Hello
I created
Angstrom-XFCE-NetworkManager-image-eglibc-ipk-v2012.05-beagleboard.rootfs.tar.bz2
and
Angstrom-systemd-GNOME-image-eglibc-ipk-v2012.05-beagleboard.rootfs.tar.bz2.
The XFCE on the serial port and display boots to the prompt but not into
X. The GNOME doesn't even boot to the prompt.
/lib/systemd/system/default.target is listed below for the XFCE
How do you make the system boot to X?
# This file is part of systemd.
#
# systemd is free software; you can redistribute it and/or modify it
# under the terms of the GNU General Public License as published by
# the Free Software Foundation; either version 2 of the License, or
# (at your option) any later version.
# See systemd.special(7) for details
[Unit]
Description=Graphical Interface
Requires=multi-user.target
After=multi-user.target
Conflicts=rescue.target
AllowIsolate=yes
[Install]
Alias=default.target
The following is the serial for XFCE boot on the the serial port
[vidal@ws008 ~]$ cat xfce.txt
* - * Qodem 0.1.2 Capture Generated Sat, 30 Jun 2012 12:04:52 -0600 BEGIN *
- *
U-Boot SPL 2011.12-dirty (Jun 29 2012 - 23:53:16)
Texas Instruments Revision detection unimplemented
OMAP SD/MMC: 0
timed out in wait_for_bb: I2C_STAT=1000
reading u-boot.img
reading u-boot.img
U-Boot 2011.12-dirty (Jun 29 2012 - 23:53:16)
OMAP3630/3730-GP ES1.2, CPU-OPP2, L3-165MHz, Max CPU Clock 1 Ghz
OMAP3 Beagle board + LPDDR/NAND
I2C: ready
DRAM: 512 MiB
NAND: 0 MiB
MMC: OMAP SD/MMC: 0
*** Warning - readenv() failed, using default environment
In: serial
Out: serial
Err: serial
Beagle xM Rev C
No EEPROM on expansion board
No EEPROM on expansion board
Die ID #158000029ff800000160a7450b02602d
Net: Net Initialization Skipped
No ethernet found.
Hit any key to stop autoboot: 2 1 0
The user button is currently NOT pressed.
SD/MMC found on device 0
reading uEnv.txt
130 bytes read
Loaded environment from uEnv.txt
Importing environment from mmc ...
Loading file "/boot/uImage" from mmc device 0:2 xxa2
4385648 bytes read
Booting from mmc ...
## Booting kernel from Legacy Image at 80200000 ...
Image Name: Angstrom/3.2.18/beagleboard
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 4385584 Bytes = 4.2 MiB
Load Address: 80008000
Entry Point: 80008000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 3.2.18 (vi...@ws008.swbell.net) (gcc version
4.5.4 20120305 (prerelease) (GCC) ) #1 Fri Jun 29 15:35:31 MDT 2012
[ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7),
cr=10c5387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing
instruction cache
[ 0.000000] Machine: OMAP3 Beagle Board
[ 0.000000] Beagle expansionboard: none
[ 0.000000] Beagle second expansionboard: none
[ 0.000000] Reserving 16777216 bytes SDRAM for VRAM
[ 0.000000] Memory policy: ECC disabled, Data cache writeback
[ 0.000000] OMAP3630 ES1.2 (l2cache iva sgx neon isp 192mhz_clk )
[ 0.000000] Clocking rate (Crystal/Core/MPU): 26.0/400/600 MHz
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on.
Total pages: 124416
[ 0.000000] Kernel command line: console=tty0 console=ttyO2,115200n8
consoleblank=0 mpurate=auto buddy=none buddy2=none camera=none vram=16
M omapfb.mode=dvi:hd720 omapfb.vram=0:8M,1:4M,2:4M omapdss.def_disp=dvi
root=/dev/mmcblk0p2 ro rootfstype=ext4 rootwait
[ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144
bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072
bytes)
[ 0.000000] allocated 2097152 bytes of page_cgroup
[ 0.000000] please try 'cgroup_disable=memory' option if you don't want
memory cgroups
[ 0.000000] Memory: 490MB = 490MB total
[ 0.000000] Memory: 486344k/486344k available, 37944k reserved, 0K
highmem
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] vmalloc : 0xe0800000 - 0xf8000000 ( 376 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xe0000000 ( 512 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000] .text : 0xc0008000 - 0xc0741cec (7400 kB)
[ 0.000000] .init : 0xc0742000 - 0xc0788000 ( 280 kB)
[ 0.000000] .data : 0xc0788000 - 0xc07e2710 ( 362 kB)
[ 0.000000] .bss : 0xc07e2734 - 0xc089f854 ( 757 kB)
[ 0.000000] SLUB: Genslabs=11, HWalign=64, Order=0-3, MinObjects=0,
CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:410 nr_irqs:410 410
[ 0.000000] IRQ: Found an INTC at 0xfa200000 (revision 4.0) with 96
interrupts
[ 0.000000] Total of 96 interrupts on 1 active controller
[ 0.000000] OMAP clockevent source: GPTIMER12 at 32768 Hz
[ 0.000000] sched_clock: 32 bits at 32kHz, resolution 30517ns, wraps
every 131071999ms
[ 0.000000] Console: colour dummy device 80x30
[ 0.000000] console [tty0] enabled
[ 0.000610] Calibrating delay loop... 506.27 BogoMIPS (lpj=1978368)
[ 0.039794] pid_max: default: 32768 minimum: 301
[ 0.040039] Security Framework initialized
[ 0.040100] AppArmor: AppArmor initialized
[ 0.040344] Mount-cache hash table entries: 512
[ 0.040771] Initializing cgroup subsys cpuacct
[ 0.040802] Initializing cgroup subsys memory
[ 0.040863] Initializing cgroup subsys devices
[ 0.040893] Initializing cgroup subsys freezer
[ 0.040924] Initializing cgroup subsys blkio
[ 0.040954] Initializing cgroup subsys perf_event
[ 0.041046] CPU: Testing write buffer coherency: ok
[ 0.042114] devtmpfs: initialized
[ 0.045745] print_constraints: dummy:
[ 0.046020] NET: Registered protocol family 16
[ 0.046203] GPMC revision 5.0
[ 0.047637] OMAP GPIO hardware version 2.5
[ 0.048980] omap_mux_init: Add partition: #1: core, flags: 0
[ 0.050292] OMAP3 Beagle Rev: xM C
[ 0.053344] Reprogramming SDRC clock to 400000000 Hz
[ 0.053375] dpll3_m2_clk rate change failed: -22
[ 0.055236] Found NAND on CS0
[ 0.055267] Registering NAND on CS0
[ 0.055572] Unable to get DVI reset GPIO
[ 0.055725] hw-breakpoint: debug architecture 0x4 unsupported.
