts /dev/pts devpts rw,mode=600 0 0
>>>>>> proc /proc proc rw 0 0
>>>>>> sysfs /sys sysfs rw 0 0
>>>>>> tmpfs /sqlite_stmt_journals tmpfs rw,size=4096k 0 0
>>>>>> /dev/block/mtdblock0 /system yaffs2 ro 0 0
>>>>>> /dev/block/mtdblock1 /data yaffs2 rw,nosuid,nodev 0 0
>>>>>> /dev/block/mtdblock2 /cache yaffs2 rw,nosuid,nodev 0 0
>>>>>>
>>>>>> [swa...@~/.android/avd/mydev.avd/]% chmod +w sdcard.img
>>>>>>
>>>>>> [swa...@~/.android/avd/mydev.avd/]% ls -l
>>>>>>
>>>>>> -rw-r--r-- 1 swarup swarup 134217728 2009-04-30 23:36 sdcard.img
>>>>>> -rw------- 1 swarup swarup         6 2009-05-05 01:14 sdcard.img.lock
>>>>>>
>>>>>> [swa...@~/.android/avd/mydev.avd/]% emu #run emulator
>>>>>>
>>>>>> [swa...@~/.android/avd/mydev.avd/]% adb shell mount
>>>>>>
>>>>>> rootfs / rootfs ro 0 0
>>>>>> tmpfs /dev tmpfs rw,mode=755 0 0
>>>>>> devpts /dev/pts devpts rw,mode=600 0 0
>>>>>> proc /proc proc rw 0 0
>>>>>> sysfs /sys sysfs rw 0 0
>>>>>> tmpfs /sqlite_stmt_journals tmpfs rw,size=4096k 0 0
>>>>>> /dev/block/mtdblock0 /system yaffs2 ro 0 0
>>>>>> /dev/block/mtdblock1 /data yaffs2 rw,nosuid,nodev 0 0
>>>>>> /dev/block/mtdblock2 /cache yaffs2 rw,nosuid,nodev 0 0
>>>>>> /dev/block//vold/179:0 /sdcard vfat
>>>>>>
>>>>>> rw,dirsync,nosuid,nodev,noexec,uid=1000,gid=1000,fmask=0711,dmask=0700,allow_utime=0022,codepage=cp437,iocharset=iso8859-1,shortname=mixed,utf8
>>>>>> 0 0
>>>>>>
>>>>>> [swa...@~/.android/avd/mydev.avd/]%
>>>>>>
>>>>>> ===========================================
>>>>>> On May 5, 12:42 am, swarup <[email protected]> wrote:
>>>>>> > yes Marco, you are write, even for RO sdcard.img files, it should be
>>>>>> > visible for 'mount' command.
>>>>>> > recreation of the sdcard.img might help in resolving the issue.
>>>>>> >
>>>>>> > On May 5, 12:21 am, Marco Nelissen <[email protected]> wrote:
>>>>>> >
>>>>>> > > As long as you run the emulator as the user 'owner', it should be
>>>>>> > > writable.
>>>>>> > > And again: the problem is not that it's mounted read-only, it's
>>>>>> > > that it's
>>>>>> > > not mounted at all.
>>>>>> > > Your dmesg seems to indicate that no partition was found in your
>>>>>> > > image. What
>>>>>> > > does the system log say? (logcat)
>>>>>> >
>>>>>> > > On Mon, May 4, 2009 at 12:18 PM, swarup <[email protected]> wrote:
>>>>>> >
>>>>>> > > > check the permissions of the ./sdcard.img file.
>>>>>> > > > does it have write permission??
