Are you using FRAMEBUFFER ? If you are, disable it, it probably should be fine without FB.
Quoting "Lin, Zihui" <[EMAIL PROTECTED]>: > Hi folks, > > I'm running ArchLinux on an R40e Thinkpad. > I have X running after 'startx', and then I switch to tty, lets say, > 'Ctrl + Alt + F1'. After type some command in the console, I switch back > to X, then I have problem. In such cases, my keyboard dies and the X > display garbles. Because I can't use the keyboard, the only thing that I > can do is to press the power button. > Same thing happens when I run the tuxracer. Whenever Tuxracer goes > full-screen, the key board and X dies. > I must have some mistakes when configuring my keyboard. Any one even > encountered this situation before? > > Zihui > > P.S. Here is my xorg.conf: > > Section "ServerLayout" > Identifier "X.org Configured" > Screen 0 "Screen0" 0 0 > InputDevice "Mouse0" "CorePointer" > InputDevice "Keyboard0" "CoreKeyboard" > EndSection > > Section "Files" > RgbPath "/usr/X11R6/lib/X11/rgb" > ModulePath "/usr/X11R6/lib/modules" > FontPath "/usr/X11R6/lib/X11/fonts/misc/" > FontPath "/usr/X11R6/lib/X11/fonts/TTF/" > FontPath "/usr/X11R6/lib/X11/fonts/Type1/" > FontPath "/usr/X11R6/lib/X11/fonts/75dpi/" > FontPath "/usr/X11R6/lib/X11/fonts/100dpi/" > FontPath "/usr/share/fonts/song" > EndSection > > Section "Module" > Load "extmod" > Load "glx" > Load "dri" > Load "dbe" > Load "record" > Load "xtrap" > Load "type1" > Load "freetype" > EndSection > > Section "InputDevice" > Identifier "Keyboard0" > Driver "kbd" > EndSection > > Section "InputDevice" > Identifier "Mouse0" > Driver "mouse" > Option "Protocol" "auto" > Option "ZAxisMapping" "4 5" > Option "Device" "/dev/psaux" > Option "Emulate3Buttons" "true" > Option "Emulate3Timeout" "70" > Option "SendCoreEvents" "true" > Option "EmulateWheel" "true" > Option "EmulateWheelButton" "2" > Option "EmulateWheelInertia" "10" > EndSection > > Section "InputDevice" > Identifier "USB Mouse" > Driver "mouse" > Option "Device" "/dev/input/mice" > Option "Protocol" "explorerps/2" > Option "ZAxisMapping" "4 5" > Option "Buttons" "5" > EndSection > > Section "Monitor" > Identifier "Monitor0" > VendorName "Monitor Vendor" > ModelName "Monitor Model" > HorizSync 28.0 - 96.0 > VertRefresh 50.0 - 75.0 > EndSection > > Section "Device" > Identifier "Card0" > Driver "ati" > VendorName "ATI Technologies Inc" > BoardName "Radeon IGP 340M" > BusID "PCI:1:5:0" > EndSection > > Section "Screen" > Identifier "Screen0" > Device "Card0" > Monitor "Monitor0" > DefaultColorDepth 24 > SubSection "Display" > Viewport 0 0 > Depth 1 > EndSubSection > SubSection "Display" > Viewport 0 0 > Depth 4 > EndSubSection > SubSection "Display" > Viewport 0 0 > Depth 8 > EndSubSection > SubSection "Display" > Viewport 0 0 > Depth 15 > EndSubSection > SubSection "Display" > Viewport 0 0 > Depth 16 > EndSubSection > SubSection "Display" > Depth 24 > #Modes "800x600" "640x480" > Modes "1024x768" "800x600" "640x480" > EndSubSection > EndSection > > _______________________________________________ > arch mailing list > [email protected] > http://www.archlinux.org/mailman/listinfo/arch > > ----------------------- http://www.cartucho.org ---------------------------------------------------------------- This message was sent using IMP, the Internet Messaging Program. _______________________________________________ arch mailing list [email protected] http://www.archlinux.org/mailman/listinfo/arch