[ 0.059265] omap-mcbsp.2: alias fck already exists
[ 0.059478] omap-mcbsp.3: alias fck already exists
[ 0.060638] OMAP DMA hardware revision 5.0
[ 0.067474] bio: create slab <bio-0> at 0
[ 0.068725] SCSI subsystem initialized
[ 0.069885] usbcore: registered new interface driver usbfs
[ 0.070068] usbcore: registered new interface driver hub
[ 0.070251] usbcore: registered new device driver usb
[ 0.070983] omap_i2c omap_i2c.1: bus 1 rev1.4.0 at 2600 kHz
[ 0.073394] twl4030: PIH (irq 7) chaining IRQs 368..375
[ 0.073516] twl4030: power (irq 373) chaining IRQs 376..383
[ 0.074005] twl4030: gpio (irq 368) chaining IRQs 384..401
[ 0.074371] _omap_mux_init_gpio: Could not set gpio192
[ 0.077148] print_constraints: VUSB1V5: 1500 mV normal standby
[ 0.077575] print_constraints: VUSB1V8: 1800 mV normal standby
[ 0.077972] print_constraints: VUSB3V1: 3100 mV normal standby
[ 0.079650] twl4030_usb twl4030_usb: Initialized TWL4030 USB module
[ 0.080413] print_constraints: VMMC1: 1850 <--> 3150 mV at 3150 mV
normal standby
[ 0.080871] print_constraints: VDAC: 1800 mV normal standby
[ 0.081268] print_constraints: VAUX2_4030: 1800 mV normal
[ 0.081695] print_constraints: VDVI: 1800 mV normal standby
[ 0.082183] print_constraints: VSIM: 1800 <--> 3000 mV at 1800 mV normal
standby
[ 0.082519] omap_i2c omap_i2c.2: bus 2 rev1.4.0 at 400 kHz
[ 0.092895] omap_i2c omap_i2c.3: bus 3 rev1.4.0 at 100 kHz
[ 0.094024] NetLabel: Initializing
[ 0.094055] NetLabel: domain hash size = 128
[ 0.094085] NetLabel: protocols = UNLABELED CIPSOv4
[ 0.094146] NetLabel: unlabeled traffic allowed by default
[ 0.094207] Switching to clocksource 32k_counter
[ 0.107696] AppArmor: AppArmor Filesystem Enabled
[ 0.119995] musb-hdrc: version 6.0, ?dma?, otg (peripheral+host)
[ 0.129882] musb-hdrc musb-hdrc: USB OTG mode controller at fa0ab000
using DMA, IRQ 92
[ 0.130249] NET: Registered protocol family 2
[ 0.130554] IP route cache hash table entries: 4096 (order: 2, 16384
bytes)
[ 0.131317] TCP established hash table entries: 16384 (order: 5, 131072
bytes)
[ 0.131683] TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.131927] TCP: Hash tables configured (established 16384 bind 16384)
[ 0.131958] TCP reno registered
[ 0.131958] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.132019] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.132354] NET: Registered protocol family 1
[ 0.132873] RPC: Registered named UNIX socket transport module.
[ 0.132904] RPC: Registered udp transport module.
[ 0.132904] RPC: Registered tcp transport module.
[ 0.132934] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.133209] omap_dsp_init: 600000 bytes @ 9ea00000
[ 0.134979] audit: initializing netlink socket (disabled)
[ 0.135070] type=2000 audit(0.148:1): initialized
[ 0.348052] VFS: Disk quotas dquot_6.5.2
[ 0.348419] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.351959] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[ 0.352172] fuse init (API version 7.17)
[ 0.354125] Btrfs loaded
[ 0.354187] msgmni has been set to 949
[ 0.355712] Block layer SCSI generic (bsg) driver version 0.4 loaded
(major 253)
[ 0.355865] io scheduler noop registered
[ 0.355895] io scheduler deadline registered
[ 0.355957] io scheduler cfq registered (default)
[ 0.356872] OMAP DSS rev 2.0
[ 0.359588] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 0.360992] omap_uart.0: ttyO0 at MMIO 0x4806a000 (irq = 72) is a OMAP
UART0
[ 0.361297] omap_uart.1: ttyO1 at MMIO 0x4806c000 (irq = 73) is a OMAP
UART1
[ 0.361572] omap_uart.2: ttyO2 at MMIO 0x49020000 (irq = 74) is a OMAP
UART2
[ 1.090606] console [ttyO2] enabled
[ 1.094696] omap_uart.3: ttyO3 at MMIO 0x49042000 (irq = 80) is a OMAP
UART3
[ 1.102722] [drm] Initialized drm 1.1.0 20060810
[ 1.115325] brd: module loaded
[ 1.122711] loop: module loaded
[ 1.128936] twl4030_madc twl4030_madc: clk disabled, enabling
[ 1.136962] omap2-nand driver initializing
[ 1.141693] No NAND device found
[ 1.145324] No NAND device found
[ 1.148956] OneNAND driver initializing
[ 1.153747] usbcore: registered new interface driver cdc_ether
[ 1.160034] usbcore: registered new interface driver rndis_host
[ 1.166381] cdc_ncm: 04-Aug-2011
[ 1.169830] usbcore: registered new interface driver cdc_ncm
[ 1.176269] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 3.196075] ehci-omap ehci-omap.0: OMAP-EHCI Host Controller
[ 3.202331] ehci-omap ehci-omap.0: new USB bus registered, assigned bus
number 1
[ 3.210357] ehci-omap ehci-omap.0: irq 77, io mem 0x48064800
[ 3.227386] ehci-omap ehci-omap.0: USB 2.0 started, EHCI 1.00
[ 3.233520] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 3.240783] usb usb1: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 3.248474] usb usb1: Product: OMAP-EHCI Host Controller
[ 3.254180] usb usb1: Manufacturer: Linux 3.2.18 ehci_hcd
[ 3.259948] usb usb1: SerialNumber: ehci-omap.0
[ 3.265472] hub 1-0:1.0: USB hub found
[ 3.269531] hub 1-0:1.0: 3 ports detected
[ 3.305419] Initializing USB Mass Storage driver...
