Dear ML, Yesterday I tried Narcissus basic system (task-base, console) for my Hawkboard but I had some problem during boot:
[ 0.000000] Linux version 2.6.33-rc4 (ventoneicape...@ulisse) (gcc version 4.3.3 (GCC) ) #1 PREEMPT Thu May 13 16:36:51 CEST 2010 [ 0.000000] CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177 [ 0.000000] CPU: VIVT data cache, VIVT instruction cache [ 0.000000] Machine: DaVinci DA850/OMAP-L138/AM18xx Hawkboard(.org) [ 0.000000] Memory policy: ECC disabled, Data cache writeback [ 0.000000] DaVinci da850/omap-l138 variant 0x0 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512 [ 0.000000] Kernel command line: mem=128M console=ttyS2,115200n8 ip=192.168.0.200 root=/dev/nfs nfsroot=192.168.0.1:/nfsroot eth=0a:c1:a8:12:fa:c0 earlypr8 [ 0.000000] bootconsole [earlycon0] enabled [ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes) [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Memory: 128MB = 128MB total [ 0.000000] Memory: 124372KB available (4496K code, 426K data, 468K init, 0K highmem) [ 0.000000] SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] Hierarchical RCU implementation. [ 0.000000] NR_IRQS:245 [ 0.000000] Console: colour dummy device 80x30 [ 0.000000] Calibrating delay loop... 149.50 BogoMIPS (lpj=747520) [ 0.210000] Mount-cache hash table entries: 512 [ 0.210000] CPU: Testing write buffer coherency: ok [ 0.220000] devtmpfs: initialized [ 0.230000] DaVinci: 144 gpio irqs [ 0.240000] NET: Registered protocol family 16 [ 0.270000] WARNING: both McASP and McBSP are enabled, but they share pins. [ 0.270000] Disable one of them. [ 0.310000] bio: create slab <bio-0> at 0 [ 0.310000] SCSI subsystem initialized [ 0.320000] usbcore: registered new interface driver usbfs [ 0.330000] usbcore: registered new interface driver hub [ 0.330000] usbcore: registered new device driver usb [ 0.340000] i2c-gpio i2c-gpio.1: using pins 20 (SDA) and 21 (SCL) [ 0.350000] vpif vpif: vpif probe success [ 0.350000] Switching to clocksource timer0_1 Note: same problem occurs building a system with OE (.dev). Does anybody in ML have the same problem? I think that "[ 0.270000] WARNING: both McASP and McBSP are enabled, but they share pins." could indicate the solution, what do you think? Thank you for your help, pz _______________________________________________ Angstrom-distro-devel mailing list [email protected] http://lists.linuxtogo.org/cgi-bin/mailman/listinfo/angstrom-distro-devel
