Interestingly console input works in UKC but not in the install prompt. Possibly UKC still uses the serial console initialised by U-Boot and the Installer prompt is after OBSD takes over and re-initializes the serial port. Still investigating.
--Z-- Mizsei Zoltán írta 2023. nov.. 18, Szo-n 10:33 órakor: > I have extracted the DTB from linux, decompiled using DTC. The DTB > mentions both UARTs and FIQ-Debugger. Since they are mutually exclusive > (FIXME!), i have disabled FIQ and enabled the UART. > > i managed to land in the install prompt, but no input gets accepted: > > boot log: > >>> OpenBSD/arm64 BOOTAA64 1.18 > boot> stty com7 1500000 > boot> set tty com7 > switching console to com7 >>> OpenBSD/arm64 BOOTAA64 1.18 > boot> set device sd11a > boot> b > cannot open sd11a:/etc/random.seed: No such file or directory > booting sd11a:/bsd: 2861736+1091248+12711584+634544 > [233295+91+666048+260913]=0x13d5cf8 > Copyright (c) 1982, 1986, 1989, 1991, 1993 > The Regents of the University of California. All rights > reserved. > Copyright (c) 1995-2023 OpenBSD. All rights reserved. > https://www.OpenBSD.org > > OpenBSD 7.4 (RAMDISK) #2131: Sun Oct 8 13:35:40 MDT 2023 > dera...@arm64.openbsd.org:/usr/src/sys/arch/arm64/compile/RAMDISK > real mem = 2036940800 (1942MB) > avail mem = 1937518592 (1847MB) > random: boothowto does not indicate good seed > mainbus0 at root: Rockchip RK3566 EVB2 LP4X V10 Board > psci0 at mainbus0: PSCI 1.1, SMCCC 1.2, SYSTEM_SUSPEND > efi0 at mainbus0: UEFI 2.0.5 > cpu0 at mainbus0 mpidr 0: ARM Cortex-A55 r2p0 > cpu0: 32KB 64b/line 4-way L1 VIPT I-cache, 32KB 64b/line 4-way L1 > D-cache > cpu0: 512KB 64b/line 16-way L2 cache > cpu0: > DP,RDM,Atomic,CRC32,SHA2,SHA1,AES+PMULL,LRCPC,DPB,ASID16,PAN+ATS1E1,LO,HPDS,VH,HAFDBS,SBSS > scmi0 at mainbus0: SCMI 2.0 > "sdei" at mainbus0 not configured > "drm-logo" at mainbus0 not configured > "drm-cubic-lut" at mainbus0 not configured > "ramoops" at mainbus0 not configured > agintc0 at mainbus0 shift 4:4 nirq 352 nredist 4: "interrupt-controller" > agintcmsi0 at agintc0 > syscon0 at mainbus0: "syscon" > rkiovd0 at syscon0 > "reboot-mode" at syscon0 not configured > syscon1 at mainbus0: "syscon" > syscon2 at mainbus0: "syscon" > syscon3 at mainbus0: "syscon" > syscon4 at mainbus0: "syscon" > syscon5 at mainbus0: "syscon" > syscon6 at mainbus0: "syscon" > syscon7 at mainbus0: "syscon" > syscon8 at mainbus0: "syscon" > rkclock0 at mainbus0: PMUCRU > rkclock1 at mainbus0: CRU > rkclock_set_parent: 0x00000106 > rkclock_set_frequency(rkclock1, 262, 300000000) > rkclock_set_parent: 0x0000010b > rkclock_set_frequency(rkclock1, 267, 300000000) > rkclock_set_frequency(rkclock0, 43, 100000000) > rkclock_set_frequency(rkclock1, 3, 1000000000) > rkclock_set_frequency(rkclock1, 411, 500000000) > rkclock_set_frequency(rkclock1, 9, 333000000) > rkclock_set_frequency(rkclock1, 412, 250000000) > rk3568_set_pll: 1188000000 Hz > rkclock_set_frequency(rkclock1, 269, 150000000) > rkclock_set_frequency(rkclock1, 270, 100000000) > rkclock_set_frequency(rkclock1, 371, 500000000) > rkclock_set_frequency(rkclock1, 372, 400000000) > rkclock_set_frequency(rkclock1, 373, 150000000) > rkclock_set_frequency(rkclock1, 374, 100000000) > rkclock_set_frequency(rkclock1, 201, 300000000) > rkclock_set_frequency(rkclock1, 202, 150000000) > rkclock_set_frequency(rkclock1, 6, 1200000000) > rkclock_set_frequency(rkclock1, 126, 400000000) > rkclock_set_frequency(rkclock1, 127, 100000000) > rkclock_set_frequency(rkclock1, 61, 1188000000) > rkclock_set_frequency(rkclock1, 65, 1188000000) > rkclock_set_frequency(rkclock1, 69, 1188000000) > rkclock_set_frequency(rkclock1, 73, 1188000000) > rkclock_set_frequency(rkclock1, 77, 1188000000) > rkclock_set_frequency(rkclock1, 77, 1188000000) > rkclock_set_frequency(rkclock1, 85, 1188000000) > rkclock_set_frequency(rkclock1, 81, 1188000000) > rkclock_set_frequency(rkclock1, 93, 1188000000) > rkclock_set_frequency(rkclock1, 221, 500000000) > syscon9 at mainbus0: "power-management" > "power-controller" at syscon9 not configured > syscon10 at mainbus0: "qos" > syscon11 at mainbus0: "qos" > syscon12 at mainbus0: "qos" > syscon13 at mainbus0: "qos" > syscon14 at mainbus0: "qos" > syscon15 at mainbus0: "qos" > syscon16 at mainbus0: "qos" > syscon17 at mainbus0: "qos" > syscon18 at mainbus0: "qos" > syscon19 at mainbus0: "qos" > syscon20 at mainbus0: "qos" > syscon21 at mainbus0: "qos" > syscon22 at mainbus0: "qos" > syscon23 at mainbus0: "qos" > syscon24 at mainbus0: "qos" > syscon25 at mainbus0: "qos" > syscon26 at mainbus0: "qos" > syscon27 at mainbus0: "qos" > syscon28 at mainbus0: "qos" > syscon29 at mainbus0: "qos" > syscon30 at mainbus0: "qos" > syscon31 at mainbus0: "qos" > syscon32 at mainbus0: "qos" > syscon33 at mainbus0: "qos" > rkcomphy0 at mainbus0 > rkcomphy1 at mainbus0 > rkusbphy0 at mainbus0: phy 0 > rkusbphy1 at mainbus0: phy 1 > rkpinctrl0 at mainbus0: "pinctrl" > rkgpio0 at rkpinctrl0 > rkgpio1 at rkpinctrl0 > rkgpio2 at rkpinctrl0 > rkgpio3 at rkpinctrl0 > rkgpio4 at rkpinctrl0 > "ddr3-params" at mainbus0 not configured > "ddr4-params" at mainbus0 not configured > "lpddr3-params" at mainbus0 not configured > "lpddr4-params" at mainbus0 not configured > "lpddr4x-params" at mainbus0 not configured > "cpu0-opp-table" at mainbus0 not configured > "arm-pmu" at mainbus0 not configured > "cpuinfo" at mainbus0 not configured > "display-subsystem" at mainbus0 not configured > "firmware" at mainbus0 not configured > "rockchip-suspend" at mainbus0 not configured > "rockchip-system-monitor" at mainbus0 not configured > agtimer0 at mainbus0: 24000 kHz > "external-gmac1-clock" at mainbus0 not configured > "xpcs-gmac1-clock" at mainbus0 not configured > "i2s1-mclkin-rx" at mainbus0 not configured > "i2s1-mclkin-tx" at mainbus0 not configured > "i2s2-mclkin" at