[ 3.310699] usbcore: registered new interface driver usb-storage
[ 3.317108] USB Mass Storage support registered.
[ 3.322174] usbcore: registered new interface driver libusual
[ 3.328399] udc: OMAP UDC driver, version: 4 October 2004 (iso) (dma)
[ 3.335723] mousedev: PS/2 mouse device common for all mice
[ 3.343811] input: twl4030_pwrbutton as
/devices/platform/omap/omap_i2c.1/i2c-1/1-0049/twl4030_pwrbutton/input/input0
[ 3.355682] i2c /dev entries driver
[ 3.360076] Linux media interface: v0.10
[ 3.364318] lirc_dev: IR Remote Control driver registered, major 249
[ 3.371215] Driver for 1-wire Dallas network protocol.
[ 3.377410] OMAP Watchdog Timer Rev 0x31: initial timeout 60 sec
[ 3.384521] twl4030_wdt twl4030_wdt: Failed to register misc device
[ 3.391235] twl4030_wdt: probe of twl4030_wdt failed with error -16
[ 3.399017] device-mapper: ioctl: 4.22.0-ioctl (2011-10-19) initialised:
dm-de...@redhat.com
[ 3.408447] cpuidle: using governor ladder
[ 3.412719] cpuidle: using governor menu
[ 3.416931] sdhci: Secure Digital Host Controller Interface driver
[ 3.423522] sdhci: Copyright(c) Pierre Ossman
[ 3.602508] usb 1-2: new high-speed USB device number 2 using ehci-omap
[ 3.652221] omap_hsmmc: probe of omap_hsmmc.1 failed with error -16
[ 3.660552] usbcore: registered new interface driver usbhid
[ 3.666534] usbhid: USB HID core driver
[ 3.670532] oprofile: hardware counters not available
[ 3.675933] oprofile: using timer interrupt.
[ 3.681213] TCP cubic registered
[ 3.685424] NET: Registered protocol family 10
[ 3.691741] NET: Registered protocol family 17
[ 3.696655] Registering the dns_resolver key type
[ 3.701599] VFP support v0.3: implementor 41 architecture 3 part 30
variant c rev 3
[ 3.709716] ThumbEE CPU extension supported.
[ 3.714294] Registering SWP/SWPB emulation handler
[ 3.723205] sr_init: No PMIC hook to init smartreflex
[ 3.728820] smartreflex smartreflex.0: omap_sr_probe: SmartReflex driver
initialized
[ 3.737121] smartreflex smartreflex.1: omap_sr_probe: SmartReflex driver
initialized
[ 3.745361] SmartReflex Class3 initialized
[ 3.753173] clock: disabling unused clocks to save power
[ 3.759674] registered taskstats version 1
[ 3.814697] usb 1-2: New USB device found, idVendor=0424, idProduct=9514
[ 3.821838] usb 1-2: New USB device strings: Mfr=0, Product=0,
SerialNumber=0
[ 3.830444] hub 1-2:1.0: USB hub found
[ 3.849975] Console: switching to colour frame buffer device 160x45
[ 3.871490] hub 1-2:1.0: 5 ports detected
[ 3.879180] regulator_init_complete: VDAC: incomplete constraints,
leaving on
[ 3.886993] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[ 3.898040] Waiting for root device /dev/mmcblk0p2...
[ 4.180877] usb 1-2.1: new high-speed USB device number 3 using ehci-omap
[ 4.291076] mmc0: host does not support reading read-only switch.
assuming write-enable.
