hi Have you set the permission for data and system. from the following lines from your logs permissions 3>init: Unable to open persistent property directory /data/property errno: 2 init: Unable to open persistent property directory /data/property errno: 2
Do the following as root or sudo $cd ~/Android_rfs $chown -R root.root * $chmod -R 777 data system regards haritha 2009/3/31 cindy_king_1024 <[email protected]> > Hi, > I have follow the stepls of the links,but it come to these errors in the > terminal: > > <6>Disabling unused clock "dpll4_m5x2_ck" > Disabling unused clock "dpll4_m5x2_ck" > <6>Disabling unused clock "dpll3_m3x2_ck" > Disabling unused clock "dpll3_m3x2_ck" > <6>Disabling unused clock "sys_clkout1" > Disabling unused clock "sys_clkout1" > <6>VFP support v0.3: VFP support v0.3: implementor 41 architecture 3 part > 30 variant c rev 1 > implementor 41 architecture 3 part 30 variant c rev 1 > drivers/rtc/hctosys.c: unable to open rtc device (rtc0) > drivers/rtc/hctosys.c: unable to open rtc device (rtc0) > <6>eth0: link down > eth0: link down > <5>Sending DHCP requests .Sending DHCP requests .<6>eth0: link up, 100Mbps, > full-duplex, lpa 0x05E1 > <6>eth0: link up, 100Mbps, full-duplex, lpa 0x05E1 > ..,, OK > OK > IP-Config: Got DHCP answer from 0.0.0.0, IP-Config: Got DHCP answer from > 0.0.0.0, my address is 192. > 168.1.104 > my address is 192.168.1.104 > IP-Config: Complete:IP-Config: Complete: > device=eth0 > device=eth0, addr=192.168.1.104, addr=192.168.1.104, > mask=255.255.255.0, mask=255.255.255.0, gw > =192.168.1.1, gw=192.168.1.1, > host=192.168.1.104, domain=domain, nis-domain=(none), > host=192.168.1.104, domain=domain, nis-domain=(none), > bootserver=0.0.0.0, > bootserver=0.0.0.0, rootserver=192.168.1.105, > rootserver=192.168.1.105, rootpath=, rootpath= > <6>Waiting 2sec before mounting root device... > Waiting 2sec before mounting root device... > <5>Looking up port of RPC 100003/2 on 192.168.1.105 > Looking up port of RPC 100003/2 on 192.168.1.105 > <5>Looking up port of RPC 100005/1 on 192.168.1.105 > Looking up port of RPC 100005/1 on 192.168.1.105 > VFS: Mounted root (nfs filesystem). > VFS: Mounted root (nfs filesystem). > <6>Freeing init memory: 144K > Freeing init memory: 144K > <4>Warning: unable to open an initial console. > Warning: unable to open an initial console. > <3>init: cannot open '/initlogo.rle' > init: cannot open '/initlogo.rle' > <3>init: Unable to open persistent property directory /data/property errno: > 2 > init: Unable to open persistent property directory /data/property errno: 2 > <3>init: cannot find '/system/bin/playmp3', disabling 'bootsound' > init: cannot find '/system/bin/playmp3', disabling 'bootsound' > sh: can't access tty; job control turned off > # <6>warning: `rild' uses 32-bit capabilities (legacy support in use) > warning: `rild' uses 32-bit capabilities (legacy support in use) > <6>request_suspend_state: wakeup (3->0) at 23607482910 (1970-01-01 > 00:00:23.607482910 UTC) > request_suspend_state: wakeup (3->0) at 23607482910 (1970-01-01 > 00:00:23.607482910 UTC) > <6>request_suspend_state: wakeup (0->0) at 24186004638 (1970-01-01 > 00:00:24.186004638 UTC) > request_suspend_state: wakeup (0->0) at 24186004638 (1970-01-01 > 00:00:24.186004638 UTC) > <6>request_suspend_state: wakeup (0->0) at 29410034179 (1970-01-01 > 00:00:29.410034179 UTC) > request_suspend_state: wakeup (0->0) at 29410034179 (1970-01-01 > 00:00:29.410034179 UTC) > <6>request_suspend_state: wakeup (0->0) at 35350250244 (1970-01-01 > 00:00:35.350219726 UTC) > request_suspend_state: wakeup (0->0) at 35350250244 (1970-01-01 > 00:00:35.350219726 UTC) > <6>request_suspend_state: wakeup (0->0) at 40411346435 (1970-01-01 > 00:00:40.411315917 UTC) > request_suspend_state: wakeup (0->0) at 40411346435 (1970-01-01 > 00:00:40.411315917 UTC) > <6>request_suspend_state: wakeup (0->0) at 45559783935 (1970-01-01 > 00:00:45.559783935 UTC) > request_suspend_state: wakeup (0->0) at 45559783935 (1970-01-01 > 00:00:45.559783935 UTC) > <6>request_suspend_state: wakeup (0->0) at 50434753417 (1970-01-01 > 00:00:50.434722900 UTC) > request_suspend_state: wakeup (0->0) at 50434753417 (1970-01-01 > 00:00:50.434722900 UTC) > What's the matter ande how to deal with it? > regards > Jennifer > > 在2009-04-01 00:14:13，"haritha uppalapati" <[email protected]> 写道： > > Hi > Follow the link below for creating RFS.Will work for OMAP3EVM. > http://labs.embinux.org/index.php/Android_Porting_Guide_to_Beagle_Board > regards > haritha > > 2009/3/30 jennifer <[email protected]> > >> >> I run the kernel with the follow information in the terminal： >> >> OMAP3EVM # bootm >> ## Booting image at 80000000 ... >> Image Name: Linux-2.6.27-omap1-05240-g88b76d >> Image Type: ARM Linux Kernel Image (uncompressed) >> Data Size: 1752600 Bytes = 1.7 MB >> Load Address: 80008000 >> Entry Point: 80008000 >> Verifying Checksum ... OK >> OK >> >> Starting kernel ... >> >> Uncompressing >> >> Linux................................................................................. >> ................................ done, booting the kernel. >> <5>Linux version 2.6.27-omap1-05240-g88b76df-dirty >> ([email protected]) (gcc version 4.2.1 ( >> CodeSourcery Sourcery G++ Lite 2007q3-51)) #2 Thu Mar 26 14:18:57 CST >> 2009 >> CPU: ARMv7 Processor [411fc082] revision 2 (ARMv7), cr=00c5387f >> Machine: OMAP3 EVM >> Memory policy: ECC disabled, Data cache writeback >> <7>On node 0 totalpages: 22528 >> <7>free_area_init_node: node 0, pgdat c0375e9c, node_mem_map c03f2000 >> <7> DMA zone: 22352 pages, LIFO batch:3 >> <6>OMAP3430 ES2.1 >> <6>SRAM: Mapped pa 0x40200000 to va 0xd7000000 size: 0x100000 >> CPU0: L1 I VIPT cache. Caches unified at level 2, coherent at level 3 >> CPU0: Level 1 cache is separate instruction and data >> CPU0: I cache: 16384 bytes, associativity 4, 64 byte lines, 64 sets, >> supports RA >> CPU0: D cache: 16384 bytes, associativity 4, 64 byte lines, 64 sets, >> supports RA WB WT >> CPU0: Level 2 cache is unified >> CPU0: unified cache: 262144 bytes, associativity 8, 64 byte lines, 512 >> sets, >> supports WA RA WB WT >> Built 1 zonelists in Zone order, mobility grouping on. Total pages: >> 22352 >> <5>Kernel command line: console=ttyS0,115200n8 rw root=/dev/nfs >> nfsroot=192.168.1.105:/home/jennifer >> /Android_rfs ip=dhcp nolock,rsize=1024,wsize=1024 rootdelay=2 >> video=omapfb:mode:640x...