Hi guys,
i used the MLO, uboot uimage and ubifs binaries given by my vendor and
tried to boot android on ema3530 stalker board,
i loaded the images into nand, and redirected the booting from nand..
following is the boot log..
please help me in booting..
U-Boot 2009.11 (Feb 18 2011 - 12:08:32)
OMAP3530-GP ES3.1, CPU-OPP2 L3-165MHz
OMAP3 SBC3530 + LPDDR/NAND
I2C: ready
DRAM: 128 MB
NAND: 256 MiB
In: serial
Out: serial
Err: serial
Ethernet MAC address: 02:c0:05:01:b0:05
Die ID #170000040000000004036ac00501b005
Net: smc911x-0
Hit any key to stop autoboot: 0
OMAP3 Stalker # setenv nandargs 'setenv bootargs console=${console}
vram=${vram} omapfb.mode=dvi:'
OMAP3 Stalker # setenv nandargs 'setenv bootargs omapfb.debug=y root=$
{nandroot}'
OMAP3 Stalker # setenv nandargs 'setenv bootargs omapdss.def_disp=$
{defaultdisplay}'
OMAP3 Stalker # setenv nandargs 'setenv bootargs init=/init rootfstype=
${nandrootfstype}'
OMAP3 Stalker # bootm
## Booting kernel from Legacy Image at 82000000 ...
Image Name: Linux-2.6.32
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2730600 Bytes = 2.6 MB
Load Address: 80008000
Entry Point: 80008000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK
Starting kernel ...
Uncompressing
Linux...............................................................................
U-Boot 2009.11 (Feb 18 2011 - 12:08:32)
OMAP3530-GP ES3.1, CPU-OPP2 L3-165MHz
OMAP3 SBC3530 + LPDDR/NAND
I2C: ready
DRAM: 128 MB
NAND: 256 MiB
In: serial
Out: serial
Err: serial
Ethernet MAC address: 02:c0:05:01:b0:05
Die ID #170000040000000004036ac00501b005
Net: smc911x-0
Hit any key to stop autoboot: 0
OMAP3 Stalker # setenv bootargs console=${console} vram=${vram}
OMAP3 Stalker # setenv bootargs omapfb.mode=dvi:${dvimode}
omapfb.debug=y
OMAP3 Stalker # setenv bootargs omapdss.def_disp=${defaultdisplay}
OMAP3 Stalker # setenv bootargs root=${nandroot} init=/init
OMAP3 Stalker # setenv bootargs rootfstype=${nandrootfstype}
OMAP3 Stalker # saveenv
Saving Environment to NAND...
Erasing Nand...
Erasing at 0x260000 -- 100% complete.
Writing to Nand... done
OMAP3 Stalker # boot
mmc1 is available
reading boot.scr
** Unable to read "boot.scr" from mmc 0:1 **
reading uImage
** Unable to read "uImage" from mmc 0:1 **
Booting from nand ...
NAND read: device 0 offset 0x280000, size 0x400000
4194304 bytes read: OK
## Booting kernel from Legacy Image at 82000000 ...
Image Name: Linux-2.6.32
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2730600 Bytes = 2.6 MB
Load Address: 80008000
Entry Point: 80008000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK
Starting kernel ...
Uncompressing
Linux...............................................................................
Linux version 2.6.32 (ema@ema3530) (gcc version 4.4.0 (GCC) ) #14
PREEMPT Fri Oct 15 15:17:09 CST0
CPU: ARMv7 Processor [411fc083] revision 3 (ARMv7), cr=10c53c7f
CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
Machine: OMAP3 STALKER
Memory policy: ECC disabled, Data cache writeback
OMAP3430/3530 ES3.1 (l2cache iva sgx neon isp )
SRAM: Mapped pa 0x40200000 to va 0xfe400000 size: 0x100000
Reserving 12582912 bytes SDRAM for VRAM
Built 1 zonelists in Zone order, mobility grouping on. Total pages:
32512
Kernel command line: console=ttyS0,115200n8 vram=12M omapfb.mode=dvi:
1024x768MR-16@60 omapfb.vides
boardmodel length mismatch, use default type:SBC35X-A2
PID hash table entries: 512 (order: -1, 2048 bytes)
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 128MB = 128MB total
Memory: 111544KB available (4756K code, 837K data, 188K init, 0K
highmem)
Hierarchical RCU implementation.