mainbus0 not configured > "i2s3-mclkin" at mainbus0 not configured > "mpll" at mainbus0 not configured > "xin24m" at mainbus0 not configured > "xin32k" at mainbus0 not configured > "scmi-shmem" at mainbus0 not configured > rkdwusb0 at mainbus0: "usbdrd" > xhci0 at rkdwusb0, xHCI 1.10 > usb0 at xhci0: USB revision 3.0 > uhub0 at usb0 configuration 1 interface 0 "Generic xHCI root hub" rev > 3.00/1.00 addr 1 > rkdwusb1 at mainbus0: "usbhost" > xhci1 at rkdwusb1, xHCI 1.10 > usb1 at xhci1: USB revision 3.0 > uhub1 at usb1 configuration 1 interface 0 "Generic xHCI root hub" rev > 3.00/1.00 addr 1 > "sram" at mainbus0 not configured > rkiic0 at mainbus0 > iic0 at rkiic0 > "atmel,24c02" at iic0 addr 0x50 not configured > "tcs,tcs4525" at iic0 addr 0x1c not configured > rkpmic0 at iic0 addr 0x20: RK809 > rkpmic0: can't read register 0xbb > rkpmic0: can't read register 0xbb > rkpmic0: can't write register 0xbb > rkpmic0: can't read register 0xbb > rkpmic0: can't read register 0xbe > rkpmic0: can't read register 0xbe > rkpmic0: can't write register 0xbe > rkpmic0: can't read register 0xc1 > rkpmic0: can't read register 0xc4 > rkpmic0: can't read register 0xc4 > rkpmic0: can't write register 0xc4 > rkpmic0: can't read register 0xc4 > rkpmic0: can't read register 0xcc > rkpmic0: can't read register 0xcc > rkpmic0: can't write register 0xcc > rkpmic0: can't read register 0xce > rkpmic0: can't read register 0xce > rkpmic0: can't write register 0xce > rkpmic0: can't read register 0xd0 > rkpmic0: can't read register 0xd0 > rkpmic0: can't write register 0xd0 > rkpmic0: can't read register 0xd2 > rkpmic0: can't read register 0xd2 > rkpmic0: can't write register 0xd2 > rkpmic0: can't read register 0xd4 > rkpmic0: can't read register 0xd4 > rkpmic0: can't write register 0xd4 > rkpmic0: can't read register 0xd6 > rkpmic0: can't read register 0xd6 > rkpmic0: can't write register 0xd6 > rkpmic0: can't read register 0xd6 > rkpmic0: can't read register 0xd6 > rkpmic0: can't read register 0xd6 > rkpmic0: can't read register 0xd8 > rkpmic0: can't read register 0xd8 > rkpmic0: can't write register 0xd8 > rkpmic0: can't read register 0xd8 > rkpmic0: can't read register 0xda > rkpmic0: can't read register 0xda > rkpmic0: can't write register 0xda > rkpmic0: can't read register 0xdc > rkpmic0: can't read register 0xdc > rkpmic0: can't write register 0xdc > rkpmic0: can't read register 0xde > rkpmic0: can't read register 0xde > rkpmic0: can't write register 0xde > rkpmic0: can't read register 0xde > rkpmic0: can't read register 0xde > "pvtm" at mainbus0 not configured > "npu" at mainbus0 not configured > "npu-opp-table" at mainbus0 not configured > "bus-npu-opp-table" at mainbus0 not configured > "iommu" at mainbus0 not configured > "gpu" at mainbus0 not configured > "opp-table2" at mainbus0 not configured > "pvtm" at mainbus0 not configured > "pvtm" at mainbus0 not configured > "vdpu" at mainbus0 not configured > "iommu" at mainbus0 not configured > "rk_rga" at mainbus0 not configured > "vepu" at mainbus0 not configured > "iommu" at mainbus0 not configured > "rkvenc" at mainbus0 not configured > "rkvenc-opp-table" at mainbus0 not configured > "iommu" at mainbus0 not configured > "rkvdec" at mainbus0 not configured > "rkvdec-opp-table" at mainbus0 not configured > "iommu" at mainbus0 not configured > "iommu" at mainbus0 not configured > "rkisp" at mainbus0 not configured > "iommu" at mainbus0 not configured > "rkisp-vir0" at mainbus0 not configured > "vop" at mainbus0 not configured > "iommu" at mainbus0 not configured > "hdmi" at mainbus0 not configured > "nocp-cpu" at mainbus0 not configured > "nocp-gpu-vpu-rga-venc" at mainbus0 not configured > "nocp-vdec" at mainbus0 not configured > "nocp-vi-usb-peri-pipe" at mainbus0 not configured > "nocp-vo" at mainbus0 not configured > "dmc-fsp" at mainbus0 not configured > "dmc-opp-table" at mainbus0 not configured > dwmmc0 at mainbus0: 50 MHz base clock > sdmmc0 at dwmmc0: 4-bit, sd high-speed, dma > "spi" at mainbus0 not configured > dwmshc0 at mainbus0 > dwmshc0: SDHC 4.20, 200 MHz base clock > sdmmc1 at dwmshc0: 8-bit, sd high-speed, mmc high-speed, dma > "nandc" at mainbus0 not configured > rkrng0 at mainbus0: ver 2 > "otp" at mainbus0 not configured > "i2s" at mainbus0 not configured > "dmac" at mainbus0 not configured > "dmac" at mainbus0 not configured > rkiic1 at mainbus0 > iic1 at rkiic1 > "goodix,gt1x" at iic1 addr 0x14 not configured > rkiic2 at mainbus0 > iic2 at rkiic2 > "ovti,ov5647" at iic2 addr 0x36 not configured > "galaxycore,gc8034" at iic2 addr 0x37 not configured > rkiic3 at mainbus0 > iic3 at rkiic3 > "timer" at mainbus0 not configured > "watchdog" at mainbus0 not configured > "spi" at mainbus0 not configured > com0 at mainbus0: dw16550, 64 byte fifo > com1 at mainbus0: dw16550, 64 byte fifo > com2 at mainbus0: dw16550, 64 byte fifo > com3 at mainbus0: dw16550, 64 byte fifo > com3: console > com4 at mainbus0: dw16550, 64 byte fifo > rkpwm0 at mainbus0rkclock_get_frequency(rkclock1, 346) > : no clock > rkpwm1 at mainbus0rkclock_get_frequency(rkclock1, 346) > : no clock > "tsadc" at mainbus0 not configured > "saradc" at mainbus0 not configured > "csi2-dphy-hw" at mainbus0 not configured > "csi2-dphy1" at mainbus0 not configured > "adc-keys" at mainbus0 not configured > "backlight" at mainbus0 not configured > "backlight1" at mainbus0 not configured > "dc-12v" at mainbus0 not configured > "hdmi-sound" at mainbus0 not configured > "leds" at mainbus0 not configured > "rk809-sound" at mainbus0 not configured > "spdif-sound" at mainbus0 not configured > "spdif-out" at mainbus0 not configured > "vcc3v3-sys" at mainbus0 not configured > "vcc5v0-sys" at mainbus0 not configured > "vcc5v0-usb" at mainbus0 not configured > "vcc5v0-host-regulator" at mainbus0 not configured > "vcc5v0-otg-regulator" at mainbus0 not configured > "vcc3v3-lcd0-n" at mainbus0 not configured > "vcc3v3-lcd1-n" at mainbus0 not configured > "sdio-pwrseq" at mainbus0 not configured > "wireless-wlan" at mainbus0 not configured > "wireless-bluetooth" at mainbus0 not configured > "test-power" at mainbus0 not configured > "vcc-camera-regulator" at mainbus0 not configured > "external-camera-clock" at mainbus0 not configured > "gpio-regulator" at mainbus0 not configured > "debug" at mainbus0 not configured > "cspmu" at mainbus0 not configured > "framebuffer" at mainbus0 not configured > rk3568_pmu_enable: 0x00000005 > bwfm0 at sdmmc0 function 1 > bwfm0: SoC interconnect SB not implemented > bwfm0: cannot attach chip > manufacturer 0x02d0, product 0xa9bf at sdmmc0 function 2 not configured > manufacturer 0x02d0, product 0xa9bf at sdmmc0 function 3 not configured > sdmmc1: can't enable card > uhub2 at uhub1 port 1 configuration 1 interface 0 "Terminus Technology > USB2.0 HUB" rev 2.00/1.00 addr 2 > umass0 at uhub2 port 1 configuration 1 interface 0 "Sony Storage Media" > rev 2.10/1.00 addr 3 > umass0: using SCSI over Bulk-Only > scsibus0 at umass0: 2 targets, initiator 0 > sd0 at scsibus0 targ 1 lun 0: <Sony, Storage Media, PMAP> removable > serial.054c09c2593A1D156A65 > sd0: 29637MB, 512 bytes/sector, 60698112 sectors > umass1 at uhub2 port 3 configuration 1 interface 0 "USB SanDisk > 3.2Gen1" rev 2.10/1.00 addr 4 > umass1: using SCSI over Bulk-Only > scsibus1 at umass1: 2 targets, initiator 0 > sd1 at scsibus1 targ 1 lun 0: <USB, SanDisk 3.2Gen1, 1.00> removable > serial.0781558381075e2a041c > sd1: 29340MB, 512 bytes/sector, 60088320 sectors > softraid0 at root > scsibus2 at softraid0: 256 targets > root on rd0a swap on rd0b dump on rd0b > rkpmic0: can't read RTC > WARNING: bad clock chip time > WARNING: CHECK AND RESET THE DATE! > cpu0: regulator not implemented > erase ^?, werase ^W, kill ^U, intr ^C, status ^T > > Welcome to the OpenBSD/arm64 7.4 installation program. > (I)nstall, (U)pgrade, (A)utoinstall or (S)hell? > > > Mizsei Zoltán írta 2023. nov.. 17, P-n 23:29 órakor: >> Hi, >> >> I have managed to boot OpenBSD using U-Boot's EFI implementation, here >> is the bootlog: >> >> --------- >> cannot open sd11a:/etc/random.seed: No such file or directory >> >> booting sd11a:/bsd: 2861736+1091248+12711584+634544 >> [233295+91+666048+260913]=0x13d5cf8 >> Copyright (c) 1982, 1986, 1989, 1991, 1993 >> >> The Regents of the University of California. All rights >> reserved. >> Copyright (c) 1995-2023 OpenBSD. All rights reserved. >> https://www.OpenBSD.org >> >> >> OpenBSD 7.4 (RAMDISK) #2131: Sun Oct 8 13:35:40 MDT 2023 >> >> dera...@arm64.openbsd.org:/usr/src/sys/arch/arm64/compile/RAMDISK >> >> real mem = 2036961280 (1942MB) >> >> avail mem = 1937559552 (1847MB) >> >> random: boothowto does not indicate good seed >> >> mainbus0 at root: Rockchip RK3568 Evaluation Board >> >> psci0 at mainbus0: PSCI 1.1, SMCCC 1.2, SYSTEM_SUSPEND >> >> efi0 at mainbus0: UEFI 2.0.5 >> >> cpu0 at mainbus0 mpidr 0: ARM Cortex-A55 r2p0 >> >> cpu0: 32KB 64b/line 4-way L1 VIPT I-cache, 32KB 64b/line 4-way L1 >> D-cache >> cpu0: 512KB 64b/line 16-way L2 cache >> >> cpu0: >> DP,RDM,Atomic,CRC32,SHA2,SHA1,AES+PMULL,LRCPC,DPB,ASID16,PAN+ATS1E1,LO,HPDS,VH,HAS >> agintc0 at mainbus0 shift 4:4 nirq 352 nredist 4: >> "interrupt-controller" >> syscon0 at mainbus0: "syscon" >> >> "reboot-mode" at syscon0 not configured >> >> syscon1 at mainbus0: "syscon" >> >> syscon2 at mainbus0: "syscon" >> >> syscon3 at mainbus0: "syscon" >> >> syscon4 at mainbus0: "syscon" >> >> syscon5 at mainbus0: "syscon" >> >> syscon6 at mainbus0: "syscon" >> >> syscon7 at mainbus0: "syscon" >> >> syscon8 at mainbus0: "syscon" >> >> rkclock0 at mainbus0: PMUCRU >> >> rkclock1 at mainbus0: CRU >> >> rkclock_set_frequency(rkclock0, 43, 100000000) >> >> rkclock_set_frequency(rkclock1, 3, 1000000000) >> >> rk3568_set_pll: 1188000000 Hz >> >> rkclock_set_frequency(rkclock1, 10, 600000000) >> >> rkclock_set_frequency(rkclock1, 269, 150000000) >> >> rkclock_set_frequency(rkclock1, 270, 100000000) >> >> rkclock_set_frequency(rkclock1, 371, 300000000) >> >> rkclock_set_frequency(rkclock1, 372, 200000000) >> >> rkclock_set_frequency(rkclock1, 373, 150000000) >> >> rkclock_set_frequency(rkclock1, 374, 100000000) >> >> rkclock_set_frequency(rkclock1, 201, 300000000) >> >> rkclock_set_frequency(rkclock1, 202, 150000000) >> >> rkclock_set_frequency(rkclock1, 6, 1200000000) >> >> syscon9 at mainbus0: "power-management" >> >> "power-controller" at syscon9 not configured >> >> syscon10 at mainbus0: "qos" >> >> syscon11 at mainbus0: "qos" >> >> syscon12 at mainbus0: "qos" >> >> syscon13 at mainbus0: "qos" >> >> syscon14 at mainbus0: "qos" >> >> syscon15 at mainbus0: "qos" >> >> syscon16 at mainbus0: "qos" >> >> syscon17 at mainbus0: "qos" >> >> syscon18 at mainbus0: "qos" >> >> syscon19 at mainbus0: "qos" >> >> syscon20 at mainbus0: "qos" >> >> syscon21 at mainbus0: "qos" >> >> syscon22 at mainbus0: "qos" >> >> syscon23 at mainbus0: "qos" >> >> syscon24 at mainbus0: "qos" >> >> syscon25 at mainbus0: "qos" >> >> syscon26 at mainbus0: "qos" >> >> syscon27 at mainbus0: "qos" >> >> syscon28 at mainbus0: "qos" >> >> syscon29 at mainbus0: "qos" >> >> syscon30 at mainbus0: "qos" >> >> syscon31 at mainbus0: "qos" >> >> syscon32 at mainbus0: "qos" >> >> syscon33 at mainbus0: "qos" >> >> syscon34 at mainbus0: "qos" >> >> syscon35 at mainbus0: "qos" >> >> syscon36 at mainbus0: "qos" >> >> rkusbphy0 at mainbus0: phy 0 >> >> rkpciephy0 at mainbus0 >> >> rkpinctrl0 at mainbus0: "pinctrl" >> >> rkgpio0 at rkpinctrl0 >> >> rkgpio1 at rkpinctrl0 >> >> rkgpio2 at rkpinctrl0 >> >> rkgpio3 at rkpinctrl0 >> >> rkgpio4 at rkpinctrl0 >> >> "cpu0-opp-table" at mainbus0 not configured >> >> "arm-pmu" at mainbus0 not configured >> >> "display-subsystem" at mainbus0 not configured >> >> agtimer0 at mainbus0: 24000 kHz >> >> "external-gmac0-clock" at mainbus0 not configured >> >> "external-gmac1-clock" at mainbus0 not configured >> >> "xin24m" at mainbus0 not configured >> >> rkdwusb0 at mainbus0: "usbdrd" >> >> xhci0 at rkdwusb0, xHCI 1.10 >> >> usb0 at xhci0: USB revision 3.0 >> >> uhub0 at usb0 configuration 1 interface 0 "Generic xHCI root hub" rev >> 3.00/1.00 addr 1 >> rkdwusb1 at mainbus0: "usbhost" >> >> xhci1 at rkdwusb1, xHCI 1.10 >> >> usb1 at xhci1: USB revision 3.0 >> >> uhub1 at usb1 configuration 1 interface 0 "Generic xHCI root hub" rev >> 3.00/1.00 addr 1 >> rkiic0 at mainbus0 >> >> iic0 at rkiic0 >> >> "atmel,24c02" at iic0 addr 0x50 not configured >> >> "pvtm" at mainbus0 not configured >> >> "opp-table2" at mainbus0 not configured >> >> "pvtm" at mainbus0 not configured >> >> "pvtm" at mainbus0 not configured >> >> dwpcie0 at mainbus0: no config registers >> >> dwmmc0 at mainbus0: 50 MHz base clock >> >> sdmmc0 at dwmmc0: 1-bit, dma >> >> dwmmc1 at mainbus0: 50 MHz base clock >> >> sdmmc1 at dwmmc1: 1-bit, dma >> >> "sfc" at mainbus0 not configured >> >> "sdhci" at mainbus0 not configured >> >> "nandc" at mainbus0 not configured >> >> "crypto" at mainbus0 not configured >> >> rkrng0 at mainbus0: ver 2 >> >> "secure_otp" at mainbus0 not configured >> >> "dmac" at mainbus0 not configured >> >> "dmac" at mainbus0 not configured >> >> "watchdog" at mainbus0 not configured >> >> com0 at mainbus0: dw16550, 64 byte fifo >> >> "saradc" at mainbus0 not configured >> >> "adc-keys" at mainbus0 not configured >> >> "framebuffer" at mainbus0 not configured >> >> uhub2 at uhub1 port 1 configuration 1 interface 0 "Terminus Technology >> USB2.0 HUB" rev 2 >> umass0 at uhub2 port 1 configuration 1 interface 0 "Sony Storage Media" >> rev 2.10/1.00 a3 >> umass0: using SCSI over Bulk-Only >> >> scsibus0 at umass0: 2 targets, initiator 0 >> >> sd0 at scsibus0 targ 1 lun 0: <Sony, Storage Media, PMAP> removable >> serial.054c09c2593A5 >> sd0: 29637MB, 512 bytes/sector, 60698112 sectors >> >> umass1 at uhub2 port 2 configuration 1 interface 0 "USB SanDisk >> 3.2Gen1" rev 2.10/1.00 4 >> umass1: using SCSI over Bulk-Only >> >> scsibus1 at umass1: 2 targets, initiator 0 >> >> sd1 at scsibus1 targ 1 lun 0: <USB, SanDisk 3.2Gen1, 1.00> removable >> serial.07815583810c >> sd1: 29340MB, 512 bytes/sector, 60088320 sectors >> >> softraid0 at root >> >> scsibus2 at softraid0: 256 targets >> >> root on rd0a swap on rd0b dump on rd0b >> >> WARNING: CHECK AND RESET THE DATE! >> >> rkclock_get_frequency(rkclock1, 10) >> >> cpu0: clock not implemented >> >> init: can't open /dev/console: Device not configured >> >> ----- >> >> Sadly there is no console over UART. I haven't checked HDMI yet. >> You can find the full story here: >> https://extrowerk.com/2023-10-30/Geniatech-XPI-3566-ZERO-SBC.html >> >> Best Regards, >> --Z-- >> >> >> Mizsei Zoltán írta 2023. nov.. 15, Sze-n 09:44 órakor: >>> Hi, >>> >>> i was unable to get any UART from uboot with the original firmware and >>> with my own built uboot. Geniatech confirmed they will fix it in a >>> future. The fix was released yesterday and now i can interact witrh >>> uboot. They haven't clarified what the issue was, but i suspect it was >>> in the miniloader (bootrom), as my own built uboot works now aswell. >>> >>> So, i tried to boot OpenBSD on it: >>> >>> I have downloaded the arm64 miniroot74.img and loop-mounted it on >>> linux. Mounted the EFI partition and inserted my own DTB file. Then i >>> dumped both the EFI and the OpenBSD partition into a separate >>> image-file (dd if=/dev/loop0p1 of=./EFI.img and dd if=/dev/loop0p4 >>> of=./BSD.img ) >>> >>> Then i manually created a parameter.txt file, which describes the >>> partition layout. I have created 4 partitions: UBOOT, EFI, ROOT, >>> USERDATA and wrote it into the MMC using rkdeveloptool. >>> Then i have flashed the images to the correct partition using >>> rkdeveloptool, so i have flashed u-boot to UBOOT, the EFI.img to the >>> EFI partition, the BSD.img to the ROOT partition and i have kept the >>> USERDATA empty for now. >>> >>> I have booted the board and it went straight to the U-Boot prompt, >>> where i have loaded the DTB and the EFI loader and started it. It >>> jumped into the OpenBSD bootloader just fine, but then i got stuck, as >>> the bootloader doesn't want to boot the ROOT partition, it complains >>> the partition is bad. See the logs below. >>> >>> I have also tried to boot the other partitions, but the result is the >>> same. Can you point out what am i doing wrong here? >>> >>> Thank You very much and have a great day! >>> >>> Best Regards, >>> -- Z -- >>> >>> -------------- >>> >>> BOOTLOG: >>> >>> DDR V1.18 f366f69a7d typ 23/07/17-15:48:58 >>> ln >>> LP4/4x derate en, other dram:1x trefi >>> ddrconfig:0 >>> LP4 MR14:0x4d >>> LPDDR4, 324MHz >>> BW=32 Col=10 Bk=8 CS0 Row=16 CS=1 Die BW=16 Size=2048MB >>> tdqss: cs0 dqs0: 48ps, dqs1: -72ps, dqs2: -48ps, dqs3: -96ps, >>> >>> change to: 324MHz >>> clk skew:0x60 >>> >>> change to: 528MHz >>> clk skew:0x58 >>> >>> change to: 780MHz >>> clk skew:0x58 >>> >>> change to: 1056MHz(final freq) >>> PHY drv:clk:38,ca:38,DQ:30,odt:60 >>> vrefinner:16%, vrefout:29% >>> dram drv:40,odt:80 >>> vref_ca:00000068 >>> clk skew:0x35 >>> cs 0: >>> the read training result: >>> DQS0:0x42, DQS1:0x40, DQS2:0x3e, DQS3:0x3c, >>> min : 0x9 0xd 0x10 0xd 0xd 0xd 0x9 0x1 , 0x3 0xb 0x1 0xd 0x11 >>> 0x10 0x12 0x10 , >>> 0xc 0xb 0xb 0x9 0x3 0x1 0x6 0x3 , 0x8 0x7 0x4 0x2 0xa >>> 0xc 0x7 0x9 , >>> mid :0x28 0x2b 0x2f 0x2c 0x2c 0x2a 0x28 0x20 ,0x22 0x2a 0x22 0x2d 0x30 >>> 0x30 0x30 0x2f , >>> 0x2a 0x2a 0x2a 0x28 0x21 0x20 0x24 0x23 ,0x26 0x26 0x23 0x21 0x28 >>> 0x2a 0x25 0x28 , >>> max :0x47 0x4a 0x4e 0x4c 0x4b 0x47 