I have a problem with Wifi that it's not showing any scan results in the GUI. Anyone patched that problem already? I think it's the parseresults function.
On 10 apr, 07:49, nail <[email protected]> wrote: > Dear Roman > > yes, i got IP and can connect to network, > > it is because i have configred the wpa_supplicant.conf, and the > contents is shown below: > > wpa_supplicant.conf: > =============================================================== > update_config=1 > eapol_version=1 > ap_scan=1 # ap_scan=1: wpa_supplicant initiates scanning and AP > selection > fast_reauth=1 > > network={ > ssid="simple" > psk="very secret passphrase" > priority=5 > > } > > # Wildcard match for SSID (plaintext APs only). This example selects > any > # open AP regardless of its SSID. > network={ > key_mgmt=NONE > > } > > =============================================================== > > so, it will do all things needed automatically, > > could you please help me to find out where to get the SSID ? > > On 4月10日, 上午11時23分, Roman Baumgaertner <roman.baumgaert...@t- > > mobile.com> wrote: > > Hi Nail, > > > You mentioned that you are connected. What does it mean you are connected? > > Did you get an IP address or are you attached to the AP (you should be able > > to see the SSID)? > > > Try first to find out on the AP whether it can see you. > > > Roman Baumgaertner > > > Sr. SW Engineer-OSDC > > ・T・ ・ ・Mobile・ stick together > > The views, opinions and statements in this email are those of the > > author solely in their individual capacity, and do not necessarily > > represent those of T-Mobile USA, Inc. > > > On 4/9/09 7:19 PM, "nail" <[email protected]> wrote: > > > > Hi, I have enabledwifiusing the following command written in > > > init.rc: > > > > "mkdir /data/misc/wifi0770wifiwifi > > > mkdir /data/misc/wifi/sockets 0770wifiwifi > > > mkdir /data/system/wpa_supplicant 0770wifiwifi > > > mkdir /data/misc/dhcp 0770 dhcp dhcp > > > chown dhcp dhcp /data/misc/dhcp > > > > ifup wlan0 > > > > service wpa_supplicant /system/bin/logwrapper /system/bin/ > > > wpa_supplicant -iwlan0 -c/system/etc/wifi/wpa_supplicant.conf -dd > > > groupwifi > > > > service wlan_dhcpcd /system/bin/dhcpcd wlan0 " > > > > and it can connetc to the network, but when i type "wpa_cli -p/data/ > > > system/wpa_supplicant/ scan" > > > > it shows "Failed to connect to wpa_supplicant - wpa_ctrl_open: Unknown > > > error: 0" > > > > do you have any idea about this ? thank you > > > > On 3月27日, 下午7時49分, Androidphan <[email protected]> wrote: > > >> # wpa_cli -p/data/system/wpa_supplicant/ scan > > >> Selected interface 'wlan0' > > >> Failed to connect to wpa_supplicant - wpa_ctrl_open: No such file or > > >> directory > > > >> On 27 mrt, 12:15, Michael Trimarchi <[email protected]> > > >> wrote: > > > >>> Hi, > > > >>> Androidphan wrote: > > >>>> This is the output when starting wpa_supplicant: > > > >>>> Initializing interface 'wlan0' conf '/system/etc/wifi/ > > >>>> wpa_supplicant.conf' > > >>>> drive > > >>>> r 'wext' ctrl_interface 'N/A' bridge 'N/A' > > >>>> Configuration file '/system/etc/wifi/wpa_supplicant.conf' -> '/system/ > > >>>> etc/wifi/ > > >>>> w > > >>>> pa_supplicant.conf' > > >>>> Reading configuration file '/system/etc/wifi/wpa_supplicant.conf' > > >>>> update_config=1 > > >>>> ctrl_interface='DIR=/data/system/wpa_supplicant/ GROUP=system' > > >>>> eapol_version=1 > > >>>> ap_scan=1 > > >>>> fast_reauth=1 > > >>>> Initializing interface (2) 'wlan0' > > >>>> EAPOL: SUPP_PAE entering state DISCONNECTED > > >>>> EAPOL: KEY_RX entering state NO_KEY_RECEIVE > > >>>> EAPOL: SUPP_BE entering state INITIALIZE > > >>>> EAP: EAP entering state DISABLED > > >>>> EAPOL: External notification - portEnabled=0 > > >>>> EAPOL: External notification - portValid=0 > > >>>> SIOCGIWRANGE: WE(compiled)=22 WE(source)=21 enc_capa=0xf > > >>>> capabilities: key_mgmt 0xf enc 0xf > > >>>> WEXT: Operstate: linkmode=1, operstate=5 > > >>>> Own MAC address: 00:22:43:2c:fa:a6 > > >>>> wpa_driver_wext_set_wpa > > >>>> wpa_driver_wext_set_key: alg=0 key_idx=0 set_tx=0 seq_len=0 key_len=0 > > >>>> wpa_driver_wext_set_key: alg=0 key_idx=1 set_tx=0 seq_len=0 key_len=0 > > >>>> wpa_driver_wext_set_key: alg=0 key_idx=2 set_tx=0 seq_len=0 key_len=0 > > >>>> wpa_driver_wext_set_key: alg=0 key_idx=3 set_tx=0 seq_len=0 key_len=0 > > >>>> wpa_driver_wext_set_countermeasures > > >>>> ioctl[SIOCSIWAUTH]: Operation not supported on transport endpoint > > >>>> WEXT auth param 4 value 0x0 - wpa_driver_wext_set_drop_unencrypted > > >>>> Setting scan request: 0 sec 100000 usec > > >>>> ctrl_interface_group=1000 (from group name 'system') > > >>>> Added interface wlan0 > > >>>> RTM_NEWLINK: operstate=0 ifi_flags=0x1002 () > > >>>> RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added > > >>>> Wireless event: cmd=0x8b06 len=8 > > >>>> Ignore event for foreign ifindex 4 > > >>>> RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP]) > > >>>> RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added > > >>>> State: DISCONNECTED -> SCANNING > > >>>> CTRL-EVENT-STATE-CHANGE id=-1 state=2 > > >>>> Starting AP scan (broadcast SSID) > > >>>> Trying to get current scan results first without requesting a new scan > > >>>> to > > >>>> speed > > >>>> up initial association > > >>>> Received 0 bytes of scan results (0 BSSes) > > >>>> Scan results: 0 > > >>>> CTRL-EVENT-SCAN-RESULTS Ready > > > >>> Hi, test youwificonnection using the wpa_cli program. The parse > > >>> function of the > > >>> scan result expect a - to the signal stregh (if I remember) to parse the > > >>> result, otherwise > > >>> fail. > > > >>> wpa_cli has an interractive mode to operate, and you can send command > > >>> like: > > >>> scan and scan-results. > > > >>>> No suitable AP found. > > >>>> Setting scan request: 0 sec 0 usec > > >>>> No enabled networks - do not scan > > >>>> State: SCANNING -> INACTIVE > > >>>> CTRL-EVENT-STATE-CHANGE id=-1 state=1 > > > >>>> On 27 mrt, 11:39, Androidphan <[email protected]> wrote: > > > >>>>> I'm getting the following error at the moment: > > >>>>> D/WifiHW ( 2325): Unable to open connection to supplicant on "/data/ > > >>>>> system/wpa_supplicant/wlan0": No such file or directory > > > >>>>> I got wpa_supplicant running. > > > >>>>> # ls -l /data/system/wpa_supplicant/ > > >>>>> srwxrwx--- root system 2009-03-27 11:39 wlan0 > > > >>>>> So it exists. > > > >>>>> Why is this?? > > > >>> Regards Michael- 隱藏被引用文字 - > > > >> - 顯示被引用文字 - > > > Roman Baumgaertner > > > Sr. SW Engineer-OSDC > > ・T・ ・ ・Mobile・ stick together > > The views, opinions and statements in this email are those of the > > author solely in their individual capacity, and do not necessarily > > represent those of T-Mobile USA, Inc.- 隱藏被引用文字 - > > > - 顯示被引用文字 - --~--~---------~--~----~------------~-------~--~----~ unsubscribe: [email protected] website: http://groups.google.com/group/android-porting -~----------~----~----~----~------~----~------~--~---