[ 4.302490] mmc0: new high speed SDHC card at address 0007
[ 4.309082] mmcblk0: mmc0:0007 SD8GB 7.42 GiB
[ 4.315002] usb 1-2.1: New USB device found, idVendor=0424,
idProduct=ec00
[ 4.322509] usb 1-2.1: New USB device strings: Mfr=0, Product=0,
SerialNumber=0
[ 4.330780] mmcblk0: p1 p2
[ 4.422882] usb 1-2.3: new low-speed USB device number 4 using ehci-omap
[ 4.450744] EXT4-fs (mmcblk0p2): INFO: recovery required on readonly
filesystem
[ 4.463592] EXT4-fs (mmcblk0p2): write access will be enabled during
recovery
[ 4.572845] usb 1-2.3: New USB device found, idVendor=0a81,
idProduct=0101
[ 4.585235] usb 1-2.3: New USB device strings: Mfr=1, Product=2,
SerialNumber=0
[ 4.597991] usb 1-2.3: Product: USB Keyboard
[ 4.607421] usb 1-2.3: Manufacturer: CHESEN
[ 4.623626] input: CHESEN USB Keyboard as
/devices/platform/usbhs-omap.0/ehci-omap.0/usb1/1-2/1-2.3/1-2.3:1.0/input/input1
[ 4.641021] generic-usb 0003:0A81:0101.0001: input,hidraw0: USB HID
v1.10 Keyboard [CHESEN USB Keyboard] on usb-ehci-omap.0-2.3/input0
[ 4.667114] input: CHESEN USB Keyboard as
/devices/platform/usbhs-omap.0/ehci-omap.0/usb1/1-2/1-2.3/1-2.3:1.1/input/input2
[ 4.684783] generic-usb 0003:0A81:0101.0002: input,hidraw1: USB HID
v1.10 Device [CHESEN USB Keyboard] on usb-ehci-omap.0-2.3/input1
[ 4.790191] usb 1-2.5: new low-speed USB device number 5 using ehci-omap
[ 4.919219] usb 1-2.5: New USB device found, idVendor=093a,
idProduct=2510
[ 4.932373] usb 1-2.5: New USB device strings: Mfr=1, Product=2,
SerialNumber=0
[ 4.945922] usb 1-2.5: Product: USB Optical Mouse
[ 4.956634] usb 1-2.5: Manufacturer: PixArt
[ 4.970916] input: PixArt USB Optical Mouse as
/devices/platform/usbhs-omap.0/ehci-omap.0/usb1/1-2/1-2.5/1-2.5:1.0/input/input3
[ 4.989624] generic-usb 0003:093A:2510.0003: input,hidraw2: USB HID
v1.11 Mouse [PixArt USB Optical Mouse] on usb-ehci-omap.0-2.5/input0
[ 9.389495] EXT4-fs (mmcblk0p2): recovery complete
[ 9.932159] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data
mode. Opts: (null)
[ 9.947174] VFS: Mounted root (ext4 filesystem) readonly on device 179:2.
[ 9.965789] devtmpfs: mounted
[ 9.975524] Freeing init memory: 280K
Welcome to The �ngström Distribution!
Starting udev Coldplug all
Devices...
Starting Remount API
VFS...
Starting Temporary
Directory...
Started Set Up Additional Binary Formats [
OK ]
Starting Debug File
System...
Starting POSIX Message Queue File
System...
Started Load Kernel Modules [
OK ]
Starting FUSE Control File
System...
Started Configuration File System [
OK ]
Started Huge Pages File System [
OK ]
Starting File System Check on Root
Device...
Started Apply Kernel Variables [
OK ]
Starting Journal
Service...
Started Journal Service [
OK ]
Starting udev Kernel Device
Manager...
[ 10.834320] udevd[61]: starting version 182
Started Remount API VFS [
OK ]
Started udev Kernel Device Manager [
OK ]
Started Temporary Directory [
OK ]
Started Debug File System [
OK ]
Started POSIX Message Queue File System [
OK ]
Started FUSE Control File System [
OK ]
Started udev Coldplug all Devices [
OK ]
systemd-fsck[58]: Angstrom: clean, 13581/454272 files, 110086/1815071 blocks
Started File System Check on Root Device [
OK ]
Starting Remount Root
FS...
[ 11.806121] EXT4-fs (mmcblk0p2): re-mounted. Opts: (null)
[ 11.830474] twl_rtc twl_rtc: Power up reset detected.
[ 11.843231] twl_rtc twl_rtc: Enabling TWL-RTC.
Started Remount Root FS [
OK ]
Started Machine ID first boot configure [
OK ]
Starting Load Random
Seed...
Starting Recreate Volatile Files and
Directories...
Started Run pending postinsts [
OK ]
Started Load Random Seed [
OK ]
Started Recreate Volatile Files and Directories [
OK ]
Starting Console System Startup
Logging...
Starting Avahi mDNS/DNS-SD
Stack...
[ 12.087219] twl_rtc twl_rtc: rtc core: registered twl_rtc as rtc0
Starting Timestamping
service...
Started Timestamping service [
OK ]
Started SSH Key Generation [
OK ]
Starting Permit User
Sessions...
Starting
xinetd.service...
Starting D-Bus System Message
Bus...
Starting Login
Service...
Started Console System Startup Logging [
OK ]
Started Permit User Sessions [
OK ]
Starting Serial Getty on
ttyO2...
Started Serial Getty on ttyO2 Started D-Bus System
Message Bus [ OK ]
xinetd[194]: Starting internet superserver: xinetd.
Started xinetd.service [
OK ]
Started Avahi mDNS/DNS-SD Stack [
OK ]
Started Login Service [
OK ]
[ 12.832061] smsc95xx v1.0.4
[ 13.045257] smsc95xx 1-2.1:1.0: eth0: register 'smsc95xx' at
usb-ehci-omap.0-2.1, smsc95xx USB 2.0 Ethernet, 82:57:8f:42:3a:50
[ 13.063842] usbcore: registered new interface driver smsc95xx
Starting Getty on
tty1...
Started Getty on tty1 [
OK ]
.---O---.
| | .-. o o
| | |-----.-----.-----.| | .----..-----.-----.
| | | __ | ---'| '--.| .-'| | |
| | | | | |--- || --'| | | ' | | | |
'---'---'--'--'--. |-----''----''--' '-----'-'-'-'
-' |
'---'
The Angstrom Distribution beagleboard ttyO2
Angstrom v2012.05 - Kernel 3.2.18
beagleboard login: root
Last login: Thu Jan 1 00:25:20 UTC 1970 on ttyO2
root@beagleboard:~# dmesg > ~/dmesg_out
root@beagleboard:~# [ 65.168518] usb 1-2.5: USB disconnect, device number
5
[ 66.689025] usb 1-2.5: new low-speed USB device number 6 using ehci-omap
[ 66.818786] usb 1-2.5: New USB device found, idVendor=093a,
idProduct=2510
[ 66.826293] usb 1-2.5: New USB device strings: Mfr=1, Product=2,
SerialNumber=0
[ 66.834259] usb 1-2.5: Product: USB Optical Mouse
[ 66.839416] usb 1-2.5: Manufacturer: PixArt
[ 66.848297] input: PixArt USB Optical Mouse as
/devices/platform/usbhs-omap.0/ehci-omap.0/usb1/1-2/1-2.5/1-2.5:1.0/input/input4
[ 66.863098] generic-usb 0003:093A:2510.0004: input,hidraw2: USB HID
v1.11 Mouse [PixArt USB Optical Mouse] on usb-ehci-omap.0-2.5/input0
* - * Qodem 0.1.2 Capture Generated Sat, 30 Jun 2012 12:06:37 -0600 END * -
*
[vidal@ws008 ~]$
The following is the serial for gnome boot on the the serial port.