0x47 0x40 ,0x41 0x49 0x43 0x4d 0x50 >>> 0x50 0x4f 0x4e , >>> 0x48 0x49 0x49 0x47 0x40 0x3f 0x42 0x43 ,0x45 0x45 0x43 0x40 0x47 >>> 0x48 0x44 0x47 , >>> range:0x3e 0x3d 0x3e 0x3f 0x3e 0x3a 0x3e 0x3f ,0x3e 0x3e 0x42 0x40 0x3f >>> 0x40 0x3d 0x3e , >>> 0x3c 0x3e 0x3e 0x3e 0x3d 0x3e 0x3c 0x40 ,0x3d 0x3e 0x3f 0x3e 0x3d >>> 0x3c 0x3d 0x3e , >>> the write training result: >>> DQS0:0x3b, DQS1:0x2c, DQS2:0x2f, DQS3:0x29, >>> min :0x51 0x56 0x58 0x57 0x56 0x54 0x53 0x4d 0x56 ,0x40 0x48 0x42 0x4d >>> 0x4e 0x50 0x4f 0x, >>> 0x4c 0x4c 0x4c 0x4d 0x47 0x46 0x48 0x49 0x48 ,0x42 0x44 0x3f 0x3d >>> 0x47 0x48 0x43 0x, >>> mid :0x6f 0x73 0x76 0x74 0x73 0x71 0x70 0x6a 0x72 ,0x5d 0x66 0x5e 0x6a >>> 0x6b 0x6d 0x6b 0x, >>> 0x6a 0x6a 0x69 0x69 0x63 0x63 0x64 0x65 0x65 ,0x5e 0x60 0x5c 0x5a >>> 0x64 0x65 0x5f 0x, >>> max :0x8e 0x91 0x94 0x91 0x90 0x8f 0x8d 0x87 0x8f ,0x7b 0x84 0x7b 0x87 >>> 0x88 0x8a 0x88 0x, >>> 0x89 0x89 0x87 0x86 0x80 0x80 0x81 0x81 0x82 ,0x7b 0x7c 0x7a 0x78 >>> 0x81 0x83 0x7b 0x, >>> range:0x3d 0x3b 0x3c 0x3a 0x3a 0x3b 0x3a 0x3a 0x39 ,0x3b 0x3c 0x39 0x3a >>> 0x3a 0x3a 0x39 0x, >>> 0x3d 0x3d 0x3b 0x39 0x39 0x3a 0x39 0x38 0x3a ,0x39 0x38 0x3b 0x3b >>> 0x3a 0x3b 0x38 0x, >>> CA Training result: >>> cs:0 min :0x47 0x42 0x41 0x38 0x3c 0x34 0x42 ,0x48 0x40 0x40 0x38 0x3d >>> 0x34 0x42 , >>> cs:0 mid :0x83 0x84 0x7d 0x7a 0x78 0x77 0x6f ,0x83 0x81 0x7c 0x79 0x79 >>> 0x75 0x6f , >>> cs:0 max :0xc0 0xc6 0xb9 0xbc 0xb5 0xba 0x9d ,0xbf 0xc3 0xb8 0xbb 0xb6 >>> 0xb7 0x9d , >>> cs:0 range:0x79 0x84 0x78 0x84 0x79 0x86 0x5b ,0x77 0x83 0x78 0x83 0x79 >>> 0x83 0x5b , >>> out >>> U-Boot SPL board init >>> U-Boot SPL 2017.09-gaaca6ffec1-211203 #zzz (Dec 03 2021 - 18:42:16) >>> unknown raw ID phN >>> unrecognized JEDEC id bytes: 00, 00, 00 >>> Trying to boot from MMC2 >>> MMC error: The cmd index is 1, ret is -110 >>> Card did not respond to voltage select! >>> mmc_init: -95, time 10 >>> spl: mmc init failed with error: -95 >>> Trying to boot from MMC1 >>> No misc partition >>> Trying fit image at 0x4000 sector >>> ## Verified-boot: 0 >>> ## Checking atf-1 0x00040000 ... sha256(2f01bd8955...) + OK >>> ## Checking uboot 0x00a00000 ... sha256(1a594eea32...) + OK >>> ## Checking fdt 0x00b237b8 ... sha256(d408797509...) + OK >>> ## Checking atf-2 0xfdcc9000 ... sha256(f1fecab971...) + OK >>> ## Checking atf-3 0xfdcd0000 ... sha256(d7aa45eb18...) + OK >>> ## Checking optee 0x08400000 ... sha256(b8cddafab0...) + OK >>> Jumping to U-Boot(0x00a00000) via ARM Trusted Firmware(0x00040000) >>> Total: 222.321 ms >>> >>> INFO: Preloader serial: 7 >>> I/TC: >>> I/TC: Start rockchip platform init >>> I/TC: Rockchip release version: 1.0 >>> I/TC: OP-TEE version: 3.6.0-307-g0b06ae94 #1 Fri May 7 01:52:27 UTC >>> 2021 aarch64 >>> I/TC: Initialized >>> >>> >>> U-Boot 2017.09 (Nov 15 2023 - 08:31:01 +0100) >>> >>> Model: Rockchip RK3568 Evaluation Board >>> PreSerial: 7, raw, 0xfe6b0000 >>> DRAM: 2 GiB >>> Sysmem: init >>> Relocation Offset: 7d39d000, fdt: 7b9f9498 >>> Using default environment >>> >>> dwmmc@fe2b0000: 1, dwmmc@fe2c0000: 2, sdhci@fe310000: 0 >>> Bootdev(atags): mmc 0 >>> MMC0: HS200, 200Mhz >>> PartType: EFI >>> No misc partition >>> boot mode: None >>> FIT: No boot partition >>> No resource partition >>> Failed to load DTB >>> I2c0 speed: 100000Hz >>> rk8xx_read: read reg 0xed failed, ret=-121 >>> rk8xx_read: read reg 0xed failed, ret=-121 >>> of_get_regulator: Get (pmuio1-supply) regulator: >>> /i2c@fdd40000/pmic@20/regulators/LDO_REG1 >>> rk8xx_read: read reg 0xed failed, ret=-121 >>> of_get_regulator: Get (pmuio2-supply) regulator: >>> /i2c@fdd40000/pmic@20/regulators/LDO_REG1 >>> rk8xx_read: read reg 0xed failed, ret=-121 >>> of_get_regulator: Get (vccio1-supply) regulator: >>> /i2c@fdd40000/pmic@20/regulators/SWITCH_1 >>> rk8xx_read: read reg 0xed failed, ret=-121 >>> of_get_regulator: Get (vccio4-supply) regulator: >>> /i2c@fdd40000/pmic@20/regulators/DCDC_RE1 >>> rk8xx_read: read reg 0xed failed, ret=-121 >>> of_get_regulator: Get (vccio6-supply) regulator: >>> /i2c@fdd40000/pmic@20/regulators/SWITCH_1 >>> rk8xx_read: read reg 0xed failed, ret=-121 >>> of_get_regulator: Get (vccio7-supply) regulator: >>> /i2c@fdd40000/pmic@20/regulators/SWITCH_1 >>> io-domain: OK >>> Model: Rockchip RK3566 EVB2 LP4X V10 Board >>> rk8xx_read: read reg 0xed failed, ret=-121 >>> rk8xx_read: read reg 0xed failed, ret=-121 >>> No resource partition >>> No file: logo.bmp >>> failed to display uboot logo >>> board_late_init init >>> rkgtc board late init >>> get_ethaddr_from_eeprom >>> addr: >>> >>> ret:0 mac_addr: AC:DB:DA:63:CC:DF >>> >>> EEPROM: GENIATECH! >>> EEPROM: XPI3566Z23390003 >>> EEPROM: RE:DA:CT:ED >>> get ethaddr exist >>> mac_addr:RE:DA:CT:ED >>> etneaddr-buf:RE:DA:CT:ED >>> CLK: (sync kernel. arm: enter 816000 KHz, init 816000 KHz, kernel 0N/A) >>> apll 816000 KHz >>> dpll 528000 KHz >>> gpll 1188000 KHz >>> cpll 1000000 KHz >>> npll 1200000 KHz >>> vpll 24000 KHz >>> hpll 24000 KHz >>> ppll 200000 KHz >>> armclk 816000 KHz >>> aclk_bus 150000 KHz >>> pclk_bus 100000 KHz >>> aclk_top_high 500000 KHz >>> aclk_top_low 400000 KHz >>> hclk_top 150000 KHz >>> pclk_top 100000 KHz >>> aclk_perimid 300000 KHz >>> hclk_perimid 150000 KHz >>> pclk_pmu 100000 KHz >>> Net: No ethernet found. >>> Hit key to stop autoboot('CTRL+C'): 0 >>> ## Booting FIT Image FIT: No boot partition >>> FIT: No FIT image >>> Could not find misc partition >>> ANDROID: reboot reason: "(none)" >>> optee api revision: 2.0 >>> TEEC: Waring: Could not find security partition >>> Not AVB images, AVB skip >>> android_image_load_by_partname: Can't find part: boot >>> Android image load failed >>> Android boot failed, error -1. >>> MMC error: The cmd index is 1, ret is -110 >>> Card did not respond to voltage select! >>> mmc_init: -95, time 10 >>> switch to partitions #0, OK >>> mmc0(part 0) is current device >>> Failed to mount ext2 filesystem... >>> ** Unrecognized filesystem type ** >>> starting USB... >>> Bus dwc3@fcc00000: Register 2000140 NbrPorts 2 >>> Starting the controller >>> USB XHCI 1.10 >>> Bus dwc3@fd000000: Register 2000140 NbrPorts 2 >>> Starting the controller >>> USB XHCI 1.10 >>> scanning bus dwc3@fcc00000 for devices... 