I don't think GFX is the problem, unless the wiki says that should it be built. You can check why is mediaserver missing, the path to it's Android.mk is frameworks/base/media/mediaserver/, run the script at $MYDROID/build/envsetup.sh and then go to the mentioned path and run 'mm' so only mediaserver module is built. Then if everything goes right you should have it on your FS.
On Sep 23, 11:59 pm, venki <[email protected]> wrote: > '/system/bin/mediaserver' is missing. but /system/lib/libmedia.so is > present.. can you please suggest me how to find out y it is missing? I > follwed the same steps mentioned > inhttp://code.google.com/p/rowboat/wiki/ConfigureAndBuild, > except instructions under "Install the Android Graphics SGX SDK on > Host Machine". Do you think it created the problem? > > On Sep 23, 9:20 pm, RockNCode <[email protected]> wrote: > > > > > I think the problem is on this: > > > init: cannot find '/system/bin/mediaserver', disabling 'media' > > > I think you need to find out why mediaserver is missing on your File > > System. Look also for /system/lib/libmedia.so > > > Alex. > > > On Sep 23, 6:38 am, venki <[email protected]> wrote: > > > > Yes. I have done it and pasted last few lines in my previous reply. It > > > is waiting for sevice media.audio_policy... > > > > On Sep 23, 7:59 am, Dark Knight <[email protected]> wrote: > > > > > Hi, > > > > > Can you issue, "logcat" command from serial or adb connection, and > > > > check the output??? > > > > > Regards, > > > > Vaisakh P S > > > > (http://www.google.com/profiles/107371394824790211115) > > > > > On Sep 22, 8:50 pm, venki <[email protected]> wrote: > > > > > > Hi I hav a beagleboard rev C4. Followed steps mentioned > > > > > inhttp://code.google.com/p/rowboat/, downloaded source code for eclair > > > > > and built it. But dvi display got stuck at 'ANDROID" screen. Through > > > > > serial port i got following things. please can anybody help me to > > > > > solve this.... > > > > > > Texas Instruments X-Loader 1.4.2 (Feb 19 2009 - 12:01:24) > > > > > Reading boot sector > > > > > Loading u-boot.bin from nand > > > > > > U-Boot 2009.11-rc1-00601-g3aa4b51 (Jan 05 2010 - 20:56:38) > > > > > > OMAP3530-GP ES3.1, CPU-OPP2 L3-165MHz > > > > > OMAP3 Beagle board + LPDDR/NAND > > > > > I2C: ready > > > > > DRAM: 256 MB > > > > > NAND: 256 MiB > > > > > In: serial > > > > > Out: serial > > > > > Err: serial > > > > > Board revision C4 > > > > > Die ID #72bc000400000000040373050e00901a > > > > > Hit any key to stop autoboot: 0 > > > > > mmc0 is available > > > > > reading boot.scr > > > > > > ** Unable to read "boot.scr" from mmc 0:1 ** > > > > > reading uImage > > > > > > 2447360 bytes read > > > > > Booting from mmc ... > > > > > ## Booting kernel from Legacy Image at 82000000 ... > > > > > Image Name: Linux-2.6.32 > > > > > Image Type: ARM Linux Kernel Image (uncompressed) > > > > > Data Size: 2447296 Bytes = 2.3 MB > > > > > Load Address: 80008000 > > > > > Entry Point: 80008000 > > > > > Verifying Checksum ... OK > > > > > Loading Kernel Image ... OK > > > > > OK > > > > > > Starting kernel ... > > > > > > Uncompressing > > > > > Linux...................................................................... > > > > > .................................................................... > > > > > Linux version 2.6.32 (ve...