@50 init=/ini >> t mem=88M >> <3>clock: virt_vdd1_prcm_set: missing clockdomain<3>clock: >> virt_vdd2_prcm_set: missing clockdomain<6 >> >Clocking rate (Crystal/DPLL/ARM core): 26.0/332/500 MHz >> <6>GPMC revision 5.0 >> <6>IRQ: Found an INTC at 0xd8200000 (revision 4.0) with 96 interrupts >> <6>Total of 96 interrupts on 1 active controller >> <6>OMAP34xx GPIO hardware version 2.5 >> PID hash table entries: 512 (order: 9, 2048 bytes) >> <6>OMAP clockevent source: GPTIMER1 at 32768 Hz >> Console: colour dummy device 80x30 >> <6>Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) >> <6>Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) >> <6>Memory: 88MB = 88MB total >> <5>Memory: 85204KB available (3212K code, 642K data, 144K init) >> <6>Calibrating delay loop... 499.92 BogoMIPS (lpj=1949696) >> Mount-cache hash table entries: 512 >> <6>CPU: Testing write buffer coherency: ok >> <6>net_namespace: 288 bytes >> <6>NET: Registered protocol family 16 >> <4>MUX: setup J21_34XX_I2C1_SDA (0xd80021bc): 0x1718 -> 0x0118 >> <4>MUX: setup K21_34XX_I2C1_SCL (0xd80021ba): 0x1718 -> 0x0118 >> <4>MUX: setup AE15_34XX_I2C2_SDA (0xd80021c0): 0x1718 -> 0x0118 >> <4>MUX: setup AF15_34XX_I2C2_SCL (0xd80021be): 0x1718 -> 0x0118 >> <4>MUX: setup AG14_34XX_I2C3_SDA (0xd80021c4): 0x1718 -> 0x0118 >> <4>MUX: setup AF14_34XX_I2C3_SCL (0xd80021c2): 0x1718 -> 0x0118 >> <6>OneNAND: Unable to find configuration in GPMC >> <6>Switched to new clocking rate (Crystal/DPLL3/MPU): 26.0/332/166 >> MHz >> <6>OMAP DMA hardware revision 4.0 >> <3>USB: No board-specific platform config found >> <6>i2c_omap i2c_omap.1: bus 1 rev3.12 at 2600 kHz >> <6>twl4030: PIH (irq 7) chaining IRQs 368..375 >> <6>twl4030: power (irq 373) chaining IRQs 376..383 >> <6>twl4030: gpio (irq 368) chaining IRQs 384..401 >> <6>i2c_omap i2c_omap.2: bus 2 rev3.12 at 400 kHz >> <6>i2c_omap i2c_omap.3: bus 3 rev3.12 at 400 kHz >> <6>twl4030_usb twl4030_usb: Initialized TWL4030 USB module >> <5>SCSI subsystem initialized >> <6>usbcore: registered new interface driver usbfs >> <6>usbcore: registered new interface driver hub >> <6>usbcore: registered new device driver usb >> <6>musb_hdrc: version 6.0, musb-dma, otg (peripheral+host), debug=0 >> <7>musb_hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, bulk combine (X), >> bulk split (X), HB-ISO Rx (X), H >> B-ISO Tx (X), SoftConn) >> <7>musb_hdrc: MHDRC RTL version 1.400 >> <7>musb_hdrc: setup fifo_mode 4 >> <7>musb_hdrc: 29/31 max ep, 15424/16384 memory >> <7>musb_hdrc: hw_ep 0shared, max 64 >> <7>musb_hdrc: hw_ep 1tx, max 512 >> <7>musb_hdrc: hw_ep 1rx, max 512 >> <7>musb_hdrc: hw_ep 2tx, max 512 >> <7>musb_hdrc: hw_ep 2rx, max 512 >> <7>musb_hdrc: hw_ep 3tx, max 512 >> <7>musb_hdrc: hw_ep 3rx, max 512 >> <7>musb_hdrc: hw_ep 4tx, max 512 >> <7>musb_hdrc: hw_ep 4rx, max 512 >> <7>musb_hdrc: hw_ep 5tx, max 512 >> <7>musb_hdrc: hw_ep 5rx, max 512 >> <7>musb_hdrc: hw_ep 6tx, max 512 >> <7>musb_hdrc: hw_ep 6rx, max 512 >> <7>musb_hdrc: hw_ep 7tx, max 512 >> <7>musb_hdrc: hw_ep 7rx, max 512 >> <7>musb_hdrc: hw_ep 8tx, max 512 >> <7>musb_hdrc: hw_ep 8rx, max 512 >> <7>musb_hdrc: hw_ep 9tx, max 512 >> <7>musb_hdrc: hw_ep 9rx, max 512 >> <7>musb_hdrc: hw_ep 10tx, max 512 >> <7>musb_hdrc: hw_ep 10rx, max 512 >> <7>musb_hdrc: hw_ep 11tx, max 512 >> <7>musb_hdrc: hw_ep 11rx, max 512 >> <7>musb_hdrc: hw_ep 12tx, max 512 >> <7>musb_hdrc: hw_ep 12rx, max 512 >> <7>musb_hdrc: hw_ep 13tx, max 512 >> <7>musb_hdrc: hw_ep 13rx, max 512 >> <7>musb_hdrc: hw_ep 14shared, max 1024 >> <7>musb_hdrc: hw_ep 15shared, max 1024 >> <6>musb_hdrc: USB OTG mode