>>>>>> >
>>>>>> > > > -rw-r--r-- 1 owner owner 134217728 2009-04-30 23:36 sdcard.img
>>>>>> >
>>>>>> > > > On May 4, 11:59 pm, dan raaka <[email protected]> wrote:
>>>>>> > > > > Here goes the dmesg log
>>>>>> >
>>>>>> > > > > $ adb shell dmesg
>>>>>> > > > > <5>Linux version 2.6.27-00110-g132305e (
>>>>>> > > > [email protected])
>>>>>> > > > > (gcc version 4.2.1) #6 Mon Feb 2 12:47:38 PST 2009
>>>>>> > > > > <4>CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ),
>>>>>> > > > > cr=00093177
>>>>>> > > > > <4>Machine: Goldfish
>>>>>> > > > > <4>Memory policy: ECC disabled, Data cache writeback
>>>>>> > > > > <7>On node 0 totalpages: 24576
>>>>>> > > > > <7>free_area_init_node: node 0, pgdat c0294734, node_mem_map
>>>>>> > > > > c031e000
>>>>>> > > > > <7>  DMA zone: 24384 pages, LIFO batch:3
>>>>>> > > > > <4>CPU0: D VIVT write-through cache
>>>>>> > > > > <4>CPU0: I cache: 4096 bytes, associativity 4, 32 byte lines,
>>>>>> > > > > 32 sets
>>>>>> > > > > <4>CPU0: D cache: 65536 bytes, associativity 4, 32 byte lines,
>>>>>> > > > > 512 sets
>>>>>> > > > > <4>Built 1 zonelists in Zone order, mobility grouping on.
>>>>>> > > > >  Total pages:
>>>>>> > > > > 24384
>>>>>> > > > > <5>Kernel command line: qemu=1 console=ttyS0
>>>>>> > > > > android.checkjni=1
>>>>>> > > > > android.qemud=ttyS1 android.ndns=1
>>>>>> > > > > <3>Unknown boot option `android.checkjni=1': ignoring
>>>>>> > > > > <3>Unknown boot option `android.qemud=ttyS1': ignoring
>>>>>> > > > > <3>Unknown boot option `android.ndns=1': ignoring
>>>>>> > > > > <4>PID hash table entries: 512 (order: 9, 2048 bytes)
>>>>>> > > > > <4>Console: colour dummy device 80x30
>>>>>> > > > > <6>Dentry cache hash table entries: 16384 (order: 4, 65536
>>>>>> > > > > bytes)
>>>>>> > > > > <6>Inode-cache hash table entries: 8192 (order: 3, 32768
>>>>>> > > > > bytes)
>>>>>> > > > > <6>Memory: 96MB = 96MB total
>>>>>> > > > > <5>Memory: 94040KB available (2408K code, 640K data, 104K
>>>>>> > > > > init)
>>>>>> > > > > <6>Calibrating delay loop... 104.65 BogoMIPS (lpj=523264)
>>>>>> > > > > <4>Mount-cache hash table entries: 512
>>>>>> > > > > <6>CPU: Testing write buffer coherency: ok
>>>>>> > > > > <6>net_namespace: 288 bytes
>>>>>> > > > > <6>NET: Registered protocol family 16
>>>>>> > > > > <7>Switched to high resolution mode on CPU 0
>>>>>> > > > > <6>NET: Registered protocol family 2
>>>>>> > > > > <6>IP route cache hash table entries: 1024 (order: 0, 4096
>>>>>> > > > > bytes)
>>>>>> > > > > <6>TCP established hash table entries: 4096 (order: 3, 32768
>>>>>> > > > > bytes)
>>>>>> > > > > <6>TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