1 USB Device(s) found >>> scanning bus dwc3@fd000000 for devices... 1 USB Device(s) found >>> scanning usb for storage devices... 0 Storage Device(s) found >>> >>> Device 0: unknown device >>> No ethernet found. >>> missing environment variable: pxeuuid >>> missing environment variable: bootfile >>> Retrieving file: pxelinux.cfg/00000000 >>> No ethernet found. >>> missing environment variable: bootfile >>> Retrieving file: pxelinux.cfg/0000000 >>> No ethernet found. >>> missing environment variable: bootfile >>> Retrieving file: pxelinux.cfg/000000 >>> No ethernet found. >>> missing environment variable: bootfile >>> Retrieving file: pxelinux.cfg/00000 >>> No ethernet found. >>> missing environment variable: bootfile >>> Retrieving file: pxelinux.cfg/0000 >>> No ethernet found. >>> missing environment variable: bootfile >>> Retrieving file: pxelinux.cfg/000 >>> No ethernet found. >>> missing environment variable: bootfile >>> Retrieving file: pxelinux.cfg/00 >>> No ethernet found. >>> missing environment variable: bootfile >>> Retrieving file: pxelinux.cfg/0 >>> No ethernet found. >>> missing environment variable: bootfile >>> Retrieving file: pxelinux.cfg/default-arm-rockchip >>> No ethernet found. >>> missing environment variable: bootfile >>> Retrieving file: pxelinux.cfg/default-arm >>> No ethernet found. >>> missing environment variable: bootfile >>> Retrieving file: pxelinux.cfg/default >>> No ethernet found. >>> Config file not found >>> No ethernet found. >>> No ethernet found. >>> => mmc part >>> >>> Partition Map for MMC device 0 -- Partition Type: EFI >>> >>> Part Start LBA End LBA Name >>> Attributes >>> Type GUID >>> Partition GUID >>> 1 0x00004000 0x00005fff "uboot" >>> attrs: 0x0000000000000000 >>> type: 8dcd1602-5214-43f9-ffef-c49a4ee450b7 >>> guid: 5a30833f-8c43-47b1-a41d-84d40883d0c6 >>> 2 0x00028000 0x00067fff "EFI" >>> attrs: 0x0000000000000000 >>> type: 1124e418-9008-41f8-9e3d-8d872216c8a1 >>> guid: ebd0a0a2-b9e5-4433-87c0-68b6b72699c7 >>> 3 0x00078000 0x00c77fff "rootfs" >>> attrs: 0x0000000000000000 >>> type: fbd4486a-e42c-448d-d4e9-7f5c324a7843 >>> guid: 824cc7a0-36a8-11e3-890a-952519ad3f61 >>> 4 0x00cb8000 0x00e8ffde "userdata" >>> attrs: 0x0000000000000000 >>> type: bbaf4f47-230d-45b6-feae-e4b35f300b00 >>> guid: 824cc7a0-36a8-11e3-890a-952519ad3f62 >>> => load mmc 0:2 ${fdt_addr_r} dtb_from_linux.dtb >>> reading dtb_from_linux.dtb >>> 110592 bytes read in 11 ms (9.6 MiB/s) >>> => load mmc 0:2 ${kernel_addr_r} efi/boot/bootaa64.efi >>> reading efi/boot/bootaa64.efi >>> 219050 bytes read in 37 ms (5.6 MiB/s) >>> => bootefi ${kernel_addr_r} ${fdt_addr_r} >>> ## Starting EFI application at 00a80000 ... >>> MMC error: The cmd index is 1, ret is -110 >>> Card did not respond to voltage select! >>> mmc_init: -95, time 10 >>> Scanning disk dw...@fe2b0000.blk... >>> MMC: block number 0x1 exceeds max(0x0) >>> MMC: block number 0x1 exceeds max(0x0) >>> MMC error: The cmd index is 1, ret is -110 >>> Card did not respond to voltage select! >>> mmc_init: -95, time 51 >>> Scanning disk dw...@fe2c0000.blk... >>> MMC: block number 0x1 exceeds max(0x0) >>> MMC: block number 0x1 exceeds max(0x0) >>> unknown raw ID 7be01208 >>> Scanning disk fl...@0.blk... >>> unrecognized JEDEC id bytes: 00, 00, 00 >>> Scanning disk fl...@1.blk... >>> Scanning disk sd...@fe310000.blk... >>> Scanning disk na...@fe330000.blk... >>> Found 6 disks >>> No resource partition >>> No file: logo_kernel.bmp >>> Adding bank: 0x00200000 - 0x08400000 (size: 0x08200000) >>> Adding bank: 0x09400000 - 0x80000000 (size: 0x76c00000) >>> disks: sd0* sd1 sd2 sd3 sd4 >>>>> OpenBSD/arm64 BOOTAA64 1.18 >>> boot> set device sd3 >>> boot> boot >>> cannot open sd3:/etc/random.seed: bad partition >>> booting sd3:/bsd: open sd3:/bsd: bad partition >>> failed(99). will try /bsd >>> boot> >>> >>> ---------------- >>> >>> >>> Mizsei Zoltán írta 2023. okt.. 31, K-n 10:16 órakor: >>>> Hi, a short question: >>>> >>>> Is it possible to boot OpenBSD with the factory uboot bootloader or do >>>> we need an own-built Uboot for that? If an own built one is needed, can >>>> you instruct me, what features is necessary to be able to boot OBSD? >>>> >>>> Thank You very much! >>>> >>>> Best Regards, >>>> -- Zoltán >>>> >>>> Mizsei Zoltán írta 2023. okt.. 31, K-n 08:09 órakor: >>>>> In case you are interested, i document my jurney here (it is work in >>>>> progress): >>>>> https://extrowerk.com/2023-10-30/Geniatech-XPI-3566-ZERO-SBC.html >>>>> >>>>> Best regards, >>>>> --Z-- >>>>> >>>>> Mizsei Zoltán írta 2023. okt.. 18, Sze-n 07:43 órakor: >>>>>> Hi, >>>>>> >>>>>> i have just received an Geniatech XPI-3566 Zero SBC [1], which is a n >>>>>> RPi ZERO W2 alternative: >>>>>> >>>>>> Specs: >>>>>> CPU: 4xARM A55 max. 1,8Ghz >>>>>> GPU: ARM G52 2EE GPU >>>>>> RAM: 512M-8GB LPDDR4 (mine have 2G) >>>>>> SD card: NO !!! >>>>>> eMMC: 8GB eMMC >>>>>> wlan: AMPAK AP6256 >>>>>> >>>>>> The board comes with Debian preinstalled on the eMMC. The board boots, >>>>>> so it is in good working condition. >>>>>> >>>>>> On the first glance it should be moderately easily to get it work with >>>>>> OBSD, as the CPU and the wlan chip seems to be supported, and as far as >>>>>> i know the PM chip should be also supported. >>>>>> However there is no SD-Card slot and the eMMC is not removeable. AFAIK >>>>>> the RockChip boards uses a propertiary (?) protocol to flash the eMMC >>>>>> chip.So theoretically i should somehow repace the