Thank you I have try the method as is described in the link，but it still has no signal.
On 6月9日, 下午6时20分, Uhrenfeldt Henrik <[email protected]> wrote: > Hi, > > It seems that the reply to the RIL_REQUEST_GPRS_REGISTRATION_STATE is not > formatted properly. The RIL interface for Éclair dictates this implementation: > > /** > * RIL_REQUEST_GPRS_REGISTRATION_STATE > * > * Request current GPRS registration state > * > * "data" is NULL > * "response" is a "char **" > * ((const char **)response)[0] is registration state 0-5 from TS 27.007 > 10.1.20 AT+CGREG > * ((const char **)response)[1] is LAC if registered or NULL if not > * ((const char **)response)[2] is CID if registered or NULL if not > * ((const char **)response)[3] indicates the available radio technology, > where: > * 0 == unknown > * 1 == GPRS only > * 2 == EDGE > * 3 == UMTS > * 9 == HSDPA > * 10 == HSUPA > * 11 == HSPA > * > * LAC and CID are in hexadecimal format. > * valid LAC are 0x0000 - 0xffff > * valid CID are 0x00000000 - 0x0fffffff > * > * Please note that registration state 4 ("unknown") is treated > * as "out of service" in the Android telephony system > * > * Valid errors: > * SUCCESS > * RADIO_NOT_AVAILABLE > * GENERIC_FAILURE > */ > > I remember tweaking the reference RIL for correct GPRS registration state > reporting for our setup with a broadband 3G modem. I believe the ST-E RIL got > it right. Take a peek inside: > > http://android.git.kernel.org/?p=platform/vendor/st-ericsson/u300.git... > > ..more specifically the function called requestRegistrationState, which > formats the reply for upper layers from the AT response. It also depends on > what your modem sends back - different modems could report in different ways. > > Try porting this exact function into your RIL. > > --- > Henrik Uhrenfeldt > Chief Software Engineer > Ixonos Denmark ApS > Niels Jernes Vej 10, > DK-9220 Aalborg Ø, Denmark > mobile +45 4030 2607 > email: [email protected]http://www.ixonos.com > > -----Original Message----- > From: [email protected] > [mailto:[email protected]] On Behalf Of bryan.c.hsu > Sent: 9. juni 2010 11:56 > To: [email protected]; 'android-porting' > Subject: 答复: [android-porting] signal of gprs is zero > > Hi, > I think u can check the parameters of the CREG or COPS. > It maybe caused by the wrong parameters from BP. > Maybe u need to modify ril implementation for these two AT commands. > Br. > > -----邮件原件----- > 发件人: [email protected] > [mailto:[email protected]] 代表 Weber > 发送时间: 2010年6月9日 17:06 > 收件人: android-porting > 主题: [android-porting] signal of gprs is zero > > Hi,everyone > I have ported eclair2.1 to my board. > at first ,I can dial a call and send sms(the signal are good--full or > nearly full) > but the gprs could not be used,mms can not be sent > then I found that the apns are empty ,so I modify the apns-conf.xml in > system/etc > > now I can see the G flag in the top bar,and the signal none(without > little cross)---if it is not connected there will be a little cross on > the signal flag > > here are the logs: > > 535 D/RILJ ( 781): [0027]< GPRS_REGISTRATION_STATE {2, ffffffff, > ffffffff} > 536 D/AT ( 676): > 537 D/AT ( 676): > 538 D/AT ( 676): +CREG: 2,2 > 539 D/AT ( 676): > 540 D/AT ( 676): > 541 D/AT ( 676): > 542 D/AT ( 676): OK > 543 D/AT ( 676): > 544 D/AT ( 676): AT< +CREG: 2,2 > 545 D/AT ( 676): AT< OK > 546 D/RIL ( 676): onRequest: QUERY_NETWORK_SELECTION_MODE > 547 D/AT ( 676): AT> AT+COPS? > 548 D/AT ( 676): AT+COPS? > 549 D/RILJ ( 781): [0028]< REGISTRATION_STATE {2, ffffffff, > ffffffff} > 550 W/GSM ( 781): error parsing RegistrationState: > java.lang.NumberFormatException: unable to parse 'ffffffff' as integer > > it seems that the GPRS state (fffffff) is wrong. > could you tell me what are the problems ? > Thanks > -Weber > > -- > unsubscribe: [email protected] > website:http://groups.google.com/group/android-porting > > -- > unsubscribe: [email protected] > website:http://groups.google.com/group/android-porting -- unsubscribe: [email protected] website: http://groups.google.com/group/android-porting