>>>>>> > > > > <6>TCP: Hash tables configured (established 4096 bind 4096)
>>>>>> > > > > <6>TCP reno registered
>>>>>> > > > > <6>NET: Registered protocol family 1
>>>>>> > > > > <6>checking if image is initramfs... it is
>>>>>> > > > > <6>Freeing initrd memory: 142K
>>>>>> > > > > <4>goldfish_new_pdev goldfish_interrupt_controller at ff000000
>>>>>> > > > > irq -1
>>>>>> > > > > <4>goldfish_new_pdev goldfish_device_bus at ff001000 irq 1
>>>>>> > > > > <4>goldfish_new_pdev goldfish_timer at ff003000 irq 3
>>>>>> > > > > <4>goldfish_new_pdev goldfish_rtc at ff010000 irq 10
>>>>>> > > > > <4>goldfish_new_pdev goldfish_tty at ff002000 irq 4
>>>>>> > > > > <4>goldfish_new_pdev goldfish_tty at ff011000 irq 11
>>>>>> > > > > <4>goldfish_new_pdev smc91x at ff012000 irq 12
>>>>>> > > > > <4>goldfish_new_pdev goldfish_fb at ff013000 irq 13
>>>>>> > > > > <4>goldfish_new_pdev goldfish_audio at ff004000 irq 14
>>>>>> > > > > <4>goldfish_new_pdev goldfish_mmc at ff005000 irq 15
>>>>>> > > > > <4>goldfish_new_pdev goldfish_memlog at ff006000 irq -1
>>>>>> > > > > <4>goldfish_new_pdev goldfish-battery at ff014000 irq 16
>>>>>> > > > > <4>goldfish_new_pdev goldfish_events at ff015000 irq 17
>>>>>> > > > > <4>goldfish_new_pdev goldfish_nand at ff016000 irq -1
>>>>>> > > > > <4>goldfish_new_pdev goldfish-switch at ff017000 irq 18
>>>>>> > > > > <4>goldfish_new_pdev goldfish-switch at ff018000 irq 19
>>>>>> > > > > <4>goldfish_pdev_worker registered goldfish-switch
>>>>>> > > > > <4>goldfish_pdev_worker registered goldfish-switch
>>>>>> > > > > <4>goldfish_pdev_worker registered goldfish_nand
>>>>>> > > > > <4>goldfish_pdev_worker registered goldfish_events
>>>>>> > > > > <4>goldfish_pdev_worker registered goldfish-battery
>>>>>> > > > > <4>goldfish_pdev_worker registered goldfish_memlog
>>>>>> > > > > <4>goldfish_pdev_worker registered goldfish_mmc
>>>>>> > > > > <4>goldfish_audio_probe
>>>>>> > > > > <4>goldfish_pdev_worker registered goldfish_audio
>>>>>> > > > > <4>goldfish_pdev_worker registered goldfish_fb
>>>>>> > > > > <4>goldfish_pdev_worker registered smc91x
>>>>>> > > > > <4>goldfish_pdev_worker registered goldfish_tty
>>>>>> > > > > <4>goldfish_pdev_worker registered goldfish_tty
>>>>>> > > > > <4>goldfish_pdev_worker registered goldfish_rtc
>>>>>> > > > > <4>goldfish_pdev_worker registered goldfish_timer
>>>>>> > > > > <4>goldfish_pdev_worker registered goldfish_device_bus
>>>>>> > > > > <4>goldfish_pdev_worker registered
>>>>>> > > > > goldfish_interrupt_controller
>>>>>> > > > > <6>ashmem: initialized
>>>>>> > > > > <6>Installing knfsd (copyright (C) 1996 [email protected]).
>>>>>> > > > > <4>yaffs Feb  2 2009 12:47:30 Installing.
