Hi All, I am trying to bring up Froyo on Hawk board. But I am hitting an issue, after Kernel boots I have an error popping up "LAUNCH FAILED FORCE CLOSE". I am using Core Druid's Kernel and File system Boot argument I am using is bootargs=mem=128M console=ttyS2,115200n8 noinitrd root=/dev/sda1 rootwait rw init=/init ip=dhcp androidboot.console=ttyS2
Can anyone provide pointers on what is the issue is about and how it can be fixed. The Kernel log is as follows hawkboard.org > boot NAND read: device 0 offset 0x200000, size 0x200000 2097152 bytes read: OK ## Booting kernel from Legacy Image at c0700000 ... Image Name: Linux-2.6.32-rc6-g0e521ee Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 1958448 Bytes = 1.9 MB Load Address: c0008000 Entry Point: c0008000 Verifying Checksum ... OK Loading Kernel Image ... OK OK Starting kernel ... Linux version 2.6.32-rc6-g0e521ee (r...@sct-desktop) (gcc version 4.3.3 (Sourcery G++ Lite 2009q1-203) ) #1 PREEMPT Tue Sep 28 18:16:16 IST 2010 CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177 CPU: VIVT data cache, VIVT instruction cache Machine: OMAPL 138 Hawkboard.org Memory policy: ECC disabled, Data cache writeback DaVinci da850/omap-l138 variant 0x0 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512 Kernel command line: console=ttyS2,115200n8 console=tty1 noinitrd root=/dev/mmcblk0p1 rootwait rw init=/init ip=dhcp androidboot.console=ttyS2 Unknown boot option `androidboot.console=ttyS2': ignoring PID hash table entries: 512 (order: -1, 2048 bytes) Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) Memory: 128MB = 128MB total Memory: 125140KB available (3732K code, 726K data, 148K init, 0K highmem) SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 Hierarchical RCU implementation. NR_IRQS:245 Console: colour dummy device 80x30 Calibrating delay loop... 149.50 BogoMIPS (lpj=747520) Mount-cache hash table entries: 512 CPU: Testing write buffer coherency: ok DaVinci: 144 gpio irqs regulator: core version 0.5 NET: Registered protocol family 16 bio: create slab <bio-0> at 0 SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb Switching to clocksource timer0_1 musb_hdrc: version 6.0, cppi4.1-dma, (host+peripheral), debug=0 Waiting for USB PHY clock good... musb_hdrc: USB OTG mode controller at fee00000 using DMA, IRQ 58 musb_hdrc musb_hdrc: MUSB HDRC host driver musb_hdrc musb_hdrc: new USB bus registered, assigned bus number 1 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 4096 (order: 3, 32768 bytes) TCP bind hash table entries: 4096 (order: 2, 16384 bytes) TCP: Hash tables configured (established 4096 bind 4096) TCP reno registered NET: Registered protocol family 1 RPC: Registered udp transport module. RPC: Registered tcp transport module. RPC: Registered tcp NFSv4.1 backchannel transport module. ashmem: initialized JFFS2 version 2.2. (NAND) �© 2001-2006 Red Hat, Inc. msgmni has been set to 244 io scheduler noop registered io scheduler anticipatory registered (default) da8xx_lcdc da8xx_lcdc.0: GLCD: Found VGA_Monitor panel Console: switching to colour frame buffer device 80x30 Serial: 8250/16550 driver, 3 ports, IRQ sharing disabled serial8250.0: ttyS0 at MMIO 0x1c42000 (irq = 25) is a 16550A serial8250.0: ttyS1 at MMIO 0x1d0c000 (irq = 53) is a 16550A serial8250.0: ttyS2 at MMIO 0x1d0d000 (irq = 61) is a 16550A console [ttyS2] enabled brd: module loaded ahci ahci: forcing PORTS_IMPL to 0x1 ahci ahci: AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl SATA mode ahci ahci: flags: ncq sntf pm led clo only pmp pio slum part ccc scsi0 : ahci ata1: SATA