Op 30 jul. 2012, om 13:25 heeft Peter Müller <p.mueller.nine...@gmail.com> het volgende geschreven:
> Hi Guys, > > i've build the Angstrom-Distribution for my Cubox (www.solid-run.com) > according to the Wiki (http://www.solid-run.com/mw/index.php/Angstrom). > After successful build using bitbake, i copied the image on an SD-Card and > tried to boot up the kernel. > > The U-Boot loader reads the image and tries to start the kernel. > Now (while booting) the System crashes with an "undefined Instruction" (see > log). What might be happening is that the kernel isn't turning on some coprocessor features. Can you post your bitbake build banner that is show at the start? Somehow NEON instructions might have crept in. regards, Koen > > CuBox>> setenv bootargs 'console=ttyS0,115200n8 vmalloc=384M rootdelay=10 > root=/dev/sda1 rw >> video=dovefb:lcd0:1920x1080-32@60-edid clcd.lcd0_enable=1 > clcd.lcd1_enable=0 usb0Mode=host usb1Mode=host' > CuBox>> usb > USB is stopped. Please issue 'usb start' first. > CuBox>> usb start > (Re)start USB... > USB: Register 10011 NbrPorts 1 > USB EHCI 1.00 > scanning bus for devices... 2 USB Device(s) found > Waiting for storage device(s) to settle before scanning... > scanning bus for storage devices... 1 Storage Device(s) found > CuBox>> ext2load usb 0:1 0x00200000 /boot/uImage > Loading file "/boot/uImage" from usb device 0:1 (usbda1) > 3396040 bytes read > CuBox>> bootm > ## Booting kernel from Legacy Image at 00200000 ... > Image Name: Angstrom/3.4-rc6/cubox > Created: 2012-06-09 11:35:53 UTC > Image Type: ARM Linux Kernel Image (uncompressed) > Data Size: 3395976 Bytes = 3.2 MB > Load Address: c0008000 > Entry Point: c0008000 > Verifying Checksum ... OK > Loading Kernel Image ... OK > OK > > Starting kernel ... > > undefined instruction > pc : [<f0000004>] lr : [<00635ffc>] > sp : 005ffe00 ip : 000008e0 fp : c0008000 > r10: 005fff98 r9 : 00000f41 r8 : 005fffcc > r7 : 006b304c r6 : 00700a68 r5 : 00000154 r4 : 00000000 > r3 : 00000000 r2 : 00000100 r1 : 00000f41 r0 : 00000000 > Flags: nZCv IRQs off FIQs off Mode SVC_32 > Resetting CPU ... > > CuBox > ** LOADER ** > > > U-Boot 2009.08 (Jan 15 2012 - 00:43:32) Marvell version: 5.4.4 NQ > > BootRom: > Version on chip: 2.33 > Status: OK > Retries #: 0 > Board: CuBox > SoC: 88AP510 (A1) > CPU: Marvell Sheeva (Rev 5) > CPU @ 800Mhz, L2 @ 400Mhz > DDR3 @ 400Mhz, TClock @ 166Mhz > PEX 0: interface detected no Link. > PEX 1: interface detected no Link. > DRAM: 1 GB > CS 0: base 0x00000000 size 512 MB > CS 1: base 0x20000000 size 512 MB > Addresses 12M - 0M are saved for the U-Boot usage. > SF: Detected M25P32 with page size 64 kB, total 4 MB > > Streaming disabled > L2 Cache Prefetch disabled > L2 Cache ECC disabled > Modifying CPU/CORE/DDR power rails to 1.0(-2.5%) / 1.0(-5%) / 1.5(-5%) > USB 0: Host Mode > USB 1: Host Mode > Setting VPU power OFF. > Setting GPU power ON. > MMC: MV_SDHCI: 0, MV_SDHCI: 1 > Net: egiga0 [PRIME] > Hit any key to stop autoboot: 0 > Post at solid-run Forum: > http://www.solid-run.com/phpbb/viewtopic.php?f=11&t=621 > > Can anybody tell how to fix this issue? > > > Best regards > PeterM > _______________________________________________ > Angstrom-distro-devel mailing list > Angstrom-distro-devel@linuxtogo.org > http://lists.linuxtogo.org/cgi-bin/mailman/listinfo/angstrom-distro-devel _______________________________________________ Angstrom-distro-devel mailing list Angstrom-distro-devel@linuxtogo.org http://lists.linuxtogo.org/cgi-bin/mailman/listinfo/angstrom-distro-devel
