////////////////////////////// ////////////////////////////// ////////////////////////// The following is the debug log : OMAP3 beagleboard.org # setenv bootargs console=ttyS2,115200n8 noinitrd root=/dev/mmcblk0p2 video=omapfb.mode=dvi:1280x720mr...@50 init=/init rootfstype=ext3 rw rootdelay=1 nohz=off androidboot.console=ttyS2 OMAP3 beagleboard.org # mmcinit OMAP3 beagleboard.org # fatload mmc 0 0x80300000 uImage.bin reading uImage.bin 2044236 bytes read OMAP3 beagleboard.org # bootm 0x80300000 ////////////////////////////////////////////////////////////////////////////////////// I typed above. ## Booting kernel from Legacy Image at 80300000 ... Image Name: Linux-2.6.29-omap1-07255-g85f054 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2044172 Bytes = 1.9 MB Load Address: 80008000 Entry Point: 80008000 Verifying Checksum ... OK Loading Kernel Image ... OK OK Starting kernel ... Uncompressing Linux...................................................................................................................................... done, booting the kernel. Linux version 2.6.29-omap1-07255-g85f0546 (lzm73...@michael-ubuntu) (gcc version 4.2.3 (Sourcery G++ Lite 2008q1-126)) #1 Thu Dec 17 09:46:05 CST 2009 CPU: ARMv7 Processor [411fc083] revision 3 (ARMv7), cr=10c5387f CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache Machine: OMAP3 Beagle Board Memory policy: ECC disabled, Data cache writeback OMAP3430 ES3.1 SRAM: Mapped pa 0x40200000 to va 0xd7000000 size: 0x100000 Reserving 12582912 bytes SDRAM for VRAM Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024 Kernel command line: console=ttyS2,115200n8 noinitrd root=/dev/ mmcblk0p2 video=omapfb.mode=dvi:1280x720mr...@50 init=/init rootfstype=ext3 rw rootdelay=1 nohz=off androidboot.console=ttyS2 Unknown boot option `androidboot.console=ttyS2': ignoring Clocking rate (Crystal/DPLL/ARM core): 26.0/332/500 MHz GPMC revision 5.0 IRQ: Found an INTC at 0xd8200000 (revision 4.0) with 96 interrupts Total of 96 interrupts on 1 active controller OMAP34xx GPIO hardware version 2.5 PID hash table entries: 1024 (order: 10, 4096 bytes) OMAP clockevent source: GPTIMER12 at 32768 Hz Console: colour dummy device 80x30 Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) Memory: 128MB 128MB = 256MB total Memory: 242688KB available (3820K code, 718K data, 144K init) Calibrating delay loop... 472.66 BogoMIPS (lpj=1847296) Mount-cache hash table entries: 512 CPU: Testing write buffer coherency: ok net_namespace: 520 bytes regulator: core version 0.5 NET: Registered protocol family 16 Found NAND on CS0 Registering NAND on CS0 OMAP DMA hardware revision 4.0 bio: create slab <bio-0> at 0 OMAP DSS rev 2.0 OMAP DISPC rev 3.0 OMAP VENC rev 2 i2c_omap i2c_omap.1: bus 1 rev3.12 at 2600 kHz twl4030: PIH (irq 7) chaining IRQs 368..375 twl4030: power (irq 373) chaining IRQs 376..383 twl4030: gpio (irq 368) chaining IRQs 384..401 regulator: VMMC1: 1850 <--> 3150 mV normal standby regulator: VDAC: 1800 mV normal standby regulator: VUSB1V5: 1500 <--> 0 mV normal standby regulator: VUSB1V8: 1800 <--> 0 mV normal standby regulator: VUSB3V1: 3100 <--> 0 mV normal standby regulator: VPLL2: 1800 mV normal standby regulator: VSIM: 1800 <--> 3000 mV normal standby i2c_omap i2c_omap.3: bus 3 rev3.12 at 100 kHz SCSI subsystem initialized twl4030_usb twl4030_usb: Initialized TWL4030 USB module usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb musb_hdrc: version 6.0, musb-dma, otg (peripheral+host), debug=0 musb_core_init 1421: reconfigure software for static FIFOs musb_hdrc musb_hdrc: musb_init_controller failed with status -19 NET: Registered protocol family 2 IP route cache hash table entries: 2048 (order: 1, 8192 bytes) TCP established hash table entries: 8192 (order: 4, 65536 bytes) TCP bind hash table entries: 8192 (order: 3, 32768 bytes) TCP: Hash tables configured (established 8192 bind 8192) TCP reno registered NET: Registered protocol family 1 NetWinder Floating Point Emulator V0.97 (double precision) ashmem: initialized VFS: Disk quotas dquot_6.5.2 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) JFFS2 version 2.2. (NAND) ? 