[vidal@ws008 ~]$ cat gnome.txt
* - * Qodem 0.1.2 Capture Generated Sat, 30 Jun 2012 12:29:52 -0600 BEGIN *
- *
U-Boot SPL 2011.12-dirty (Jun 29 2012 - 23:53:16)
Texas Instruments Revision detection unimplemented
OMAP SD/MMC: 0
timed out in wait_for_bb: I2C_STAT=1000
reading u-boot.img
reading u-boot.img
U-Boot 2011.12-dirty (Jun 29 2012 - 23:53:16)
OMAP3630/3730-GP ES1.2, CPU-OPP2, L3-165MHz, Max CPU Clock 1 Ghz
OMAP3 Beagle board + LPDDR/NAND
I2C: ready
DRAM: 512 MiB
NAND: 0 MiB
MMC: OMAP SD/MMC: 0
*** Warning - readenv() failed, using default environment
In: serial
Out: serial
Err: serial
Beagle xM Rev C
No EEPROM on expansion board
No EEPROM on expansion board
Die ID #158000029ff800000160a7450b02602d
Net: Net Initialization Skipped
No ethernet found.
Hit any key to stop autoboot: 2 1 0
The user button is currently NOT pressed.
SD/MMC found on device 0
reading uEnv.txt
130 bytes read
Loaded environment from uEnv.txt
Importing environment from mmc ...
Loading file "/boot/uImage" from mmc device 0:2 xxa2
4385648 bytes read
Booting from mmc ...
## Booting kernel from Legacy Image at 80200000 ...
Image Name: Angstrom/3.2.18/beagleboard
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 4385584 Bytes = 4.2 MiB
Load Address: 80008000
Entry Point: 80008000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 3.2.18 (vi...@ws008.swbell.net) (gcc version
4.5.4 20120305 (prerelease) (GCC) ) #1 Fri Jun 29 15:35:31 MDT 2012
[ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7),
cr=10c5387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing
instruction cache
[ 0.000000] Machine: OMAP3 Beagle Board
[ 0.000000] Beagle expansionboard: none
[ 0.000000] Beagle second expansionboard: none
[ 0.000000] Reserving 16777216 bytes SDRAM for VRAM
[ 0.000000] Memory policy: ECC disabled, Data cache writeback
[ 0.000000] OMAP3630 ES1.2 (l2cache iva sgx neon isp 192mhz_clk )
[ 0.000000] Clocking rate (Crystal/Core/MPU): 26.0/400/600 MHz
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on.
Total pages: 124416
[ 0.000000] Kernel command line: console=tty0 console=ttyO2,115200n8
consoleblank=0 mpurate=auto buddy=none buddy2=none camera=none vram=16M
omapfb.mode=dvi:hd720 omapfb.vram=0:8M,1:4M,2:4M omapdss.def_disp=dvi
root=/dev/mmcblk0p2 ro rootfstype=ext4 rootwait
[ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144
bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072
bytes)
[ 0.000000] allocated 2097152 bytes of page_cgroup
[ 0.000000] please try 'cgroup_disable=memory' option if you don't want
memory cgroups
[ 0.000000] Memory: 490MB = 490MB total
[ 0.000000] Memory: 486344k/486344k available, 37944k reserved, 0K
highmem
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] vmalloc : 0xe0800000 - 0xf8000000 ( 376 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xe0000000 ( 512 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000] .text : 0xc0008000 - 0xc0741cec (7400 kB)
[ 0.000000] .init : 0xc0742000 - 0xc0788000 ( 280 kB)
[ 0.000000] .data : 0xc0788000 - 0xc07e2710 ( 362 kB)
[ 0.000000] .bss : 0xc07e2734 - 0xc089f854 ( 757 kB)
[ 0.000000] SLUB: Genslabs=11, HWalign=64, Order=0-3, MinObjects=0,
CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:410 nr_irqs:410 410
[ 0.000000] IRQ: Found an INTC at 0xfa200000 (revision 4.0) with 96
interrupts
[ 0.000000] Total of 96 interrupts on 1 active controller
[ 0.000000] OMAP clockevent source: GPTIMER12 at 32768 Hz
[ 0.000000] sched_clock: 32 bits at 32kHz, resolution 30517ns, wraps
every 131071999ms
[ 0.000000] Console: colour dummy device 80x30
[ 0.000000] console [tty0] enabled
[ 0.000610] Calibrating delay loop... 506.27 BogoMIPS (lpj=1978368)
[ 0.039794] pid_max: default: 32768 minimum: 301
[ 0.040039] Security Framework initialized
[ 0.040100] AppArmor: AppArmor initialized
[ 0.040344] Mount-cache hash table entries: 512
[ 0.040771] Initializing cgroup subsys cpuacct
[ 0.040802] Initializing cgroup subsys memory
[ 0.040863] Initializing cgroup subsys devices
[ 0.040893] Initializing cgroup subsys freezer
[ 0.040924] Initializing cgroup subsys blkio
[ 0.040954] Initializing cgroup subsys perf_event
[ 0.041046] CPU: Testing write buffer coherency: ok
[ 0.042114] devtmpfs: initialized
[ 0.045745] print_constraints: dummy:
[ 0.046020] NET: Registered protocol family 16
[ 0.046203] GPMC revision 5.0
[ 0.047668] OMAP GPIO hardware version 2.5
[ 0.048980] omap_mux_init: Add partition: #1: core, flags: 0
[ 0.050292] OMAP3 Beagle Rev: xM C
[ 0.053375] Reprogramming SDRC clock to 400000000 Hz
[ 0.053436] dpll3_m2_clk rate change failed: -22
[ 0.055267] Found NAND on CS0
[ 0.055297] Registering NAND on CS0
[ 0.055633] Unable to get DVI reset GPIO
[ 0.055786] hw-breakpoint: debug architecture 0x4 unsupported.