factory-default >>>>>> partitions with an OBSD root image using the official flasher (using >>>>>> windows). >>>>>> >>>>>> I would like tho use the board with HDMI output, and AFAIK for that >>>>>> EDK2 or uboot EFI support would be required. >>>>>> I haven't had yet enough time to check if the uboot have efi >>>>>> compatibility. >>>>>> >>>>>> I have found a port of Tianocore EDK II to Rockchip RK356x based SBCs, >>>>>> which lists HDMI supported with OpenBSD [1]. I did not tested it yet, >>>>>> as this should be flashed onto the eMMC, and i don't want to risk a >>>>>> brick. >>>>>> Possibly the EDK2 port needs to be adjusted first to support this >>>>>> specific board. Also maybe just maybe there is a USB support in the >>>>>> factory-default uboot, and maybe it is possible to chainload the EDK2 >>>>>> from a USB disk. >>>>>> Maybe i am completely wrong here. >>>>>> >>>>>> For more info see the attached dmesg from the factory-default linux. >>>>>> >>>>>> Do somebody have the same or similar board? Can sombodíy give me some >>>>>> hints? >>>>>> >>>>>> Thank You very much! >>>>>> >>>>>> Best Regards, >>>>>> -- Zoltan >>>>>> http://extrowerk.com >>>>>> >>>>>> [1] : https://www.geniatech.com/product/xpi-3566-zero/ >>>>>> [2] : https://github.com/jaredmcneill/quartz64_uefi >>>>>> >>>>>> >>>>>> DMESG from linux: >>>>>> [ 1.148647] Booting Linux on physical CPU 0x0000000000 [0x412fd050] >>>>>> [ 1.148671] Linux version 5.10.160 (geniatech@ubuntu22) >>>>>> (aarch64-none-linux-gnu-gcc (GNU Toolchain for the A-profile >>>>>> Architecture 10.3-2021.07 (arm-10.29)) 10.3.1 20210621, GNU ld (GNU >>>>>> Toolchain for the A-profile Architecture 10.3-2021.07 (arm-10.29)) >>>>>> 2.36.1.20210621) #1 SMP Fri Sep 8 10:45:44 CST 2023 >>>>>> [ 1.153011] Machine model: Rockchip RK3566 EVB2 LP4X V10 Board >>>>>> [ 1.153079] earlycon: uart8250 at MMIO32 0x00000000fe660000 (options >>>>>> '') >>>>>> [ 1.157370] printk: bootconsole [uart8250] enabled >>>>>> [ 1.158806] efi: UEFI not found. >>>>>> [ 1.194770] Zone ranges: >>>>>> [ 1.195027] DMA [mem 0x0000000000200000-0x000000007fffffff] >>>>>> [ 1.195617] DMA32 empty >>>>>> [ 1.195891] Normal empty >>>>>> [ 1.196166] Movable zone start for each node >>>>>> [ 1.196570] Early memory node ranges >>>>>> [ 1.196910] node 0: [mem 0x0000000000200000-0x00000000083fffff] >>>>>> [ 1.197504] node 0: [mem 0x0000000009400000-0x000000007fffffff] >>>>>> [ 1.198100] Initmem setup node 0 [mem >>>>>> 0x0000000000200000-0x000000007fffffff] >>>>>> [ 1.198768] On node 0 totalpages: 519680 >>>>>> [ 1.198773] DMA zone: 8184 pages used for memmap >>>>>> [ 1.198775] DMA zone: 0 pages reserved >>>>>> [ 1.198778] DMA zone: 519680 pages, LIFO batch:63 >>>>>> [ 1.214084] cma: Reserved 16 MiB at 0x000000007e800000 >>>>>> [ 1.214658] psci: probing for conduit method from DT. >>>>>> [ 1.215150] psci: PSCIv1.1 detected in firmware. >>>>>> [ 1.215587] psci: Using standard PSCI v0.2 function IDs >>>>>> [ 1.216085] psci: Trusted OS migration not required >>>>>> [ 1.216550] psci: SMC Calling Convention v1.2 >>>>>> [ 1.217352] percpu: Embedded 30 pages/cpu s83480 r8192 d31208 u122880 >>>>>> [ 1.217990] pcpu-alloc: s83480 r8192 d31208 u122880 alloc=30*4096 >>>>>> [ 1.217997] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 >>>>>> [ 1.218079] Detected VIPT I-cache on CPU0 >>>>>> [ 1.218501] CPU features: detected: GIC system register CPU interface >>>>>> [ 1.219112] CPU features: detected: Virtualization Host Extensions >>>>>> [ 1.219703] CPU features: detected: ARM errata 1165522, 1319367, or >>>>>> 1530923 >>>>>> [ 1.220369] alternatives: patching kernel code >>>>>> [ 1.222926] Built 1 zonelists, mobility grouping on. Total pages: >>>>>> 511496 >>>>>> [ 1.223577] Kernel command line: storagemedia=emmc >>>>>> androidboot.storagemedia=emmc androidboot.mode=normal >>>>>> androidboot.verifiedbootstate=orange rw rootwait >>>>>> earlycon=uart8250,mmio32,0xfe660000 console=ttyFIQ0 >>>>>> root=PARTUUID=614e0000-0000 >>>>>> [ 1.226258] Dentry cache hash table entries: 262144 (order: 9, >>>>>> 2097152 bytes, linear) >>>>>> [ 1.227246] Inode-cache hash table entries: 131072 (order: 8, >>>>>> 1048576 bytes, linear) >>>>>> [ 1.227981] mem auto-init: stack:off, heap alloc:off, heap free:off >>>>>> [ 1.256114] Memory: 1985732K/2078720K available (18112K kernel code, >>>>>> 3346K rwdata, 6044K rodata, 6592K init, 530K bss, 76604K reserved, >>>>>> 16384K cma-reserved) >>>>>> [ 1.257570] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, >>>>>> Nodes=1 >>>>>> [ 1.258221] ftrace: allocating 56170 entries in 220 pages >>>>>> [ 1.336694] ftrace: allocated 220 pages with 5 groups >>>>>> [ 1.337523] rcu: Hierarchical RCU implementation. >>>>>> [ 1.337978] rcu: RCU event tracing is enabled. >>>>>> [ 1.338409] rcu: RCU restricting CPUs from NR_CPUS=8 to >>>>>> nr_cpu_ids=4. >>>>>> [ 1.339028] Rude variant of Tasks RCU enabled. >>>>>> [ 1.339459] rcu: RCU calculated value of scheduler-enlistment delay >>>>>> is 30 jiffies. >>>>>> [ 1.340175] rcu: Adjusting geometry for rcu_fanout_leaf=16, >>>>>> nr_cpu_ids=4 >>>>>> [ 1.345602] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 >>>>>> [ 1.347364] GICv3: GIC: Using split EOI/Deactivate mode >>>>>> [ 1.347872] GICv3: 320 SPIs implemented >>>>>> [ 1.348236] GICv3: 0 Extended SPIs implemented >>>>>> [ 1.348693] GICv3: Distributor has no Range Selector support >>>>>> [ 1.349235] GICv3: 16 PPIs implemented >>>>>> [ 1.349627] GICv3: CPU0: found redistributor 0 region >>>>>> 0:0x00000000fd460000 >>>>>> [ 1.350401] ITS [mem 0xfd440000-0xfd45ffff] >>>>>> [ 1.350873] ITS@0x00000000fd440000: allocated 8192 Devices @25d0000 >>>>>> (indirect, esz 8, psz 64K, shr 0) >>>>>> [ 1.351777] ITS@0x00000000fd440000: allocated 32768 Interrupt >>>>>> Collections @25e0000 (flat, esz 2, psz 64K, shr 0) >>>>>> [ 1.352744] ITS: using cache flushing for cmd queue >>>>>> [ 1.353506] GICv3: using LPI property table @0x00000000025f0000 >>>>>> [ 1.354182] GIC: using cache flushing for LPI property table >>>>>> [ 1.354724] GICv3: CPU0: using allocated LPI pending table >>>>>> @0x0000000002600000 >>>>>> [ 1.385166] arch_timer: cp15 timer(s) running at 24.00MHz (phys). >>>>>> [ 1.385760] clocksource: arch_sys_counter: mask: 0xffffffffffffff >>>>>> max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns >>>>>> [ 1.386787] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps >>>>>> every 4398046511097ns >>>>>> [ 1.388366] Console: colour dummy device 80x25 >>>>>> [ 1.388821] Calibrating delay loop (skipped), value calculated using >>>>>> timer frequency.. 