>>>>>> > > > > <6>msgmni has been set to 184
>>>>>> > > > > <6>io scheduler noop registered
>>>>>> > > > > <6>io scheduler anticipatory registered (default)
>>>>>> > > > > <6>io scheduler deadline registered
>>>>>> > > > > <6>io scheduler cfq registered
>>>>>> > > > > <4>allocating frame buffer 320 * 480, got ffc10000
>>>>>> > > > > <4>Console: switching to colour frame buffer device 40x30
>>>>>> > > > > <6>console [ttyS0] enabled
>>>>>> > > > > <6>brd: module loaded
>>>>>> > > > > <6>loop: module loaded
>>>>>> > > > > <6>nbd: registered device at major 43
>>>>>> > > > > <6>logger: created 64K log 'log_main'
>>>>>> > > > > <6>logger: created 256K log 'log_events'
>>>>>> > > > > <6>logger: created 64K log 'log_radio'
>>>>>> > > > > <4>smc91x.c: v1.1, sep 22 2004 by Nicolas Pitre <[email protected]>
>>>>>> > > > > <4>No set_type function for IRQ 12 (goldfish)
>>>>>> > > > > <4>eth0: SMC91C11xFD (rev 1) at c6800000 IRQ 12 [nowait]
>>>>>> > > > > <4>eth0: Ethernet addr: 52:54:00:12:34:56
>>>>>> > > > > <7>eth0: No PHY found
>>>>>> > > > > <4>goldfish nand dev0: size 4000000, page 2048, extra 64,
>>>>>> > > > > erase 131072
>>>>>> > > > > <4>goldfish nand dev1: size 4000000, page 2048, extra 64,
>>>>>> > > > > erase 131072
>>>>>> > > > > <4>goldfish nand dev2: size 4000000, page 2048, extra 64,
>>>>>> > > > > erase 131072
>>>>>> > > > > <6>mice: PS/2 mouse device common for all mice
>>>>>> > > > > <4>*** events probe ***
>>>>>> > > > > <4>events_probe() addr=0xc6804000 irq=17
>>>>>> > > > > <4>events_probe() keymap=qwerty2
>>>>>> > > > > <6>input: qwerty2 as /devices/virtual/input/input0
>>>>>> > > > > <6>goldfish_rtc goldfish_rtc: rtc core: registered
>>>>>> > > > > goldfish_rtc as rtc0
>>>>>> > > > > <6>mmc0: new SD card at address e118
>>>>>> > > > > <6>mmcblk0: mmc0:e118 SU02G 65536KiB
>>>>>> > > > > <6> mmcblk0:
>>>>>> > > > > <6>IPv4 over IPv4 tunneling driver
>>>>>> > > > > <6>GRE over IPv4 tunneling driver
>>>>>> > > > > <6>TCP cubic registered
>>>>>> > > > > <6>NET: Registered protocol family 17
>>>>>> > > > > <6>RPC: Registered udp transport module.
>>>>>> > > > > <6>RPC: Registered tcp transport module.
>>>>>> > > > > <6>802.1Q VLAN Support v1.8 Ben Greear
>>>>>> > > > > <[email protected]>
>>>>>> > > > > <6>All bugs added by David S. Miller <[email protected]>
>>>>>> > > > > <6>VFP support v0.3: implementor 41 architecture 1 part 10
>>>>>> > > > > variant 9 rev
>>>>>> > > > 0
>>>>>> > > > > <6>goldfish_rtc goldfish_rtc: setting system clock to
>>>>>> > > > > 2009-05-04 18:22:33
>>>>>> > > > > UTC (1241461353)
>>>>>> > > > > <6>Freeing init memory: 104K
>>>>>> > > > > <3>init: cannot open '/initlogo.rle'
>>>>>> > > > > <6>yaffs: dev is 32505856 name is "mtdblock0"
>>>>>> > > > > <6>yaffs: passed flags ""
>>>>>> > > > > <4>yaffs: Attempting MTD mount on 31.0, "mtdblock0"
>>>>>> > > > > <4>yaffs_read_super: isCheckpointed 0
>>>>>> > > > > <4>save exit: isCheckpointed 1
>>>>>> > > > > <6>yaffs: dev is 32505857 name is "mtdblock1"
>>>>>> > > > > <6>yaffs: passed flags ""
>>>>>> > > > > <4>yaffs: Attempting MTD mount on 31.1, "mtdblock1"
>>>>>> > > > > <4>yaffs_read_super: isCheckpointed 0
>>>>>> > > > > <6>yaffs: dev is 32505858 name is "mtdblock2"
>>>>>> > > > > <6>yaffs: passed flags ""
>>>>>> > > > > <4>yaffs: Attempting MTD mount on 31.2, "mtdblock2"
>>>>>> > > > > <4>yaffs_read_super: isCheckpointed 0
>>>>>> > > > > <3>init: cannot find '/system/bin/playmp3', disabling
>>>>>> > > > > 'bootsound'
>>>>>> > > > > <6>eth0: link up
>>>>>> > > > > <6>warning: `rild' uses 32-bit capabilities (legacy support in
>>>>>> > > > > use)
>>>>>> > > > > <4>select 651 (app_process), adj 15, size 3194, to kill
>>>>>> > > > > <4>select 861 (app_process), adj 15, size 3547, to kill
>>>>>> > > > > <4>send sigkill to 861 (app_process), adj 15, size 3547
>>>>>> > > > > <4>select 741 (app_process), adj 15, size 2916, to kill
>>>>>> > > > > <4>send sigkill to 741 (app_process), adj 15, size 2916
>>>>>> > > > > <4>select 1301 (app_process), adj 15, size 4149, to kill
>>>>>> > > > > <4>send sigkill to 1301 (app_process), adj 15, size 4149
>>>>>> >
>>>>>> > > > > On Mon, May 4, 2009 at 11:53 AM, Marco Nelissen
>>>>>> > > > > <[email protected]>
>>>>>> > > > wrote:
>>>>>> > > > > > Look in the system log or dmesg.
