Hi, Thanks for the advice! I will try to recreate the scenario without doing too much damage and let you know what I learn.
I've got a solution that is working at the moment. My sincere thanks for your consideration of my problem. Kind regards. ============================================================ From: Guillermo Vaya <[EMAIL PROTECTED]> Date: 2005/11/16 Wed PM 05:10:19 EST To: General Discusson about Arch Linux <[email protected]> Subject: Re: [arch] 0.7.1 PCI problems I use one pci card that has the very same module and it works fine, also I have an onboard ethernet which uses the via-rhine. A couple of days ago I upgraded, and everything seemed to work fine until the reboot. After that, I was unable to use any of them (I just use one of them). Finally, I discovered that they have swapped places, the one that was eth0 is now eth1 and viceversa. It might not be what happened to you, but you should check it, just in case. Regards, Guillermo Vayá (aka Driadan) [EMAIL PROTECTED] wrote: >I've been able to work past these questions. There may need to be some better >descriptions written on how to enable ETH0. > >The souce compilation must have had something to do with changing compilers or >header files somewhere. I downloaded the lastest source (once I got the >ethernet up and going) and was able to compile. > >Kind regards. > >============================================================ >From: <[EMAIL PROTECTED]> >Date: 2005/11/12 Sat PM 01:34:01 EST >To: <[email protected]> >Subject: [arch] 0.7.1 PCI problems > >I'm probably in over my head here, but thought I would post my problem. > >I have 0.7, upgraded to current running fine on one PC. I'm reasonably >familiar with the scritps for configure Arch. > >On a different PC I thought I would put in 0.7.1 to offer any help I could to >testing. I'm stuck on a couple of issues. First of all, using 0.7.1 I'm >unable to find my on-board Ethernet. Following these basic directions: > >http://archlinux.org/pipermail/arch/2003-June/000274.html > >whereas in 0.7 I discover Ethernet, and enable using modprobe 8139too, I get >no card information really whatsoever in 0.7.1. There are a bunch of generic >entries, with non-prefetchable addresses, but very vague information. > >I've seen alot about mkinitrd, but I thought that was mostly for boot volumes >and so forth. Otherwise I can't find any information about other changes in >the boot process. > >I have a second issue with compiling ndiswrapper. This code compiles OK on >0.7, but failes with "incompatible type for argument 2 of pci_set_power_state". > >Can anyone offer some advice? > >Unfortunately I can't do much cut and paste to display better details since I >cannot connect the 0.7.1 distribution to the net. BTW, I went back to 0.7 on >the same PC and was moving right along, but thought it might be helpful to >figure out what was going on wht 0.7.1. > >Kind regards. > > >_______________________________________________ >arch mailing list >[email protected] >http://www.archlinux.org/mailman/listinfo/arch >============================================================ > > > >_______________________________________________ >arch mailing list >[email protected] >http://www.archlinux.org/mailman/listinfo/arch > > -- "I see connected people" - The seventh sense Registered Linux User #378439 <http://counter.li.org/> Willinux.net <http://www.willinux.net> - Pagina Williblog <http://blog.willinux.net> - Mi Blog personal _______________________________________________ arch mailing list [email protected] http://www.archlinux.org/mailman/listinfo/arch ============================================================ _______________________________________________ arch mailing list [email protected] http://www.archlinux.org/mailman/listinfo/arch