[ 0.059295] omap-mcbsp.2: alias fck already exists
[ 0.059509] omap-mcbsp.3: alias fck already exists
[ 0.060699] OMAP DMA hardware revision 5.0
[ 0.067535] bio: create slab <bio-0> at 0
[ 0.068786] SCSI subsystem initialized
[ 0.069976] usbcore: registered new interface driver usbfs
[ 0.070129] usbcore: registered new interface driver hub
[ 0.070312] usbcore: registered new device driver usb
[ 0.071075] omap_i2c omap_i2c.1: bus 1 rev1.4.0 at 2600 kHz
[ 0.073486] twl4030: PIH (irq 7) chaining IRQs 368..375
[ 0.073577] twl4030: power (irq 373) chaining IRQs 376..383
[ 0.074066] twl4030: gpio (irq 368) chaining IRQs 384..401
[ 0.074432] _omap_mux_init_gpio: Could not set gpio192
[ 0.077209] print_constraints: VUSB1V5: 1500 mV normal standby
[ 0.077636] print_constraints: VUSB1V8: 1800 mV normal standby
[ 0.078033] print_constraints: VUSB3V1: 3100 mV normal standby
[ 0.079711] twl4030_usb twl4030_usb: Initialized TWL4030 USB module
[ 0.080474] print_constraints: VMMC1: 1850 <--> 3150 mV at 3150 mV
normal standby
[ 0.080932] print_constraints: VDAC: 1800 mV normal standby
[ 0.081329] print_constraints: VAUX2_4030: 1800 mV normal
[ 0.081756] print_constraints: VDVI: 1800 mV normal standby
[ 0.082244] print_constraints: VSIM: 1800 <--> 3000 mV at 1800 mV normal
standby
[ 0.082580] omap_i2c omap_i2c.2: bus 2 rev1.4.0 at 400 kHz
[ 0.092895] omap_i2c omap_i2c.3: bus 3 rev1.4.0 at 100 kHz
[ 0.094024] NetLabel: Initializing
[ 0.094055] NetLabel: domain hash size = 128
[ 0.094085] NetLabel: protocols = UNLABELED CIPSOv4
[ 0.094146] NetLabel: unlabeled traffic allowed by default
[ 0.094177] Switching to clocksource 32k_counter
[ 0.107482] AppArmor: AppArmor Filesystem Enabled
[ 0.119476] musb-hdrc: version 6.0, ?dma?, otg (peripheral+host)
[ 0.124603] musb-hdrc musb-hdrc: USB OTG mode controller at fa0ab000
using DMA, IRQ 92
[ 0.124969] NET: Registered protocol family 2
[ 0.125274] IP route cache hash table entries: 4096 (order: 2, 16384
bytes)
[ 0.126098] TCP established hash table entries: 16384 (order: 5, 131072
bytes)
[ 0.126495] TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.126708] TCP: Hash tables configured (established 16384 bind 16384)
[ 0.126739] TCP reno registered
[ 0.126770] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.126800] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.127136] NET: Registered protocol family 1
[ 0.127563] RPC: Registered named UNIX socket transport module.
[ 0.127593] RPC: Registered udp transport module.
[ 0.127624] RPC: Registered tcp transport module.
[ 0.127655] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.127929] omap_dsp_init: 600000 bytes @ 9ea00000
[ 0.129577] audit: initializing netlink socket (disabled)
[ 0.129638] type=2000 audit(0.140:1): initialized
[ 0.339111] VFS: Disk quotas dquot_6.5.2
[ 0.339477] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.342926] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[ 0.343017] fuse init (API version 7.17)
[ 0.345092] Btrfs loaded
[ 0.345153] msgmni has been set to 949
[ 0.346679] Block layer SCSI generic (bsg) driver version 0.4 loaded
(major 253)
[ 0.346832] io scheduler noop registered
[ 0.346862] io scheduler deadline registered
[ 0.346923] io scheduler cfq registered (default)
[ 0.347839] OMAP DSS rev 2.0
[ 0.350433] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 0.351684] omap_uart.0: ttyO0 at MMIO 0x4806a000 (irq = 72) is a OMAP
UART0
[ 0.351989] omap_uart.1: ttyO1 at MMIO 0x4806c000 (irq = 73) is a OMAP
UART1
[ 0.352386] omap_uart.2: ttyO2 at MMIO 0x49020000 (irq = 74) is a OMAP
UART2
[ 1.081329] console [ttyO2] enabled
[ 1.085327] omap_uart.3: ttyO3 at MMIO 0x49042000 (irq = 80) is a OMAP
UART3
[ 1.093261] [drm] Initialized drm 1.1.0 20060810
[ 1.105773] brd: module loaded
[ 1.113128] loop: module loaded
[ 1.117797] twl4030_madc twl4030_madc: clk disabled, enabling
[ 1.125305] omap2-nand driver initializing
[ 1.130004] No NAND device found
[ 1.133636] No NAND device found
[ 1.137207] OneNAND driver initializing
[ 1.141937] usbcore: registered new interface driver cdc_ether
[ 1.148132] usbcore: registered new interface driver rndis_host
[ 1.154418] cdc_ncm: 04-Aug-2011
[ 1.157897] usbcore: registered new interface driver cdc_ncm
[ 1.164245] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 3.180236] ehci-omap ehci-omap.0: OMAP-EHCI Host Controller
[ 3.186523] ehci-omap ehci-omap.0: new USB bus registered, assigned bus
number 1
[ 3.194458] ehci-omap ehci-omap.0: irq 77, io mem 0x48064800
[ 3.211547] ehci-omap ehci-omap.0: USB 2.0 started, EHCI 1.00
[ 3.217681] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 3.224822] usb usb1: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 3.232452] usb usb1: Product: OMAP-EHCI Host Controller
[ 3.238037] usb usb1: Manufacturer: Linux 3.2.18 ehci_hcd
[ 3.243713] usb usb1: SerialNumber: ehci-omap.0
[ 3.249176] hub 1-0:1.0: USB hub found
[ 3.253173] hub 1-0:1.0: 3 ports detected
[ 3.281860] Initializing USB Mass Storage driver...