max UDMA/133 irq 67 NAND device: Manufacturer ID: 0x2c, Chip ID: 0xa1 (Micron NAND 128MiB 1,8V 8-bit) Bad block table not found for chip 0 Bad block table not found for chip 0 Scanning device for bad blocks Creating 5 MTD partitions on "davinci_nand.1": 0x000000000000-0x000000020000 : "u-boot env" 0x000000020000-0x000000040000 : "UBL" 0x000000040000-0x0000000c0000 : "u-boot" 0x000000200000-0x000000400000 : "kernel" 0x000000400000-0x000008000000 : "filesystem" davinci_nand davinci_nand.1: controller rev. 2.5 console [netcon0] enabled netconsole: network logging started ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver ohci ohci.0: DA8xx OHCI ohci ohci.0: new USB bus registered, assigned bus number 2 ohci ohci.0: irq 59, io mem 0x01e25000 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 1 port detected Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. g_ether gadget: using random self ethernet address g_ether gadget: using random host ethernet address usb0: MAC 76:4a:d8:59:43:9b usb0: HOST MAC ee:4b:3c:34:2d:54 g_ether gadget: Ethernet Gadget, version: Memorial Day 2008 g_ether gadget: g_ether ready mice: PS/2 mouse device common for all mice i2c /dev entries driver watchdog watchdog: heartbeat 60 sec cpuidle: using governor ladder cpuidle: using governor menu davinci_mmc davinci_mmc.0: Using DMA, 4-bit mode usbcore: registered new interface driver usbhid usbhid: v2.6:USB HID core driver logger: created 64K log 'log_main' logger: created 256K log 'log_events' logger: created 64K log 'log_radio' logger: created 64K log 'log_system' Advanced Linux Sound Architecture Driver Version 1.0.21. No device for DAI tlv320aic3x asoc: tlv320aic3x <-> davinci-i2s mapping ok ALSA device list: #0: DA850/OMAP-L138 EVM (tlv320aic3x) mmc0: new high speed SD card at address b368 mmcblk0: mmc0:b368 SDC 1.85 GiB ata1: SATA link down (SStatus 0 SControl 300) TCP cubic registered NET: Registered protocol family 17 Clocks: disable unused emac Clocks: disable unused spi1 mmcblk0: p1 davinci_emac_probe: using random MAC addr: a6:ab:b0:80:73:2e emac-mii: probed usb 2-1: new low speed USB device using ohci and address 2 usb 2-1: configuration #1 chosen from 1 choice input: Logitech USB Keyboard as /devices/platform/ohci.0/usb2/2-1/2-1:1.0/input/input0 generic-usb 0003:046D:C31C.0001: input: USB HID v1.10 Keyboard [Logitech USB Keyboard] on usb-ohci.0-1/input0 input: Logitech USB Keyboard as /devices/platform/ohci.0/usb2/2-1/2-1:1.1/input/input1 generic-usb 0003:046D:C31C.0002: input: USB HID v1.10 Device [Logitech USB Keyboard] on usb-ohci.0-1/input1 eth0: attached PHY driver [Generic PHY] (mii_bus:phy_addr=1:07, id=7c0f1) IP-Config: Incomplete network configuration information. kjournald starting. Commit interval 5 seconds EXT3 FS on mmcblk0p1, internal journal EXT3-fs: recovery complete. EXT3-fs: mounted filesystem with writeback data mode. VFS: Mounted root (ext3 filesystem) on device 179:1. Freeing init memory: 148K Warning: unable to open an initial console. init: cannot open '/initlogo.rle' init: cannot find '/system/etc/install-recovery.sh', disabling 'flash_recovery' # warning: `rild' uses 32-bit capabilities (legacy support in use) binder: release 774:774 transaction 1502 out, still active binder: 689:689 transaction failed 29189, size 4-0 binder: send failed reply for transaction 1502, target dead -------------------------------------------BOOT STOPS HERE----------------------------------------------------------------- Thanks Srinidhi KV -- unsubscribe: [email protected] website: http://groups.google.com/group/android-porting
