On Thu, Sep 1, 2011 at 11:00 AM, venkat k raju <[email protected]> wrote:
> Hi Tiago Maluta, > > thanks for your response. > > i am using beagletouch board. > > i made some changes in my boot argument like this > > > there are my environment variable > bootcmd=nand read 0x80300000 280000 400000 ; bootm 0x80300000 > bootargs=console=ttyS2,115200n8 root=/dev/mtdblock4 rootfstype=jffs2 ro > rootwait nohz=off init=/init omapfb.mode=lcd:480x270MR-24@60 > bootdelay=2 > > now there is no Kernel panic error, but it's not mounting filesystem. > please check my log message. > > > > boot > > NAND read: device 0 offset 0x280000, size 0x400000 > 4194304 bytes read: OK > ## Booting kernel from Legacy Image at 80300000 ... > Image Name: Linux-2.6.32 > Image Type: ARM Linux Kernel Image (uncompressed) > Data Size: 2806004 Bytes = 2.7 MiB > Load Address: 80008000 > Entry Point: 80008000 > Verifying Checksum ... OK > Loading Kernel Image ... OK > OK > > Starting kernel ... > > Uncompressing > Linux.................................................................................................................................................... > Linux version 2.6.32 ([email protected]) (gcc version 4.4.0 > (GCC) ) #87 Thu Aug 18 12:36:50 IST 2011 > CPU: ARMv7 Processor [411fc083] revision 3 (ARMv7), cr=10c53c7f > CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache > Machine: OMAP3 Beagle Board > Memory policy: ECC disabled, Data cache writeback > OMAP3430/3530 ES3.1 (l2cache iva sgx neon isp 720m ) > SRAM: Mapped pa 0x40200000 to va 0xfe400000 size: 0x100000 > Reserving 4194304 bytes SDRAM for VRAM > Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024 > Kernel command line: console=ttyS2,115200n8 root=/dev/mtdblock4 > rootfstype=jffs2 ro rootwait nohz=off init=/init > omapfb.mode=lcd:480x270MR-24@60 > PID hash table entries: 1024 (order: 0, 4096 bytes) > Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) > Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) > Memory: 128MB 128MB = 256MB total > Memory: 249472KB available (4932K code, 867K data, 172K init, 0K highmem) > Hierarchical RCU implementation. > NR_IRQS:402 > Clocking rate (Crystal/Core/MPU): 26.0/332/500 MHz > Reprogramming SDRC clock to 332000000 Hz > GPMC revision 5.0 > IRQ: Found an INTC at 0xfa200000 (revision 4.0) with 96 interrupts > Total of 96 interrupts on 1 active controller > OMAP GPIO hardware version 2.5 > OMAP clockevent source: GPTIMER12 at 32768 Hz > Console: colour dummy device 80x30 > Calibrating delay loop... 477.86 BogoMIPS (lpj=1863680) > Mount-cache hash table entries: 512 > CPU: Testing write buffer coherency: ok > regulator: core version 0.5 > NET: Registered protocol family 16 > Found NAND on CS0 > Registering NAND on CS0 > Unable to get DVI reset GPIO > OMAP DMA hardware revision 4.0 > bio: create slab <bio-0> at 0 > SCSI subsystem initialized > usbcore: registered new interface driver usbfs > usbcore: registered new interface driver hub > usbcore: registered new device driver usb > i2c_omap i2c_omap.1: bus 1 rev3.12 at 2600 kHz > twl4030: PIH (irq 7) chaining IRQs 368..375 > twl4030: power (irq 373) chaining IRQs 376..383 > twl4030: gpio (irq 368) chaining IRQs 384..401 > regulator: VUSB1V5: 1500 mV normal standby > regulator: VUSB1V8: 1800 mV normal standby > regulator: VUSB3V1: 3100 mV normal standby > twl4030_usb twl4030_usb: Initialized TWL4030 USB module > regulator: VMMC1: 1850 <--> 3150 mV normal standby > regulator: VDAC: 1800 mV normal standby > regulator: VPLL2: 1800 mV normal standby > regulator: VSIM: 1800 <--> 3000 mV normal standby > i2c_omap i2c_omap.2: bus 2 rev3.12 at 400 kHz > i2c_omap i2c_omap.3: bus 3 rev3.12 at 100 kHz > Switching to clocksource 32k_counter > musb_hdrc: version 6.0, musb-dma, otg (peripheral+host), debug=0 > musb_hdrc: USB OTG mode controller at fa0ab000 using DMA, IRQ 92 > NET: Registered protocol family 2 > IP route cache hash table entries: 2048 (order: 1, 8192 bytes) > TCP established hash table entries: 8192 (order: 4, 65536 bytes) > TCP bind hash table entries: 8192 (order: 3, 32768 bytes) > TCP: Hash tables configured (established 8192 bind 8192) > TCP reno registered > UDP hash table entries: 256 (order: 0, 4096 bytes) > UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) > NET: Registered protocol family 1 > RPC: Registered udp transport module. > RPC: Registered tcp transport module. > RPC: Registered tcp NFSv4.1 backchannel transport