Hi All, I have flashed the image using SD card and booted my OMAP3530 EVM (mistral board). I followed the document they have given me..
while booting .. from SD/MMC card... I am getting these msg.. X-loader 1.41(OMAP3EVM-1.1) (Apr 8 2009 - 16:29:36) Detected Samsung MuxOneNAND1G Flash Starting X-loader on MMC Reading boot sector 196968 Bytes Read from MMC Starting OS Bootloader from MMC... Starting OS Bootloader... Unknown Boot chip!!! U-Boot 1.1.6(OMAP3EVM-1.1) (Apr 8 2009 - 16:34:49) Mistral OMAP3EVM Development Board DRAM: 128 MB OneNAND Manufacturer: Samsung (0xec) Muxed OneNAND 128MB 1.8V 16-bit (0x30) OneNAND version = 0x0221 Scanning device for bad blocks num of blocks = 2048 onenand_wait: controller error = 0x2400 Bad factory block738 at 0x05c40000 Using default environment In: serial Out: serial Err: serial Reseting CHIP... Done LAN9x18 (0x01150002) detected. Setting mac address: aa:bb:cc:dd:ee:ff start Auto negotiation... (take ~2sec) Auto negotiation failed The board has OneNand flash. Using OneNand based commands Hit any key to stop autoboot: 0 1951744 bytes read ## Booting image at 80000000 ... Image Name: Linux-2.6.28-OMAP3EVM-1.1-00026- Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 1951680 Bytes = 1.9 MB Load Address: 80008000 Entry Point: 80008000 Verifying Checksum ... OK OK Starting kernel ... Uncompressing Linux...................................................................................................................................... do. Linux version 2.6.28-OMAP3EVM-1.1-00026-g461463c ([email protected]) (gcc version 4.2.1 (CodeSourcery Sourcery G++ Lite 2007q3-51)) #1 Thu Apr 99 CPU: ARMv7 Processor [411fc082] revision 2 (ARMv7), cr=10c5387f CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache Machine: OMAP3 EVM Memory policy: ECC disabled, Data cache writeback OMAP3430 ES2.1 SRAM: Mapped pa 0x40200000 to va 0xd7000000 size: 0x100000 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512 Kernel command line: mem=128M console=ttyS0,115200n8 root=/dev/ mmcblk0p2 rw rootdelay=2 Clocking rate (Crystal/DPLL/ARM core): 26.0/332/500 MHz GPMC revision 5.0 IRQ: Found an INTC at 0xd8200000 (revision 4.0) with 96 interrupts Total of 96 interrupts on 1 active controller OMAP34xx GPIO hardware version 2.5 PID hash table entries: 512 (order: 9, 2048 bytes) OMAP clockevent source: GPTIMER1 at 32768 Hz Console: colour dummy device 80x30 Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) Memory: 128MB = 128MB total Memory: 125084KB available (3556K code, 673K data, 440K init) Calibrating delay loop... 499.92 BogoMIPS (lpj=1949696) Mount-cache hash table entries: 512 CPU: Testing write buffer coherency: ok net_namespace: 288 bytes NET: Registered protocol family 16 OMAP DMA hardware revision 4.0 USB: No board-specific platform config found i2c_omap i2c_omap.1: bus 1 rev3.12 at 2600 kHz twl4030: PIH (irq 7) chaining IRQs 368..375 twl4030: power (irq 373) chaining IRQs 376..383 i2c_omap i2c_omap.2: bus 2 rev3.12 at 400 kHz i2c_omap i2c_omap.3: bus 3 rev3.12 at 400 kHz SCSI subsystem initialized twl4030_usb twl4030_usb: Initialized TWL4030 USB module usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb musb_hdrc: version 6.0, musb-dma, otg (peripheral+host), debug=0 musb_hdrc: USB OTG mode controller at d80ab000 using DMA, IRQ 92 NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 4096 (order: 3, 32768 bytes) TCP bind hash table entries: 4096 (order: 2, 16384 bytes) TCP: Hash tables configured (established 4096 bind 4096) TCP reno registered NET: Registered protocol family 1 NetWinder Floating Point Emulator V0.97 (double precision) ashmem: initialized VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) JFFS2 version 2.2. (NAND) .. 2001-2006 Red Hat, Inc. yaffs Apr 9 2009 11:03:21 Installing. msgmni has been set to 244 alg: No test for stdrng (krng) io scheduler noop registered io scheduler anticipatory registered (default) io scheduler deadline registered io scheduler cfq registered This is backlight driver Allocating static major number 255 to omap3evm_bl driver omapfb: configured for panel omap3evm omapfb: DISPC version 3.0 initialized Console: switching to colour frame buffer device 60x40 omapfb: Framebuffer initialized. Total vram 1228800 planes 1 omapfb: Pixclock 19636 kHz hfreq 37.9 kHz vfreq 57.5 Hz Serial: 8250/16550 driver4 ports, IRQ sharing enabled serial8250.0: ttyS0 at MMIO 0x4806a000 (irq = 72) is a ST16654 console [ttyS0] enabled serial8250.0: ttyS1 at MMIO 0x4806c000 (irq = 73) is a ST16654 serial8250.0: ttyS2 at MMIO 0x49020000 (irq = 74) is a ST16654 brd: module loaded loop: module loaded eth0: LAN9115 (rev 2) at 0x2c000000 IRQ 336 eth0: Ethernet addr: aa:bb:cc:dd:ee:ff i2c /dev entries driver input: triton2-pwrbutton as /class/input/input0 triton2 power button driver initialized Driver 'sd' needs updating - please use bus_type methods omap2-nand driver initializing OneNAND driver initializing omap2-onenand omap2-onenand: initializing on CS0, phys base 0x20000000, virtual base c8880000 Muxed OneNAND 128MB 1.8V 16-bit (0x30) OneNAND version = 0x0221 Scanning device for bad blocks onenand_bbt_wait: ecc error = 0x2222, controller error 0x2400 Bad eraseblock 738 at 0x05c40000 Creating 9 MTD partitions on "omap2-onenand": 0x00000000-0x00020000 : "X-Loader(1)" 0x00020000-0x00040000 : "X-Loader(2)" 0x00040000-0x00060000 : "X-Loader(3)" 0x00060000-0x00080000 : "X-Loader(4)" 0x00080000-0x00100000 : "U-Boot" 0x00100000-0x00120000 : "U-Boot Environment" 0x00120000-0x00520000 : "Kernel(1)" 0x00520000-0x00920000 : "Kernel(2)" 0x00920000-0x08000000 : "File System" android adb driver musb_hdrc musb_hdrc: MUSB HDRC host driver musb_hdrc musb_hdrc: new USB bus registered, assigned bus number 1 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb1: Product: MUSB HDRC host driver usb usb1: Manufacturer: Linux 2.6.28-OMAP3EVM-1.1-00026-g461463c musb- hcd usb usb1: SerialNumber: musb_hdrc input: omap_twl4030keypad as /class/input/input1 [ads7846_probe]: pressure_min=0, pressure_max=255 ads7846 spi1.0: touchscreen, irq 335 input: ADS784x Touchscreen as /class/input/input2 twl4030_rtc twl4030_rtc: rtc core: registered twl4030_rtc as rtc0 twl4030_rtc twl4030_rtc: Power up reset detected. twl4030_rtc twl4030_rtc: Enabling TWL4030-RTC. mmci-omap-hs mmci-omap-hs.0: Failed to get debounce clock usbcore: registered new interface driver usbhid usbhid: v2.6:USB HID core driver logger: created 64K log 'log_main' logger: created 256K log 'log_events' logger: created 64K log 'log_radio' Advanced Linux Sound Architecture Driver Version 1.0.18rc3. ASoC version 0.13.2 OMAP3EVM SoC init TWL4030 Audio Codec init asoc: twl4030 <-> omap-mcbsp-dai-(link_id) mapping ok ALSA device list: #0: OMAP3EVM (twl4030) TCP cubic registered NET: Registered protocol family 17 NET: Registered protocol family 15 RPC: Registered udp transport module. RPC: Registered tcp transport module. ieee80211: 802.11 data/management/control stack, git-1.1.13 ieee80211: Copyright (C) 2004-2005 Intel Corporation <[email protected]> Power Management for TI OMAP3. VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 1 twl4030_rtc twl4030_rtc: setting system clock to 2000-01-01 00:00:00 UTC (946684800) Waiting 2sec before mounting root device... mmc0: host does not support reading read-only switch. assuming write- enable. mmc0: new high speed SD card at address 0002 mmcblk0: mmc0:0002 00000 1.90 GiB mmcblk0: p1 p2 kjournald starting. Commit interval 5 seconds EXT3 FS on mmcblk0p2, internal journal EXT3-fs: recovery complete. EXT3-fs: mounted filesystem with ordered data mode. VFS: Mounted root (ext3 filesystem). Freeing init memory: 440K init started: BusyBox v1.8.1 (2007-11-14 09:47:41 EST) starting pid 435, tty '': '/startme' Disabling Power mgmt : /startme: cannot create /sys/power/ cpuidle_deepest_state: directory nonexistent Turn off LCD after 1 hour : /startme: cannot create /sys/power/ fb_timeout_value: directory nonexistent Socket created. Bind completed! [Thread]: cmd_processor_name=COMMON_TASKS_SLOW [deQueueCmdPkt]: COMMON_TASKS_SLOW waiting ... [Thread]: cmd_processor_name=COMMON_TASKS_FAST [deQueueCmdPkt]: COMMON_TASKS_FAST waiting ... [Thread]: cmd_processor_name=AUDIO_CTRL_TASKS [setMasterVolume]: cmd_buf=/usr/bin/amixer cset numid=2 70 sh: /usr/bin/amixer: not found [Thread]: cmd_processor_name=AUDIO_PB_REC_TASKS [deQueueCmdPkt]: AUDIO_PB_REC_TASKS waiting ... [deQueueCmdPkt]: AUDIO_CTRL_TASKS waiting ... Initializing Android... This process may take atlease 2-3 minutes to bring up the home page, please wait....... init: cannot open '/initlogo.rle' sh: can't access tty; job control turned off # warning: `app_process' uses 32-bit capabilities (legacy support in use) android_power: wakeup (0->0) at 32725341832 (2000-01-01 00:00:31.648620593 UTC) eth0: link down binder: release 831:831 transaction 503 out, still active binder: 772:836 transaction failed 29189, size 4-0 binder: send failed reply for transaction 503, target dead Job control is turned off.. :( Can someone please guide me.. how to proceed... Can you please suggest me.. how can i a test a test application .. please suggest some tools and any links.. We are using Fedora core 6. Do I need to migrate to Ubuntu ? I am new to android... Thanks in advance.. Mahalakshmi. --~--~---------~--~----~------------~-------~--~----~ unsubscribe: [email protected] website: http://groups.google.com/group/android-porting -~----------~----~----~----~------~----~------~--~---