NR_IRQS:402
Clocking rate (Crystal/Core/MPU): 26.0/332/500 MHz
Reprogramming SDRC clock to 332000000 Hz
GPMC revision 5.0
IRQ: Found an INTC at 0xfa200000 (revision 4.0) with 96 interrupts
Total of 96 interrupts on 1 active controller
OMAP GPIO hardware version 2.5
OMAP clockevent source: GPTIMER12 at 32768 Hz
Console: colour dummy device 80x30
Calibrating delay loop... 511.52 BogoMIPS (lpj=1998848)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
regulator: core version 0.5
NET: Registered protocol family 16
EMA OMAP3XX Stalker Platform:
model: SBC35X-A2
eth: SMSC922x
usbhost: y
analog video in: y
hardward security: n
on board WIFI: n
Fram/Eeprom: 0 Kbit
omap3stalkerdc: Driver registration complete
Target VDD1 OPP = 5, VDD2 OPP = 3
OMAP DMA hardware revision 4.0
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
i2c_omap i2c_omap.1: bus 1 rev3.12 at 2600 kHz
twl4030: PIH (irq 7) chaining IRQs 368..375
twl4030: power (irq 373) chaining IRQs 376..383
twl4030: gpio (irq 368) chaining IRQs 384..401
regulator: VUSB1V5: 1500 mV normal standby
regulator: VUSB1V8: 1800 mV normal standby
regulator: VUSB3V1: 3100 mV normal standby
twl4030_usb twl4030_usb: Initialized TWL4030 USB module
regulator: VMMC1: 1850 <--> 3150 mV normal standby
regulator: VDAC: 1800 mV normal standby
i2c_omap i2c_omap.2: bus 2 rev3.12 at 400 kHz
i2c_omap i2c_omap.3: bus 3 rev3.12 at 400 kHz
Switching to clocksource 32k_counter
musb_hdrc: version 6.0, musb-dma, otg (peripheral+host), debug=0
musb_hdrc: USB OTG mode controller at fa0ab000 using DMA, IRQ 92
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
omap-iommu omap-iommu.0: isp registered
OMAP35x Linux PSP version 03.00.01.06 (OMAP3 STALKER)
NetWinder Floating Point Emulator V0.97 (double precision)
ashmem: initialized
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
JFFS2 version 2.2. (NAND) �© 2001-2006 Red Hat, Inc.
msgmni has been set to 218
alg: No test for stdrng (krng)
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
OMAP DSS rev 2.0
OMAP DISPC rev 3.0
OMAP VENC rev 2
Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
serial8250.0: ttyS0 at MMIO 0x4806a000 (irq = 72) is a ST16654
console [ttyS0] enabled
serial8250.1: ttyS1 at MMIO 0x4806c000 (irq = 73) is a ST16654
serial8250.2: ttyS2 at MMIO 0x49020000 (irq = 74) is a ST16654
brd: module loaded
loop: module loaded
omap2-nand driver initializing
NAND device: Manufacturer ID: 0x2c, Chip ID: 0xba (Micron NAND 256MiB
1,8V 16-bit)
Creating 5 MTD partitions on "omap2-nand.0":
0x000000000000-0x000000080000 : "X-Loader"
0x000000080000-0x000000260000 : "U-Boot"
0x000000260000-0x000000280000 : "U-Boot Env"
0x000000280000-0x000000680000 : "Kernel"
0x000000680000-0x000010000000 : "File System"
UBI: attaching mtd4 to ubi0
UBI: physical eraseblock size: 131072 bytes (128 KiB)
UBI: logical eraseblock size: 129024 bytes
UBI: smallest flash I/O unit: 2048
UBI: sub-page size: 512
UBI: VID header offset: 512 (aligned 512)
UBI: data offset: 2048
UBI: attached mtd4 to ubi0
UBI: MTD device name: "File System"
UBI: MTD device size: 249 MiB
UBI: number of good PEBs: 1996
UBI: number of bad PEBs: 0
UBI: max. allowed volumes: 128
UBI: wear-leveling threshold: 4096
UBI: number of internal volumes: 1
UBI: number of user volumes: 1
UBI: available PEBs: 0
UBI: total number of reserved PEBs: 1996
UBI: number of PEBs reserved for bad PEB handling: 19
UBI: max/mean erase counter: 1/0
UBI: image sequence number: 0
smsc911x: Driver version 2008-10-21.
UBI: background thread "ubi_bgt0d" started, PID 491
smsc911x-mdio: probed
eth0: attached PHY driver [Generic PHY] (mii_bus:phy_addr=ffffffff:01,
irq=-1)
net eth0: MAC Address: 02:00:17:00:00:04
dm9000 Ethernet Driver, V1.31
usbcore: registered new interface driver cdc_ether
usbcore: registered new interface driver dm9601
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-omap ehci-omap.0: OMAP-EHCI Host Controller
ehci-omap ehci-omap.0: new USB bus registered, assigned bus number 1
ehci-omap ehci-omap.0: irq 77, io mem 0x48064800
ehci-omap ehci-omap.0: USB 2.0 started, EHCI 1.00
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: OMAP-EHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.32 ehci_hcd
usb usb1: SerialNumber: ehci-omap.0
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 3 ports detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver usbtest
g_ether gadget: using random self ethernet address
g_ether gadget: using random host ethernet address
usb0: MAC b6:4d:e9:c1:8e:52
usb0: HOST MAC 5a:b6:c2:37:a3:2d
g_ether gadget: Ethernet Gadget, version: Memorial Day 2008
g_ether gadget: g_ether ready
musb_hdrc musb_hdrc: MUSB HDRC host driver
musb_hdrc musb_hdrc: new USB bus registered, assigned bus number 2
usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: MUSB HDRC host driver
usb usb2: Manufacturer: Linux 2.6.32 musb-hcd
usb usb2: SerialNumber: musb_hdrc
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
input: gpio-keys as /devices/platform/gpio-keys/input/input0
input: TWL4030 Keypad as /devices/platform/i2c_omap.1/i2c-1/1-004a/
twl4030_keypad/input/input1
ads7846 spi1.0: touchscreen, irq 180
input: ADS7846 Touchscreen as /devices/platform/omap2_mcspi.1/spi1.0/
input/input2
input: twl4030_pwrbutton as /devices/platform/i2c_omap.1/i2c-1/1-0049/
twl4030_pwrbutton/input/inp3
using rtc device, twl_rtc, for alarms
twl_rtc twl_rtc: rtc core: registered twl_rtc as rtc0
i2c /dev entries driver
Linux video capture interface: v2.00
tvp514x 2-005d: Registered to v4l2 master omap34xxcam!!