controller at d80ab000 using DMA, IRQ 92 >> <6>NET: Registered protocol family 2 >> <7>Switched to high resolution mode on CPU 0 >> <6>IP route cache hash table entries: 1024 (order: 0, 4096 bytes) >> <6>TCP established hash table entries: 4096 (order: 3, 32768 bytes) >> <6>TCP bind hash table entries: 4096 (order: 2, 16384 bytes) >> <6>TCP: Hash tables configured (established 4096 bind 4096) >> <6>TCP reno registered >> <6>NET: Registered protocol family 1 >> <4>NetWinder Floating Point Emulator V0.97 (double precision) >> <6>ashmem: initialized >> <5>VFS: Disk quotas dquot_6.5.1 >> Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) >> <6>JFFS2 version 2.2. (NAND) 漏 2001-2006 Red Hat, Inc. >> <6>msgmni has been set to 166 >> <6>io scheduler noop registered >> <6>io scheduler anticipatory registered (default) >> <6>io scheduler deadline registered >> <6>io scheduler cfq registered >> <6>omapfb: configured for panel omap3evm >> <6>omapfb: DISPC version 3.0 initialized >> <6>omapfb: Framebuffer initialized. Total vram 1228800 planes 1 >> <6>omapfb: Pixclock 24000 kHz hfreq 45.7142 kHz vfreq 70.3 Hz >> <6>Serial: 8250/16550 driver4 ports, IRQ sharing enabled >> <6>serial8250.0: ttyS0 at MMIO 0x4806a000 (irq = 72) is a ST16654 >> <6>console [ttyS0] enabled >> Linux version 2.6.27-omap1-05240-g88b76df-dirty >> ([email protected]) (gcc version 4.2.1 (Cod >> eSourcery Sourcery G++ Lite 2007q3-51)) #2 Thu Mar 26 14:18:57 CST >> 2009 >> CPU: ARMv7 Processor [411fc082] revision 2 (ARMv7), cr=00c5387f >> Machine: OMAP3 EVM >> Memory policy: ECC disabled, Data cache writeback >> OMAP3430 ES2.1 >> SRAM: Mapped pa 0x40200000 to va 0xd7000000 size: 0x100000 >> CPU0: L1 I VIPT cache. Caches unified at level 2, coherent at level 3 >> CPU0: Level 1 cache is separate instruction and data >> CPU0: I cache: 16384 bytes, associativity 4, 64 byte lines, 64 sets, >> supports RA >> CPU0: D cache: 16384 bytes, associativity 4, 64 byte lines, 64 sets, >> supports RA WB WT >> CPU0: Level 2 cache is unified >> CPU0: unified cache: 262144 bytes, associativity 8, 64 byte lines, 512 >> sets, >> supports WA RA WB WT >> Built 1 zonelists in Zone order, mobility grouping on. Total pages: >> 22352 >> Kernel command line: console=ttyS0,115200n8 rw root=/dev/nfs >> nfsroot=192.168.1.105:/home/jennifer/An >> droid_rfs ip=dhcp nolock,rsize=1024,wsize=1024 rootdelay=2 >> video=omapfb:mode:640x...@50 init=/init m >> em=88M >> clock: virt_vdd1_prcm_set: missing clockdomain<3>clock: >> virt_vdd2_prcm_set: missing clockdomain<6>Cl >> ocking rate (Crystal/DPLL/ARM core): 26.0/332/500 MHz >> GPMC revision 5.0 >> IRQ: Found an INTC at 0xd8200000 (revision 4.0) with 96 interrupts >> Total of 96 interrupts on 1 active controller >> OMAP34xx GPIO hardware version 2.5 >> PID hash table entries: 512 (order: 9, 2048 bytes) >> OMAP clockevent source: GPTIMER1 at 32768 Hz >> Console: colour dummy device 80x30 >> Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) >> Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) >> Memory: 88MB = 88MB total >> Memory: 85204KB available (3212K code, 642K data, 144K init) >> Calibrating delay loop... 499.92 BogoMIPS (lpj=1949696) >> Mount-cache hash table entries: 512 >> CPU: Testing write buffer coherency: ok >> net_namespace: 288 bytes >> NET: Registered protocol family 16 >> MUX: setup J21_34XX_I2C1_SDA (0xd80021bc): 0x1718 -> 0x0118 >> MUX: setup K21_34XX_I2C1_SCL (0xd80021ba): 0x1718 -> 0x0118 >> MUX: setup AE15_34XX_I2C2_SDA (0xd80021c0): 0x1718 -> 0x0118 >> MUX: setup AF15_34XX_I2C2_SCL (0xd80021be): 0x1718 -> 0x0118 >> MUX: setup AG14_34XX_I2C3_SDA (0xd80021c4): 0x1718 -> 0x0118 >> MUX: setup AF14_34XX_I2C3_SCL (0xd80021c2): 0x1718 -> 0x0118 >> OneNAND: Unable to find configuration in GPMC >> <6>Switched to new clocking rate (Crystal/DPLL3/MPU): 26.0/332/166 >> MHz >> OMAP DMA hardware revision 4.0 >> USB: No board-specific platform config found >> i2c_omap i2c_omap.1: bus 1 rev3.12 at 2600 kHz >> twl4030: PIH (irq 7) chaining IRQs 368..375 >> twl4030: power (irq 373) chaining IRQs 376..383 >> twl4030: gpio (irq 368) chaining IRQs 384..401 >> i2c_omap i2c_omap.2: bus 2 rev3.12 at 400 kHz >> i2c_omap i2c_omap.3: bus 3 rev3.12 at 400 kHz >> twl4030_usb twl4030_usb: Initialized TWL4030 USB module >> SCSI subsystem initialized >> usbcore: registered new interface driver usbfs >> usbcore: registered new interface driver hub >> usbcore: registered new device driver usb >> musb_hdrc: version 6.0, musb-dma, otg (peripheral+host), debug=0 >> musb_hdrc: USB OTG mode controller at d80ab000 using DMA, IRQ 92 >> NET: Registered protocol family 2 >> IP route cache hash table entries: 1024 (order: 0, 4096 bytes) >> TCP established hash table entries: 4096 (order: 3, 32768 bytes) >> TCP bind hash table entries: 4096 (order: 2, 16384 bytes) >> TCP: Hash tables configured (established 4096 bind 4096) >> TCP reno registered >> NET: Registered protocol family 1 >> NetWinder Floating Point Emulator V0.97 (double precision) >> ashmem: initialized >> VFS: Disk quotas dquot_6.5.1 >> Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) >> JFFS2 version 2.2. (NAND) 漏 2001-2006 Red Hat, Inc. >> msgmni has been set to 166 >> io scheduler noop registered >> io scheduler anticipatory registered (default) >> io scheduler deadline registered >> io scheduler cfq registered >> omapfb: configured for panel omap3evm >> omapfb: DISPC version 3.0 initialized >> omapfb: Framebuffer initialized. Total vram 1228800 planes 1 >> omapfb: Pixclock 24000 kHz hfreq 45.7142 kHz vfreq 70.3 Hz >> Serial: 8250/16550 driver4 ports, IRQ sharing enabled >> serial8250.0: ttyS0 at MMIO 0x4806a000 (irq = 72) is a ST16654 >> console [ttyS0] enabled >> <6>serial8250.0: ttyS1 at MMIO 0x4806c000 (irq = 73) is a ST16654 >> serial8250.0: ttyS1 at MMIO 0x4806c000 (irq = 73) is a ST16654 >> <6>serial8250.0: ttyS2 at MMIO 0x49020000 (irq = 74) is a ST16654 >> serial8250.0: ttyS2 at MMIO 0x49020000 (irq = 74) is a ST16654 >> <6>brd: module loaded >> brd: module loaded >> <6>loop: module loaded >> loop: module loaded >> <6>logger: created 64K log 'log_main' >> logger: created 64K log 'log_main' >> <6>logger: created 256K log 'log_events' >> logger: created 256K log 'log_events' >> <6>logger: created 64K log 'log_radio' >> logger: created 64K log 'log_radio' >> eth0: LAN9115 (rev 2) at 0x2c000000 IRQ 336eth0: LAN9115 (rev 2) at >> 0x2c000000 IRQ 336 >> >> eth0: Ethernet addr: eth0: Ethernet addr: 00:00:50:50:c2:c2:7e:7e:8a: >> 8a:bc >> bc >> <7>eth0: LAN911x Internal PHY >> <6>i2c /dev entries driver >> i2c /dev entries driver >> <4>Driver 'sd' needs updating - please use bus_type methods >> Driver 'sd' needs