module. > omap-iommu omap-iommu.0: isp registered > NetWinder Floating Point Emulator V0.97 (double precision) > ashmem: initialized > VFS: Disk quotas dquot_6.5.2 > Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) > JFFS2 version 2.2. (NAND) �© 2001-2006 Red Hat, Inc. > yaffs Aug 18 2011 12:32:48 Installing. > msgmni has been set to 487 > alg: No test for stdrng (krng) > io scheduler noop registered > io scheduler deadline registered > io scheduler cfq registered (default) > OMAP DSS rev 2.0 > OMAP DISPC rev 3.0 > OMAP VENC rev 2 > cmel_oled43_panel: init panel > cmel_oled43_panel: requesting GPIOs > Registered led device: lcd-backlight > cmel_oled43_panel: done > Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled > serial8250.0: ttyS0 at MMIO 0x4806a000 (irq = 72) is a ST16654 > serial8250.1: ttyS1 at MMIO 0x4806c000 (irq = 73) is a ST16654 > serial8250.2: ttyS2 at MMIO 0x49020000 (irq = 74) is a ST16654 > console [ttyS2] enabled > brd: module loaded > loop: module loaded > usbcore: registered new interface driver asix > usbcore: registered new interface driver cdc_ether > usbcore: registered new interface driver cdc_eem > usbcore: registered new interface driver dm9601 > usbcore: registered new interface driver smsc95xx > usbcore: registered new interface driver gl620a > usbcore: registered new interface driver net1080 > usbcore: registered new interface driver plusb > usbcore: registered new interface driver rndis_host > usbcore: registered new interface driver cdc_subset > usbcore: registered new interface driver zaurus > usbcore: registered new interface driver MOSCHIP usb-ethernet driver > ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver > ehci-omap ehci-omap.0: OMAP-EHCI Host Controller > ehci-omap ehci-omap.0: new USB bus registered, assigned bus number 1 > ehci-omap ehci-omap.0: irq 77, io mem 0x48064800 > ehci-omap ehci-omap.0: USB 2.0 started, EHCI 1.00 > hub 1-0:1.0: USB hub found > hub 1-0:1.0: 3 ports detected > Initializing USB Mass Storage driver... > usbcore: registered new interface driver usb-storage > USB Mass Storage support registered. > android init > android_probe pdata: c053748c > android_bind > android_usb gadget: android_usb ready > musb_hdrc musb_hdrc: MUSB HDRC host driver > musb_hdrc musb_hdrc: new USB bus registered, assigned bus number 2 > hub 2-0:1.0: USB hub found > hub 2-0:1.0: 1 port detected > f_adb init > android_register_function adb > adb_bind_config > f_mass_storage init > android_register_function usb_mass_storage > mice: PS/2 mouse device common for all mice > input: gpio-keys as /devices/platform/gpio-keys/input/input0 > input: TSC2007 Touchscreen as /devices/virtual/input/input1 > i2c /dev entries driver > Linux video capture interface: v2.00 > omap-iommu omap-iommu.0: isp: version 1.1 > gspca: main v2.8.0 registered > usbcore: registered new interface driver conex > conex: registered > usbcore: registered new interface driver etoms > etoms: registered > usbcore: registered new interface driver finepix > finepix: registered > usbcore: registered new interface driver jeilinj > jeilinj: registered > usbcore: registered new interface driver mars > mars: registered > usbcore: registered new interface driver mr97310a > mr97310a: registered > usbcore: registered new interface driver ov519 > ov519: registered > usbcore: registered new interface driver ov534 > ov534: registered > usbcore: registered new interface driver pac207 > pac207: registered > usbcore: registered new interface driver pac7302 > pac7302: registered > usbcore: registered new interface driver pac7311 > pac7311: registered > usbcore: registered new interface driver sn9c20x > sn9c20x: registered > usbcore: registered new interface driver sonixb > sonixb: registered > usbcore: registered new interface driver sonixj > sonixj: registered > usbcore: registered new interface driver spca500 > spca500: registered > usbcore: registered new interface driver spca501 > spca501: registered > usbcore: registered new interface driver spca505 > spca505: registered > usbcore: registered new interface driver spca506 > spca506: registered > usbcore: registered new interface driver spca508 > spca508: registered > usbcore: registered new interface driver spca561 > spca561: registered > usbcore: registered new interface driver sq905 > sq905: registered > usbcore: registered new interface driver sq905c > sq905c: registered > usbcore: registered new interface driver