omap-iommu omap-iommu.0: isp: version 1.1
usbcore: registered new interface driver uvcvideo
USB Video Class driver (v0.1.0)
OMAP Watchdog Timer Rev 0x31: initial timeout 60 sec
Registered led device: stalker:D8:usr0
Registered led device: stalker:D9:usr1
Registered led device: stalker:D3:mmc0
Registered led device: stalker:D4:heartbeat
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
logger: created 64K log 'log_main'
logger: created 256K log 'log_events'
logger: created 64K log 'log_radio'
logger: created 64K log 'log_system'
Advanced Linux Sound Architecture Driver Version 1.0.21.
usbcore: registered new interface driver snd-usb-audio
No device for DAI wl1271bt
No device for DAI omap-mcbsp-dai-0
No device for DAI omap-mcbsp-dai-1
No device for DAI omap-mcbsp-dai-2
No device for DAI omap-mcbsp-dai-3
No device for DAI omap-mcbsp-dai-4
OMAP3 STALKER SoC init
asoc: twl4030 <-> omap-mcbsp-dai-0 mapping ok
asoc: wl1271bt <-> omap-mcbsp-dai-1 mapping ok
ALSA device list:
#0: omap3stalker (twl4030)
TCP cubic registered
NET: Registered protocol family 17
NET: Registered protocol family 15
Power Management for TI OMAP3.
Switched to new clocking rate (Crystal/Core/MPU): 26.0/332/600 MHz
IVA2 clocking rate: 430 MHz
SmartReflex driver initialized
VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev
1
fbcvt: 1024x768@60: CVT Name - .786M3-R
mmc0: new SDHC card at address e624
mmcblk0: mmc0:e624 SD04G 3.69 GiB
mmcblk0:
regulator_init_complete: disabling VDAC
twl_rtc twl_rtc: setting system clock to 2000-01-01 00:06:36 UTC
(946685196)
p1 p2
tvp514x 2-005d: chip id mismatch msb:0xfb lsb:0xfb
tvp514x 2-005d: Unable to detect decoder
tvp514x 2-005d: chip id mismatch msb:0xfb lsb:0xfb
tvp514x 2-005d: Unable to detect decoder
tvp514x 2-005d: chip id mismatch msb:0xfb lsb:0xfb
tvp514x 2-005d: Unable to detect decoder
tvp514x 2-005d: chip id mismatch msb:0xfb lsb:0xfb
tvp514x 2-005d: Unable to detect decoder
omapdss DPI error: display already enabled
omap_vout omap_vout: 'dvi' Display already enabled
omapdss DPI error: display already enabled
omap_vout omap_vout: 'dvi' Display already enabled
omap_vout omap_vout: Buffer Size = 3686400
omap_vout omap_vout: : registered and initialized video device 0
UBIFS: recovery needed
UBIFS: recovery completed
UBIFS: mounted UBI device 0, volume 0, name "rootfs"
UBIFS: file system size: 103348224 bytes (100926 KiB, 98 MiB, 801
LEBs)
UBIFS: journal size: 9033728 bytes (8822 KiB, 8 MiB, 71 LEBs)
UBIFS: media format: w4/r0 (latest is w4/r0)
UBIFS: default compressor: lzo
UBIFS: reserved for root: 0 bytes (0 KiB)
VFS: Mounted root (ubifs filesystem) on device 0:12.
Freeing init memory: 188K
Warning: unable to open an initial console.
init: cannot open '/initlogo.rle'
init: cannot find '/system/bin/playmp3', disabling 'bootsound'
FAT: invalid media value (0x00)
VFS: Can't find a valid FAT filesystem on dev mmcblk0.
sh: can't access tty; job control turned off
# warning: `rild' uses 32-bit capabilities (legacy support in use)
Thank You guys.. please tell me what is wrong.. and what should be
done to port android successfully.
--
unsubscribe: [email protected]
website: http://groups.google.com/group/android-porting