updating - please use bus_type methods >> <6>OneNAND driver initializing >> OneNAND driver initializing >> <5>usbmon: debugfs is not available >> usbmon: debugfs is not available >> <6>Initializing USB Mass Storage driver... >> Initializing USB Mass Storage driver... >> <6>usbcore: registered new interface driver usb-storage >> usbcore: registered new interface driver usb-storage >> <6>USB Mass Storage support registered. >> USB Mass Storage support registered. >> <6>usbcore: registered new interface driver usbtest >> usbcore: registered new interface driver usbtest >> <6>input: omap_twl4030keypad as /class/input/input0 >> input: omap_twl4030keypad as /class/input/input0 >> <6>ads7846 spi1.0: touchscreen, irq 335 >> ads7846 spi1.0: touchscreen, irq 335 >> <6>input: ADS784x Touchscreen as /class/input/input1 >> input: ADS784x Touchscreen as /class/input/input1 >> <6>OMAP Watchdog Timer Rev 0x31: initial timeout 60 sec >> OMAP Watchdog Timer Rev 0x31: initial timeout 60 sec >> <6>usbcore: registered new interface driver usbhid >> usbcore: registered new interface driver usbhid >> <6>usbhid: v2.6:USB HID core driver >> usbhid: v2.6:USB HID core driver >> <6>TCP cubic registered >> TCP cubic registered >> <6>NET: Registered protocol family 17 >> NET: Registered protocol family 17 >> <6>NET: Registered protocol family 15 >> NET: Registered protocol family 15 >> <6>RPC: Registered udp transport module. >> RPC: Registered udp transport module. >> <6>RPC: Registered tcp transport module. >> RPC: Registered tcp transport module. >> <3>Power Management for TI OMAP3. >> Power Management for TI OMAP3. >> <6>SmartReflex driver initialized >> SmartReflex driver initialized >> <6>Disabling unused clock "gpt2_ick" >> Disabling unused clock "gpt2_ick" >> <6>Disabling unused clock "gpio2_dbck" >> Disabling unused clock "gpio2_dbck" >> <6>Disabling unused clock "gpio3_dbck" >> Disabling unused clock "gpio3_dbck" >> <6>Disabling unused clock "gpio4_dbck" >> Disabling unused clock "gpio4_dbck" >> <6>Disabling unused clock "gpio5_dbck" >> Disabling unused clock "gpio5_dbck" >> <6>Disabling unused clock "gpt2_fck" >> Disabling unused clock "gpt2_fck" >> <6>Disabling unused clock "wdt2_ick" >> Disabling unused clock "wdt2_ick" >> <6>Disabling unused clock "wdt2_fck" >> Disabling unused clock "wdt2_fck" >> <6>Disabling unused clock "dpll5_ck" >> Disabling unused clock "dpll5_ck" >> <6>Disabling unused clock "dpll4_m6x2_ck" >> Disabling unused clock "dpll4_m6x2_ck" >> <6>Disabling unused clock "dpll4_m5x2_ck" >> Disabling unused clock "dpll4_m5x2_ck" >> <6>Disabling unused clock "dpll3_m3x2_ck" >> Disabling unused clock "dpll3_m3x2_ck" >> <6>Disabling unused clock "sys_clkout1" >> Disabling unused clock "sys_clkout1" >> <6>VFP support v0.3: VFP support v0.3: implementor 41 architecture 3 >> part 30 variant c rev 1 >> implementor 41 architecture 3 part 30 variant c rev 1 >> drivers/rtc/hctosys.c: unable to open rtc device (rtc0) >> drivers/rtc/hctosys.c: unable to open rtc device (rtc0) >> <6>eth0: link down >> eth0: link down >> <5>Sending DHCP requests .Sending DHCP requests .