sunplus > sunplus: registered > usbcore: registered new interface driver stk014 > stk014: registered > usbcore: registered new interface driver stv0680 > stv0680: registered > usbcore: registered new interface driver t613 > t613: registered > usbcore: registered new interface driver tv8532 > tv8532: registered > usbcore: registered new interface driver vc032x > vc032x: registered > usbcore: registered new interface driver zc3xx > zc3xx: registered > usbcore: registered new interface driver ALi m5602 > ALi m5602: registered > usbcore: registered new interface driver STV06xx > STV06xx: registered > gspca_gl860: driver startup - version 0.9d10 > usbcore: registered new interface driver gspca_gl860 > gspca_gl860: driver registered > usbcore: registered new interface driver uvcvideo > USB Video Class driver (v0.1.0) > OMAP Watchdog Timer Rev 0x31: initial timeout 60 sec > mmci-omap-hs mmci-omap-hs.1: err -16 configuring card detect > Registered led device: beagleboard::usr0 > Registered led device: beagleboard::usr1 > Registered led device: beagleboard::pmu_stat > usbcore: registered new interface driver usbhid > usbhid: USB HID core driver > logger: created 64K log 'log_main' > logger: created 256K log 'log_events' > logger: created 64K log 'log_radio' > logger: created 64K log 'log_system' > Advanced Linux Sound Architecture Driver Version 1.0.21. > usbcore: registered new interface driver snd-usb-audio > No device for DAI omap-mcbsp-dai-0 > No device for DAI omap-mcbsp-dai-1 > No device for DAI omap-mcbsp-dai-2 > No device for DAI omap-mcbsp-dai-3 > No device for DAI omap-mcbsp-dai-4 > OMAP3 Beagle SoC init > asoc: twl4030 <-> omap-mcbsp-dai-0 mapping ok > ALSA device list: > #0: omap3beagle (twl4030) > TCP cubic registered > NET: Registered protocol family 17 > NET: Registered protocol family 15 > Power Management for TI OMAP3. > SmartReflex driver initialized > VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 1 > fbcvt: 480x270@60: CVT Name - .129M9-R > Console: switching to colour frame buffer device 60x33 > cmel_oled43_panel: panel_enable begin > cmel_oled43_panel: Setting brightness to 100 percent > cmel_oled43_panel: panel_enable end > regulator_init_complete: incomplete constraints, leaving VDVI on > regulator_init_complete: incomplete constraints, leaving VDAC on > drivers/rtc/hctosys.c: unable to open rtc device (rtc0) > omapdss DPI error: display already enabled > omap_vout omap_vout: 'lcd' Display already enabled > omapdss DPI error: display already enabled > omap_vout omap_vout: 'lcd' Display already enabled > omap_vout omap_vout: Buffer Size = 3686400 > omap_vout omap_vout: : registered and initialized video device 0 > omap_vout omap_vout: Buffer Size = 3686400 > omap_vout omap_vout: : registered and initialized video device 1 > Waiting for root device /dev/mtdblock4.. // here it self stopping > > > please suggest me . > > thanks in advacne. > > > > > > On Wed, Aug 31, 2011 at 11:56 PM, Tiago Maluta <[email protected]>wrote: > >> On Wed, Aug 31, 2011 at 5:56 AM, venkat k raju <[email protected]> >> wrote: >> > Hi all, >> > >> > i have been trying to flash the x-load,u-boot,uimage,rootfs.jffs2 to >> nand >> > using windows flash tool Flash v1.5 tool. >> > >> > running the following are no problem those are executing properly. >> > x-loader,u-boot,uImage >> > >> > but rootfs.jffs2 mounting time i got some error like this >> > >> > Root-NFS: No NFS server available, giving up. >> > VFS: Unable to mount root fs via NFS, trying floppy. >> > List of all partitions: >> > No filesystem could mount root, tried: jffs2 >> > Kernel panic - not syncing: VFS: Unable to mount root fs on >> > unknown-block(2,0) >> > >> > here may be problem with "boot arguments" and mount point like from >> where >> > to mount the rootfs. >> > >> > please suggest me how to set the boot arguments, and i don't know how to >> > create mount point from that flash tool or any other approach to solve >> my >> > problem. >> > >> >> what's in your u-boot environment vars? (use "printenv" command) >> >> --tm >> > > > > -- > thanks&Regards > k.v.raju > -- thanks&Regards k.v.raju -- You received this message because you are subscribed to the Google Groups "Android Discuss" group. To post to this group, send email to [email protected]. To unsubscribe from this group, send email to [email protected]. For more options, visit this group at http://groups.google.com/group/android-discuss?hl=en.