@venki-laptop) (gcc version 4.4.0 (GCC) ) > > > > > #1 Tue Sep 21 19:41:07 IST 2010 > > > > > CPU: ARMv7 Processor [411fc083] revision 3 (ARMv7), cr=10c53c7f > > > > > CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache > > > > > Machine: OMAP3 Beagle Board > > > > > Memory policy: ECC disabled, Data cache writeback > > > > > OMAP3430/3530 ES3.1 (l2cache iva sgx neon isp 720m ) > > > > > SRAM: Mapped pa 0x40200000 to va 0xfe400000 size: 0x100000 > > > > > Reserving 12582912 bytes SDRAM for VRAM > > > > > Built 1 zonelists in Zone order, mobility grouping on. Total pages: > > > > > 65024 > > > > > Kernel command line: console=ttyS2,115200n8 vram=12M > > > > > omapdss.def_disp=dvi omapfb.mode=dvi:1024x768mr...@60 root=/dev/ > > > > > mmcblk0p2 init=/init rw rootwait > > > > > PID hash table entries: 1024 (order: 0, 4096 bytes) > > > > > Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) > > > > > Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) > > > > > Memory: 128MB 128MB = 256MB total > > > > > Memory: 242048KB available (4224K code, 818K data, 172K init, 0K > > > > > highmem) > > > > > Hierarchical RCU implementation. > > > > > NR_IRQS:402 > > > > > Clocking rate (Crystal/Core/MPU): 26.0/332/720 MHz > > > > > Reprogramming SDRC clock to 332000000 Hz > > > > > GPMC revision 5.0 > > > > > IRQ: Found an INTC at 0xfa200000 (revision 4.0) with 96 interrupts > > > > > Total of 96 interrupts on 1 active controller > > > > > OMAP GPIO hardware version 2.5 > > > > > OMAP clockevent source: GPTIMER12 at 32768 Hz > > > > > Console: colour dummy device 80x30 > > > > > Calibrating delay loop... 740.48 BogoMIPS (lpj=2891776) > > > > > Mount-cache hash table entries: 512 > > > > > CPU: Testing write buffer coherency: ok > > > > > regulator: core version 0.5 > > > > > NET: Registered protocol family 16 > > > > > Found NAND on CS0 > > > > > Registering NAND on CS0 > > > > > Unable to get DVI reset GPIO > > > > > OMAP DMA hardware revision 4.0 > > > > > bio: create slab <bio-0> at 0 > > > > > SCSI subsystem initialized > > > > > usbcore: registered new interface driver usbfs > > > > > usbcore: registered new interface driver hub > > > > > usbcore: registered new device driver usb > > > > > i2c_omap i2c_omap.1: bus 1 rev3.12 at 2600 kHz > > > > > twl4030: PIH (irq 7) chaining IRQs 368..375 > > > > > twl4030: power (irq 373) chaining IRQs 376..383 > > > > > twl4030: gpio (irq 368) chaining IRQs 384..401 > > > > > regulator: VUSB1V5: 1500 mV normal standby > > > > > regulator: VUSB1V8: 1800 mV normal standby > > > > > regulator: VUSB3V1: 3100 mV normal standby > > > > > twl4030_usb twl4030_usb: Initialized TWL4030 USB module > > > > > regulator: VMMC1: 1850 <--> 3150 mV normal standby > > > > > regulator: VDAC: 1800 mV normal standby > > > > > regulator: VPLL2: 1800 mV normal standby > > > > > regulator: VSIM: 1800 <--> 3000 mV normal standby > > > > > i2c_omap i2c_omap.2: bus 2 rev3.12 at 400 kHz > > > > > i2c_omap i2c_omap.3: bus 3 rev3.12 at 100 kHz > > > > > Switching to clocksource 32k_counter > > > > > musb_hdrc: version 6.0, musb-dma, otg (peripheral+host), debug=0 > > > > > musb_hdrc: USB OTG mode controller at fa0ab000 using DMA, IRQ 92 > > > > > NET: Registered protocol family 2 > > > > > IP route cache hash table entries: 2048 (order: 1, 8192 bytes) > > > > > TCP established hash table entries: 8192 (order: 4, 65536 bytes) > > > > > TCP bind hash table entries: 8192 (order: 3, 32768 bytes) > > > > > TCP: Hash tables configured (established 8192 bind 8192) > > > > > TCP reno registered > > > > > UDP hash table entries: 256 (order: 0, 4096 bytes) > > > > > UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) > > > > > NET: Registered protocol family 1 > > > > > RPC: Registered udp transport module. > > > > > RPC: Registered tcp transport module. > > > > > RPC: Registered tcp NFSv4.1 backchannel transport module. > > > > > omap-iommu omap-iommu.0: isp registered > > > > > NetWinder Floating Point Emulator V0.97 (double precision) > > > > > ashmem: initialized > > > > > VFS: Disk quotas dquot_6.5.2 > > > > > Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) > > > > > JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc. > > > > > msgmni has been set to 473 > > > > > alg: No test for stdrng (krng) > > > > > io scheduler noop registered > > > > > io scheduler deadline registered > > > > > io scheduler cfq registered (default) > > > > > OMAP DSS rev 2.0 > > > > > OMAP DISPC rev 3.0 > > > > > OMAP VENC rev 2 > > > > > Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled > > > > > serial8250.0: ttyS0 at MMIO 0x4806a000 (irq = 72) is a ST16654 > > > > > serial8250.1: ttyS1 at MMIO 0x4806c000 (irq = 73) is a ST16654 > > > > > serial8250.2: ttyS2 at MMIO 0x49020000 (irq = 74) is a ST16654 > > > > > console [ttyS2] enabled > > > > > brd: module loaded > > > > > loop: module loaded > > > > > usbcore: registered new interface driver asix > > > > > usbcore: registered new interface driver cdc_ether > > > > > usbcore: registered new interface driver cdc_eem > > > > > usbcore: registered new interface driver dm9601 > > > > > usbcore: registered new interface driver smsc95xx > > > > > usbcore: registered new interface driver gl620a > > > > > usbcore: registered new interface driver net1080 > > > > > usbcore: registered new interface driver plusb > > > > > usbcore: registered new interface driver rndis_host > > > > > usbcore: registered new interface driver cdc_subset > > > > > usbcore: registered new interface driver zaurus > > > > > usbcore: registered new interface driver MOSCHIP usb-ethernet driver > > > > > ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver > > > > > ehci-omap ehci-omap.0: OMAP-EHCI Host Controller > > > > > ehci-omap ehci-omap.0: new USB bus registered, assigned bus number 1 > > > > > ehci-omap ehci-omap.0: irq 77, io mem 0x48064800 > > > > > ehci-omap ehci-omap.0: USB 2.0 started, EHCI 1.00 > > > > > hub 1-0:1.0: USB hub found > > > > > hub 1-0:1.0: 3 ports detected > > > > > Initializing USB Mass Storage driver... > > > > > usbcore: registered new interface driver usb-storage > > > > > USB Mass Storage support registered. > > > > > android init > > > > > android_probe pdata: c048147c > > > > > android_bind > > > > > android_usb gadget: android_usb ready > > > > > musb_hdrc musb_hdrc: MUSB HDRC host driver > > > > > musb_hdrc musb_hdrc: new USB bus registered, assigned bus number 2 > > > > > hub 2-0:1.0: USB hub found > > > > > hub 2-0:1.0: 1 port detected > > > > > f_adb init > > > > > android_register_function adb > > > > > adb_bind_config > > > > > f_mass_storage init > > > > > android_register_function usb_mass_storage > > > > > mice: PS/2 mouse device common for all mice > > > > > input: gpio-keys as /devices/platform/gpio-keys/input/input0 > > > > > i2c /dev entries driver > > > > > Linux video capture interface: v2.00 > > > > > omap-iommu omap-iommu.0: isp: version 1.1 > > > > > OMAP Watchdog Timer Rev 0x31: initial timeout 60 sec > > > > > mmci-omap-hs mmci-omap-hs.1: err -16 configuring card detect > > > > > usbcore: registered new interface driver usbhid > > > > > usbhid: USB HID core > > ... > > read more » -- unsubscribe: [email protected] website: http://groups.google.com/group/android-porting