<6>eth0: link up, >> 100Mbps, full-duplex, lpa 0x05E1 >> <6>eth0: link up, 100Mbps, full-duplex, lpa 0x05E1 >> ..,, OK >> OK >> IP-Config: Got DHCP answer from 0.0.0.0, IP-Config: Got DHCP answer >> from 0.0.0.0, my address is 192. >> 168.1.104 >> my address is 192.168.1.104 >> IP-Config: Complete:IP-Config: Complete: >> device=eth0 >> device=eth0, addr=192.168.1.104, addr=192.168.1.104, >> mask=255.255.255.0, mask=255.255.255.0, gw >> =192.168.1.1, gw=192.168.1.1, >> host=192.168.1.104, domain=domain, nis-domain=(none), >> host=192.168.1.104, domain=domain, nis-domain=(none), >> bootserver=0.0.0.0, >> bootserver=0.0.0.0, rootserver=192.168.1.105, >> rootserver=192.168.1.105, rootpath=, rootpath= >> >> <6>Waiting 2sec before mounting root device... >> Waiting 2sec before mounting root device... >> <5>Looking up port of RPC 100003/2 on 192.168.1.105 >> Looking up port of RPC 100003/2 on 192.168.1.105 >> <5>Looking up port of RPC 100005/1 on 192.168.1.105 >> Looking up port of RPC 100005/1 on 192.168.1.105 >> VFS: Mounted root (nfs filesystem). >> VFS: Mounted root (nfs filesystem). >> <6>Freeing init memory: 144K >> Freeing init memory: 144K >> <4>Warning: unable to open an initial console. >> Warning: unable to open an initial console. >> <3>init: cannot open '/initlogo.rle' >> init: cannot open '/initlogo.rle' >> <3>init: Unable to open persistent property directory /data/property >> errno: 2 >> init: Unable to open persistent property directory /data/property >> errno: 2 >> <3>init: cannot find '/system/bin/playmp3', disabling 'bootsound' >> init: cannot find '/system/bin/playmp3', disabling 'bootsound' >> sh: can't access tty; job control turned off >> # <6>warning: `rild' uses 32-bit capabilities (legacy support in use) >> warning: `rild' uses 32-bit capabilities (legacy support in use) >> <6>request_suspend_state: wakeup (3->0) at 23607482910 (1970-01-01 >> 00:00:23.607482910 UTC) >> request_suspend_state: wakeup (3->0) at 23607482910 (1970-01-01 >> 00:00:23.607482910 UTC) >> <6>request_suspend_state: wakeup (0->0) at 24186004638 (1970-01-01 >> 00:00:24.186004638 UTC) >> request_suspend_state: wakeup (0->0) at 24186004638 (1970-01-01 >> 00:00:24.186004638 UTC) >> <6>request_suspend_state: wakeup (0->0) at 29410034179 (1970-01-01 >> 00:00:29.410034179 UTC) >> request_suspend_state: wakeup (0->0) at 29410034179 (1970-01-01 >> 00:00:29.410034179 UTC) >> <6>request_suspend_state: wakeup (0->0) at 35350250244 (1970-01-01 >> 00:00:35.350219726 UTC) >> request_suspend_state: wakeup (0->0) at 35350250244 (1970-01-01 >> 00:00:35.350219726 UTC) >> <6>request_suspend_state: wakeup (0->0) at 40411346435 (1970-01-01 >> 00:00:40.411315917 UTC) >> request_suspend_state: wakeup (0->0) at 40411346435 (1970-01-01 >> 00:00:40.411315917 UTC) >> <6>request_suspend_state: wakeup (0->0) at 45559783935 (1970-01-01 >> 00:00:45.559783935 UTC) >> request_suspend_state: wakeup (0->0) at 45559783935 (1970-01-01 >> 00:00:45.559783935 UTC) >> <6>request_suspend_state: wakeup (0->0) at 50434753417 (1970-01-01 >> 00:00:50.434722900 UTC) >> request_suspend_state: wakeup (0->0) at 50434753417 (1970-01-01 >> 00:00:50.434722900 UTC) >> >> >> >> Now I don't know how to make the root filesystem for the evm with >> android .Please give me some detailed steps. >> Thanks! >> >> > > 网易邮箱，中国第一大电子邮件服务商 <http://email.163.com>> > --~--~---------~--~----~------------~-------~--~----~ unsubscribe: [email protected] website: http://groups.google.com/group/android-porting -~----------~----~----~----~------~----~------~--~---