[ 3.287109] usbcore: registered new interface driver usb-storage
[ 3.293457] USB Mass Storage support registered.
[ 3.298431] usbcore: registered new interface driver libusual
[ 3.304626] udc: OMAP UDC driver, version: 4 October 2004 (iso) (dma)
[ 3.311859] mousedev: PS/2 mouse device common for all mice
[ 3.319183] input: twl4030_pwrbutton as
/devices/platform/omap/omap_i2c.1/i2c-1/1-0049/twl4030_pwrbutton/input/input0
[ 3.330993] i2c /dev entries driver
[ 3.335205] Linux media interface: v0.10
[ 3.339508] lirc_dev: IR Remote Control driver registered, major 249
[ 3.346282] Driver for 1-wire Dallas network protocol.
[ 3.352447] OMAP Watchdog Timer Rev 0x31: initial timeout 60 sec
[ 3.359161] twl4030_wdt twl4030_wdt: Failed to register misc device
[ 3.365783] twl4030_wdt: probe of twl4030_wdt failed with error -16
[ 3.373413] device-mapper: ioctl: 4.22.0-ioctl (2011-10-19) initialised:
dm-de...@redhat.com
[ 3.382781] cpuidle: using governor ladder
[ 3.387084] cpuidle: using governor menu
[ 3.391265] sdhci: Secure Digital Host Controller Interface driver
[ 3.397705] sdhci: Copyright(c) Pierre Ossman
[ 3.578796] usb 1-2: new high-speed USB device number 2 using ehci-omap
[ 3.619781] omap_hsmmc: probe of omap_hsmmc.1 failed with error -16
[ 3.629425] usbcore: registered new interface driver usbhid
[ 3.635284] usbhid: USB HID core driver
[ 3.639312] oprofile: hardware counters not available
[ 3.644622] oprofile: using timer interrupt.
[ 3.649841] TCP cubic registered
[ 3.654052] NET: Registered protocol family 10
[ 3.660308] NET: Registered protocol family 17
[ 3.665161] Registering the dns_resolver key type
[ 3.670166] VFP support v0.3: implementor 41 architecture 3 part 30
variant c rev 3
[ 3.678222] ThumbEE CPU extension supported.
[ 3.682708] Registering SWP/SWPB emulation handler
[ 3.691467] sr_init: No PMIC hook to init smartreflex
[ 3.696990] smartreflex smartreflex.0: omap_sr_probe: SmartReflex driver
initialized
[ 3.705230] smartreflex smartreflex.1: omap_sr_probe: SmartReflex driver
initialized
[ 3.713439] SmartReflex Class3 initialized
[ 3.721130] clock: disabling unused clocks to save power
[ 3.727569] registered taskstats version 1
[ 3.782623] usb 1-2: New USB device found, idVendor=0424, idProduct=9514
[ 3.789672] usb 1-2: New USB device strings: Mfr=0, Product=0,
SerialNumber=0
[ 3.797973] hub 1-2:1.0: USB hub found
[ 3.817108] Console: switching to colour frame buffer device 160x45
[ 3.838073] hub 1-2:1.0: 5 ports detected
[ 3.845886] regulator_init_complete: VDAC: incomplete constraints,
leaving on
[ 3.853668] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[ 3.861389] Waiting for root device /dev/mmcblk0p2...
[ 4.004943] mmc0: host does not support reading read-only switch.
assuming write-enable.
[ 4.016174] mmc0: new high speed SDHC card at address 1234
[ 4.022521] mmcblk0: mmc0:1234 SA08G 7.41 GiB
[ 4.029693] mmcblk0: p1 p2
[ 4.095581] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data
mode. Opts: (null)
[ 4.104370] VFS: Mounted root (ext4 filesystem) readonly on device 179:2.
[ 4.114654] devtmpfs: mounted
[ 4.123046] Freeing init memory: 280K
[ 4.149414] usb 1-2.1: new high-speed USB device number 3 using ehci-omap
[ 4.274810] usb 1-2.1: New USB device found, idVendor=0424,
idProduct=ec00
[ 4.287048] usb 1-2.1: New USB device strings: Mfr=0, Product=0,
SerialNumber=0
[ 4.383819] usb 1-2.3: new low-speed USB device number 4 using ehci-omap
Welcome to Linux!
[ 4.517303] usb 1-2.3: New USB device found, idVendor=0a81,
idProduct=0101
[ 4.529510] usb 1-2.3: New USB device strings: Mfr=1, Product=2,
SerialNumber=0
[ 4.542083] usb 1-2.3: Product: USB Keyboard
[ 4.551361] usb 1-2.3: Manufacturer: CHESEN
[ 4.567779] input: CHESEN USB Keyboard as
/devices/platform/usbhs-omap.0/ehci-omap.0/usb1/1-2/1-2.3/1-2.3:1.0/input/input1
[ 4.588073] generic-usb 0003:0A81:0101.0001: input,hidraw0: USB HID
v1.10 Keyboard [CHESEN USB Keyboard] on usb-ehci-omap.0-2.3/input0
[ 4.614105] input: CHESEN USB Keyboard as
/devices/platform/usbhs-omap.0/ehci-omap.0/usb1/1-2/1-2.3/1-2.3:1.1/input/input2
[ 4.634185] generic-usb 0003:0A81:0101.0002: input,hidraw1: USB HID
v1.10 Device [CHESEN USB Keyboard] on usb-ehci-omap.0-2.3/input1
[ 4.735290] usb 1-2.5: new low-speed USB device number 5 using ehci-omap
[ 4.864532] usb 1-2.5: New USB device found, idVendor=093a,
idProduct=2510
[ 4.877593] usb 1-2.5: New USB device strings: Mfr=1, Product=2,
SerialNumber=0
[ 4.890960] usb 1-2.5: Product: USB Optical Mouse
[ 4.901519] usb 1-2.5: Manufacturer: PixArt
[ 4.916259] input: PixArt USB Optical Mouse as
/devices/platform/usbhs-omap.0/ehci-omap.0/usb1/1-2/1-2.5/1-2.5:1.0/input/input3
[ 4.935791] generic-usb 0003:093A:2510.0003: input,hidraw2: USB HID
v1.11 Mouse [PixArt USB Optical Mouse] on usb-ehci-omap.0-2.5/input0
Started Apply Kernel Variables [
OK ]
Started Load Kernel Modules [
OK ]
Starting Debug File
System...