>>>>>> >
>>>>>> > > > > > On Mon, May 4, 2009 at 11:39 AM, dan raaka
>>>>>> > > > > > <[email protected]> wrote:
>>>>>> >
>>>>>> > > > > >> Well the verbose output from the emulator doesn't show
>>>>>> > > > > >> anything
>>>>>> > > > obvious
>>>>>> >
>>>>>> > > > > >> $ emulator -sdcard ./sdcard.img -scale 0.75 -verbose&
>>>>>> > > > > >> [2] 21528
>>>>>> > > > > >> emulator: found Android build root:
>>>>>> > > > /home/danraaka/BuildDir/cupcakeFinal
>>>>>> > > > > >> emulator: found Android build out:
>>>>>> > > > > >>
>>>>>> > > > > >> /home/danraaka/BuildDir/cupcakeFinal/out/target/product/generic
>>>>>> > > > > >> emulator:     locking user data image at
>>>>>> >
>>>>>> > > >
>>>>>> > > > /home/danraaka/BuildDir/cupcakeFinal/out/target/product/generic/userdata-qemu.img
>>>>>> > > > > >> emulator:     locking SD Card image at ./sdcard.img
>>>>>> > > > > >> emulator: selecting default skin name 'HVGA'
>>>>>> > > > > >> emulator: autoconfig: -skin HVGA
>>>>>> > > > > >> emulator: autoconfig: -skindir
>>>>>> > > > > >>
>>>>>> > > > > >> /home/danraaka/BuildDir/cupcakeFinal/development/emulator/skins
>>>>>> > > > > >> emulator: keyset loaded from:
>>>>>> > > > > >> /home/danraaka/.android/default.keyset
>>>>>> > > > > >> emulator: trying to load skin file
>>>>>> >
>>>>>> > > >
>>>>>> > > > '/home/danraaka/BuildDir/cupcakeFinal/development/emulator/skins/HVGA/layout
>>>>>> > > > > >> '
>>>>>> > > > > >> emulator: skin network speed: 'full'
>>>>>> > > > > >> emulator: skin network delay: 'none'
>>>>>> > > > > >> emulator: argv[00] = "emulator"
>>>>>> > > > > >> emulator: argv[01]
>>>>>> >
>>>>>> > ...
>>>>>> >
>>>>>> > read more »
>>>>>>
>>>>>
>>>>>
>>>>>
>>>>
>>>>
>>>>
>>>
>>>
>>>
>>
>>
>>
>
>
> >
>



-- 
-- Prajnashi S

--~--~---------~--~----~------------~-------~--~----~
You received this message because you are subscribed to the Google
Groups "Android Developers" group.
To post to this group, send email to [email protected]
To unsubscribe from this group, send email to
[email protected]
For more options, visit this group at
http://groups.google.com/group/android-developers?hl=en
-~----------~----~----~----~------~----~------~--~---

Reply via email to