Hi, I compiled a kernel for my beaglebone ( not the black one ), I would like to install this kernel to my SD card with angstrom ( Angstrom-Cloud9-IDE-GNOME-eglibc-ipk-v2012.12-beaglebone-2013.05.24.img.xz )
I discovered that install_kernel.sh doesn't work for the moment. So I would like to know where I've to move the files, to install the new kernel. ( those informations will be used later to modify the install_kernel.sh ) For the moment, I've a folder deploy with those files : 3.8.13-bone20.config 3.8.13-bone20-dtbs.tar.gz 3.8.13-bone20-firmware.tar.gz 3.8.13-bone20-modules.tar.gz 3.8.13-bone20.zImage and one folder : disk Thx you very much ! Micka, ---------- Forwarded message ---------- From: Robert Nelson <robertcnel...@gmail.com> Date: Thu, May 30, 2013 at 10:03 PM Subject: Re: install kernel to the sdcard => failed To: Micka <mickamus...@gmail.com> On Thu, May 30, 2013 at 2:55 PM, Micka <mickamus...@gmail.com> wrote: > Well, > > First I installed this image : > > xz -dkc > Angstrom-Cloud9-IDE-GNOME-eglibc-ipk-v2012.12-beaglebone-2013.05.24.img.xz > > /dev/sdb > > and just after I use your command : > ( sdb 1 : 4.88MB free AND sdb2: 2.18 GB ) > > sudo ./tools/install_kernel.sh > > I see... > fdisk -l: > Disk /dev/sda: 59.3 GB, 59268661248 bytes > Disk /dev/sdb: 15.9 GB, 15931539456 bytes > > lsblk: > NAME MAJ:MIN RM SIZE RO TYPE MOUNTPOINT > sda 8:0 0 55.2G 0 disk > ├─sda1 8:1 0 50.4G 0 part / > ├─sda2 8:2 0 1K 0 part > └─sda5 8:5 0 4.8G 0 part [SWAP] > sdb 8:16 1 14.9G 0 disk > ├─sdb1 8:17 1 70.6M 0 part /media/kernelbuild/BEAGLE_BONE > └─sdb2 8:18 1 3.3G 0 part /media/kernelbuild/Angstrom-Cloud9- > > > Unmounting Partitions > ----------------------------- > Starting Partition Search > ----------------------------- > Trying > Partition: [] trying: [vfat], [ext4] > Trying /dev/sdb1 > Partition: [/dev/sdb1] trying: [vfat], [ext4] > Partition: [vfat] > Installing 3.8.13-bone20 to /dev/sdb1 > Image Name: 3.8.13-bone20 > Created: Thu May 30 21:54:25 2013 > Image Type: ARM Linux Kernel Image (uncompressed) > Data Size: 3245096 Bytes = 3169.04 kB = 3.09 MB > Load Address: 80008000 > Entry Point: 80008000 > `/home/kernelbuild/beaglebone/linux-dev/deploy/3.8.13-bone20.zImage' -> > `/home/kernelbuild/beaglebone/linux-dev/deploy/disk/zImage' > cp: writing `/home/kernelbuild/beaglebone/linux-dev/deploy/disk/zImage': No > space left on device > cp: failed to extend > `/home/kernelbuild/beaglebone/linux-dev/deploy/disk/zImage': No space left > on device > > > > What is wrong ? How can I correct that ? Ahh, now i see what your doing.. Well... Angstrom loads everything from the /dev/sdb2 now, and fills up /dev/sdb1 with drivers/etc... So it looks i need to 'detect' an angstrom install and not copy the zImage/etc over.. It'll probably be a simple patch to ./tools/install-kernel.sh, probally take a good hour of hacking time tomorrow.. I'm going to probably use the "BEAGLE_BONE" name as a trigger, ( i always call it boot).. Regards, -- Robert Nelson http://www.rcn-ee.com/ _______________________________________________ Angstrom-distro-users mailing list Angstrom-distro-users@linuxtogo.org http://lists.linuxtogo.org/cgi-bin/mailman/listinfo/angstrom-distro-users