Started Set Up Additional Binary Formats [
OK ]
Started Huge Pages File System [
OK ]
Starting POSIX Message Queue File
System...
Starting FUSE Control File
System...
Started Configuration File System [
OK ]
Starting Temporary
Directory...
Starting File System Check on Root
Device...
Starting Remount API
VFS...
Starting udev Coldplug all
Devices...
Starting udev Kernel Device
Manager...
Starting Journal
Service...
Started Journal Service [
OK ]
Started Debug File System [
OK ]
Started POSIX Message Qu[ 5.373413] request_module: runaway loop
modprobe binfmt-0000
eue File System [ OK ]
Started FUSE Control File System [
OK ]
Started Temporary Directory [
OK ]
Started Remount API VFS [
OK ]
[ 5.423522] udevd[140]: starting version 182
Started udev Kernel Device Manager [
OK ]
Started File System Check on Root Device [
OK ]
Starting Remount Root
FS...
[ 5.581542] EXT4-fs (mmcblk0p2): re-mounted. Opts:
user_xattr,acl,barrier=1,data=ordered
Started Remount Root FS [
OK ]
Starting Load Random
Seed...
Starting Recreate Volatile Files and
Directories...
Started Machine ID first boot configure [
OK ]
Starting Run pending
postinsts...
Failed to start Load Random Seed
[FAILED]
See 'systemctl status systemd-random-seed-load.service' for
details.
Started udev Coldplug all Devices [
OK ]
Failed to start Recreate Volatile Files and Directories
[FAILED]
See 'systemctl status systemd-tmpfiles-setup.service' for
details.
[ 6.009002] request_module: runaway loop modprobe binfmt-0000
Failed to start Run pending postinsts
[FAILED]
See 'systemctl status run-postinsts.service' for
details.
Dependency failed. Aborted start of Login Service [
ABORT]
Dependency failed. Aborted start of D-Bus System Message Bus [
ABORT]
Dependency failed. Aborted start of Connection service [
ABORT]
Starting Console System Startup
Logging...
Starting SSH Key
Generation...
Started SSH Key Generation [
OK ]
Starting Permit User
Sessions...
Starting Timestamping
service...
Started Timestamping service [
OK ]
Started Permit User Sessions [
OK ]
[ 6.302795] request_module: runaway loop modprobe binfmt-0000
[ 6.316131] request_module: runaway loop modprobe binfmt-0000
Failed to start Console System Startup Logging
[FAILED]
See 'systemctl status console-kit-log-system-start.service' for
details.
[ 6.409027] twl_rtc twl_rtc: Power up reset detected.
[ 6.425292] twl_rtc twl_rtc: Enabling TWL-RTC.
Starting Serial Getty on
ttyO2...
[ 6.501037] twl_rtc twl_rtc: rtc core: registered twl_rtc as rtc0
Started Serial Ge[ 6.731750] smsc95xx v1.0.4
[ 6.757019] request_module: runaway loop modprobe binfmt-0000
Stopping Serial Getty on
ttyO2...
Starting Serial Getty on
ttyO2...
Started Serial Getty on ttyO2 [
OK ]
[ 6.940002] smsc95xx 1-2.1:1.0: eth0: register 'smsc95xx' at
usb-ehci-omap.0-2.1, smsc95xx USB 2.0 Ethernet, de:46:36:f4:1e:6a
[ 6.958282] usbcore: registered new interface driver smsc95xx
Stopping Serial Getty on
ttyO2...
Starting Serial Getty on
ttyO2...
Started Serial Getty on ttyO2 [
OK ]
Starting Getty on
tty1...
Started Getty on tty1 [
OK ]
[ 65.152435] usb 1-2.5: USB disconnect, device number 5
[ 66.415100] usb 1-2.5: new low-speed USB device number 6 using ehci-omap
[ 66.544158] usb 1-2.5: New USB device found, idVendor=093a,
idProduct=2510
[ 66.551574] usb 1-2.5: New USB device strings: Mfr=1, Product=2,
SerialNumber=0
[ 66.559448] usb 1-2.5: Product: USB Optical Mouse
[ 66.564483] usb 1-2.5: Manufacturer: PixArt
[ 66.574462] input: PixArt USB Optical Mouse as
/devices/platform/usbhs-omap.0/ehci-omap.0/usb1/1-2/1-2.5/1-2.5:1.0/input/input4
[ 66.588531] generic-usb 0003:093A:2510.0004: input,hidraw2: USB HID
v1.11 Mouse [PixArt USB Optical Mouse] on usb-ehci-omap.0-2.5/input0
* - * Qodem 0.1.2 Capture Generated Sat, 30 Jun 2012 12:32:11 -0600 END * -
*
[vidal@ws008 ~]$
Any help will be appeaciated.
Thanks
_______________________________________________
Angstrom-distro-devel mailing list
Angstrom-distro-devel@linuxtogo.org
http://lists.linuxtogo.org/cgi-bin/mailman/listinfo/angstrom-distro-devel