2001-2006 Red Hat, Inc. msgmni has been set to 474 alg: No test for stdrng (krng) io scheduler noop registered io scheduler anticipatory registered (default) io scheduler deadline registered io scheduler cfq registered Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled serial8250.0: ttyS0 at MMIO 0x4806a000 (irq = 72) is a ST16654 serial8250.0: ttyS1 at MMIO 0x4806c000 (irq = 73) is a ST16654 serial8250.0: ttyS2 at MMIO 0x49020000 (irq = 74) is a ST16654 console [ttyS2] enabled brd: module loaded loop: module loaded i2c /dev entries driver Driver 'sd' needs updating - please use bus_type methods omap2-nand driver initializing NAND device: Manufacturer ID: 0x2c, Chip ID: 0xba (Micron NAND 256MiB 1,8V 16-bit) cmdlinepart partition parsing not available Creating 5 MTD partitions on "omap2-nand": 0x000000000000-0x000000080000 : "X-Loader" 0x000000080000-0x000000260000 : "U-Boot" 0x000000260000-0x000000280000 : "U-Boot Env" 0x000000280000-0x000000680000 : "Kernel" 0x000000680000-0x000010000000 : "File System" usbmon: debugfs is not available ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver ehci-omap ehci-omap.0: OMAP-EHCI Host Controller ehci-omap ehci-omap.0: new USB bus registered, assigned bus number 1 ehci-omap ehci-omap.0: irq 77, io mem 0x48064800 ehci-omap ehci-omap.0: USB 2.0 started, EHCI 1.00 usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb1: Product: OMAP-EHCI Host Controller usb usb1: Manufacturer: Linux 2.6.29-omap1-07255-g85f0546 ehci_hcd usb usb1: SerialNumber: ehci-omap.0 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 3 ports detected Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. android init twl4030_rtc twl4030_rtc: rtc core: registered twl4030_rtc as rtc0 twl4030_rtc twl4030_rtc: Power up reset detected. twl4030_rtc twl4030_rtc: Enabling TWL4030-RTC. mmci-omap-hs mmci-omap-hs.0: Failed to get debounce clock usbcore: registered new interface driver usbhid usbhid: v2.6:USB HID core driver logger: created 64K log 'log_main' logger: created 256K log 'log_events' logger: created 64K log 'log_radio' Advanced Linux Sound Architecture Driver Version 1.0.18a. No device for DAI AD73311 No device for DAI AK4535 No device for DAI CS4270 No device for DAI PCM3008 HiFi No device for DAI SSM2602 No device for DAI tlv320aic23 No device for DAI tlv320aic3x No device for DAI twl4030 No device for DAI UDA134X No device for DAI UDA1380 No device for DAI UDA1380 No device for DAI UDA1380 No device for DAI WM8510 HiFi No device for DAI WM8580 PAIFRX No device for DAI WM8580 PAIFTX No device for DAI WM8728 No device for DAI WM8731 No device for DAI WM8750 No device for DAI WM8753 DAI 0 No device for DAI WM8753 DAI 1 No device for DAI WM8971 No device for DAI WM8990 ADC/DAC Primary No device for DAI omap-mcbsp-dai-0 No device for DAI omap-mcbsp-dai-1 No device for DAI omap-mcbsp-dai-2 No device for DAI omap-mcbsp-dai-3 No device for DAI omap-mcbsp-dai-4 OMAP3 Beagle SoC init TWL4030 Audio Codec init asoc: twl4030 <-> omap-mcbsp-dai-0 mapping ok ALSA device list: #0: omap3beagle (twl4030) TCP cubic registered NET: Registered protocol family 17 NET: Registered protocol family 15 RPC: Registered udp transport module. RPC: Registered tcp transport module. Power Management for TI OMAP3. VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 1 Console: switching to colour frame buffer device 80x30 clock: clksel_round_rate_div: dpll4_m4_ck target_rate 36000000 clock: new_div = 12, new_rate = 36000000 omapdss: Could not find exact pixel clock. Requested 23500 kHz, got 24000 kHz usb 1-2: new high speed USB device using ehci-omap and address 2 twl4030_rtc twl4030_rtc: setting system clock to 2000-01-01 00:00:00 UTC (946684800) Waiting 1sec before mounting root device... usb 1-2: New USB device found, idVendor=0424, idProduct=2512 usb 1-2: New USB device strings: Mfr=0, Product=0, SerialNumber=0 usb 1-2: configuration #1 chosen from 1 choice hub 1-2:1.0: USB hub found hub 1-2:1.0: 2 ports detected mmc0: new SD card at address 8935 mmcblk0: mmc0:8935 SM02G 1.87 GiB mmcblk0:<7>usb 1-2: link qh256-0001/ffc00100 start 255 [1/0 us] p1 p2 kjournald starting. Commit interval 5 seconds EXT3-fs warning: maximal mount count reached, running e2fsck is recommended EXT3 FS on mmcblk0p2, internal journal EXT3-fs: recovery complete. EXT3-fs: mounted filesystem with ordered data mode. VFS: Mounted root (ext3 filesystem) on device 179:2. Freeing init memory: 144K init: cannot open '/initlogo.rle' init: cannot find '/system/bin/playmp3', disabling 'bootsound' # warning: `rild' uses 32-bit capabilities (legacy support in use)
//////////////////////////////////////////////////////////////////////////////////////////// The beagle stucks overhere. Could anyone tell me why I can't enjoy Android??? I have stocked in 3 days .. I would appreciate .. Best Regards Michael -- unsubscribe: [email protected] website: http://groups.google.com/group/android-porting
