I am getting Apple II+es, IIEs and IIGSes ready for students to use in their homes. Looking for preschool and lower elementary educational freeware sites. I want to avoid copyright infringements and licensing problems and am not ready, yet, to write my own.
----- Original Message ----- From: "Antonio Rodríguez" <[EMAIL PROTECTED]> To: "Apple2list" <[EMAIL PROTECTED]> Sent: Sunday, September 19, 2004 7:06 PM Subject: Re: DOS Dump Issues > Probably some data is becoming lost in the transfer. I'd try these things: > > 1) Init the SSC with the ^A 6B ^A 0D ^A 0P to make sure you're in 8 bit, 1 stop, > no parity mode (of course, ^A means the Control-A command escape character). > > 2) Try to enable CTS and/or DSR handshaking. It won't hurt if you do, and it can > solve the problem. If the PC is unable to send the data after enabling one of > these, disable it again. At this point, I'm not sure of what handshaking signals > are provided by the SSC, bit it *does* provide hardware handshaking. > > 3) If nothing works, try to replace the cable with a known-good one (one that > connects not only the data lines, but also the handshaking ones) and repeat the > previous steps. > > Hope this helps! > > Greetings, > > Antonio Rodríguez (Grijan) > <ftp://grijan.cjb.net:21000/> > > [EMAIL PROTECTED] ha escrito: > > > I am having some trouble getting a dump of DOS onto my apple2. I have an > > enhanced //e with a SSC, disk controller, and 80-col/64K expansion. I have > > successfully gotten the serial link going and it appears as tho I can transfer > > the DOS33.DMP file successfully into memory. However, when it gets to the > > end of the dump, the apple remains in the monitor. The final screen has > > the last bits of the input and: > > > > 9E02- A=BF X=02 Y=A0 P=B0 S=F0 > > > > My com1 setup is as follows: > > > > Status for device COM1: > > ----------------------- > > Baud: 300 > > Parity: None > > Data Bits: 8 > > Stop Bits: 1 > > Timeout: ON > > XON/XOFF: OFF > > CTS handshaking: OFF > > DSR handshaking: OFF > > DSR sensitivity: OFF > > DTR circuit: ON > > RTS circuit: ON > > > > I use Alt-A 6B to set up the SSC. > > > > If you want to see the dump file, let me know and I can send it to you. > > The documentation that came with the dump file insisted that the apple > > would be back at the prompt with DOS 3.3 running and I just need to format > > a disk. There is no troubleshooting section. I appreciate any feedback. > > Thanks. > > > > Jackman. > > > > -- > Apple2list is sponsored by <http://lowendmac.com/> and... > > / Buy books, CDs, videos, and more from Amazon.com \ > / <http://www.amazon.com/exec/obidos/redirect-home/lowendmac> \ > > Support Low End Mac <http://lowendmac.com/lists/support.html> > > Apple2list info: <http://lowendmac.com/lists/apple2.html> > --> AOL users, remove "mailto:"; > Send list messages to: <mailto:[EMAIL PROTECTED]> > To unsubscribe, email: <mailto:[EMAIL PROTECTED]> > For digest mode, email: <mailto:[EMAIL PROTECTED]> > Subscription questions: <mailto:[EMAIL PROTECTED]> > Archive: <http://www.mail-archive.com/apple2list%40mail.maclaunch.com/> > > Using a Mac? Free email & more at Applelinks! http://www.applelinks.com > -- Apple2list is sponsored by <http://lowendmac.com/> and... / Buy books, CDs, videos, and more from Amazon.com \ / <http://www.amazon.com/exec/obidos/redirect-home/lowendmac> \ Support Low End Mac <http://lowendmac.com/lists/support.html> Apple2list info: <http://lowendmac.com/lists/apple2.html> --> AOL users, remove "mailto:"; Send list messages to: <mailto:[EMAIL PROTECTED]> To unsubscribe, email: <mailto:[EMAIL PROTECTED]> For digest mode, email: <mailto:[EMAIL PROTECTED]> Subscription questions: <mailto:[EMAIL PROTECTED]> Archive: <http://www.mail-archive.com/apple2list%40mail.maclaunch.com/> Using a Mac? Free email & more at Applelinks! http://www.applelinks.com