48.00 BogoMIPS (lpj=80000) >>>>>> [ 1.389798] pid_max: default: 32768 minimum: 301 >>>>>> [ 1.390373] Mount-cache hash table entries: 4096 (order: 3, 32768 >>>>>> bytes, linear) >>>>>> [ 1.391083] Mountpoint-cache hash table entries: 4096 (order: 3, >>>>>> 32768 bytes, linear) >>>>>> [ 1.393277] rcu: Hierarchical SRCU implementation. >>>>>> [ 1.394488] Platform MSI: interrupt-controller@fd440000 domain >>>>>> created >>>>>> [ 1.395516] PCI/MSI: >>>>>> /interrupt-controller@fd400000/interrupt-controller@fd440000 domain >>>>>> created >>>>>> [ 1.396585] EFI services will not be available. >>>>>> [ 1.397369] smp: Bringing up secondary CPUs ... >>>>>> [ 1.399090] Detected VIPT I-cache on CPU1 >>>>>> [ 1.399124] GICv3: CPU1: found redistributor 100 region >>>>>> 0:0x00000000fd480000 >>>>>> [ 1.399145] GICv3: CPU1: using allocated LPI pending table >>>>>> @0x0000000002610000 >>>>>> [ 1.399197] CPU1: Booted secondary processor 0x0000000100 >>>>>> [0x412fd050] >>>>>> [ 1.400538] Detected VIPT I-cache on CPU2 >>>>>> [ 1.400567] GICv3: CPU2: found redistributor 200 region >>>>>> 0:0x00000000fd4a0000 >>>>>> [ 1.400585] GICv3: CPU2: using allocated LPI pending table >>>>>> @0x0000000002620000 >>>>>> [ 1.400623] CPU2: Booted secondary processor 0x0000000200 >>>>>> [0x412fd050] >>>>>> [ 1.401916] Detected VIPT I-cache on CPU3 >>>>>> [ 1.401940] GICv3: CPU3: found redistributor 300 region >>>>>> 0:0x00000000fd4c0000 >>>>>> [ 1.401957] GICv3: CPU3: using allocated LPI pending table >>>>>> @0x0000000002630000 >>>>>> [ 1.401993] CPU3: Booted secondary processor 0x0000000300 >>>>>> [0x412fd050] >>>>>> [ 1.402085] smp: Brought up 1 node, 4 CPUs >>>>>> [ 1.409548] SMP: Total of 4 processors activated. >>>>>> [ 1.409997] CPU features: detected: Privileged Access Never >>>>>> [ 1.410525] CPU features: detected: User Access Override >>>>>> [ 1.411029] CPU features: detected: 32-bit EL0 Support >>>>>> [ 1.411516] CPU features: detected: Common not Private translations >>>>>> [ 1.412108] CPU features: detected: RAS Extension Support >>>>>> [ 1.412620] CPU features: detected: Data cache clean to the PoU not >>>>>> required for I/D coherence >>>>>> [ 1.413442] CPU features: detected: CRC32 instructions >>>>>> [ 1.413930] CPU features: detected: Speculative Store Bypassing Safe >>>>>> (SSBS) >>>>>> [ 1.414589] CPU features: detected: RCpc load-acquire (LDAPR) >>>>>> [ 1.415208] CPU: All CPU(s) started at EL2 >>>>>> [ 1.416686] devtmpfs: initialized >>>>>> [ 1.431695] Registered cp15_barrier emulation handler >>>>>> [ 1.432195] Registered setend emulation handler >>>>>> [ 1.432790] clocksource: jiffies: mask: 0xffffffff max_cycles: >>>>>> 0xffffffff, max_idle_ns: 6370867519511994 ns >>>>>> [ 1.433724] futex hash table entries: 1024 (order: 4, 65536 bytes, >>>>>> linear) >>>>>> [ 1.434916] pinctrl core: initialized pinctrl subsystem >>>>>> [ 1.435968] DMI not present or invalid. >>>>>> [ 1.436749] NET: Registered protocol family 16 >>>>>> [ 1.438908] DMA: preallocated 256 KiB GFP_KERNEL pool for atomic >>>>>> allocations >>>>>> [ 1.439754] DMA: preallocated 256 KiB GFP_KERNEL|GFP_DMA pool for >>>>>> atomic allocations >>>>>> [ 1.442221] Registered FIQ tty driver >>>>>> [ 1.442908] thermal_sys: Registered thermal governor 'fair_share' >>>>>> [ 1.442914] thermal_sys: Registered thermal governor 'step_wise' >>>>>> [ 1.443522] thermal_sys: Registered thermal governor 'user_space' >>>>>> [ 1.444092] thermal_sys: Registered thermal governor >>>>>> 'power_allocator' >>>>>> [ 1.444951] thermal thermal_zone1: power_allocator: >>>>>> sustainable_power will be estimated >>>>>> [ 1.446383] cpuidle: using governor menu >>>>>> [ 1.447034] hw-breakpoint: found 6 breakpoint and 4 watchpoint >>>>>> registers. >>>>>> [ 1.447802] ASID allocator initialised with 65536 entries >>>>>> [ 1.450755] ramoops: dmesg-0 0x20000@0x0000000000110000 >>>>>> [ 1.451270] ramoops: console 0x80000@0x0000000000130000 >>>>>> [ 1.451786] ramoops: pmsg 0x50000@0x00000000001b0000 >>>>>> [ 1.452632] printk: console [ramoops-1] enabled >>>>>> [ 1.453065] pstore: Registered ramoops as persistent store backend >>>>>> [ 1.453670] ramoops: using 0xf0000@0x110000, ecc: 0 >>>>>> [ 1.481321] rockchip-gpio fdd60000.gpio0: probed >>>>>> /pinctrl/gpio0@fdd60000 >>>>>> [ 1.482484] rockchip-gpio fe740000.gpio1: probed >>>>>> /pinctrl/gpio1@fe740000 >>>>>> [ 1.483564] rockchip-gpio fe750000.gpio2: probed >>>>>> /pinctrl/gpio2@fe750000 >>>>>> [ 1.484703] rockchip-gpio fe760000.gpio3: probed >>>>>> /pinctrl/gpio3@fe760000 >>>>>> [ 1.485874] rockchip-gpio fe770000.gpio4: probed >>>>>> /pinctrl/gpio4@fe770000 >>>>>> [ 1.486593] rockchip-pinctrl pinctrl: probed pinctrl >>>>>> [ 1.508349] fiq_debugger fiq_debugger.0: IRQ fiq not found >>>>>> [ 1.508899] fiq_debugger fiq_debugger.0: IRQ wakeup not found >>>>>> [ 1.509452] fiq_debugger_probe: could not install nmi irq handler >>>>>> [ 1.510122] printk: console [ttyFIQ0] enabled >>>>>> [ 1.510550] printk: bootconsole [uart8250] disabled >>>>>> [ 1.511229] Registered fiq debugger ttyFIQ0 >>>>>> [ 1.511977] vcc3v3_sys: supplied by dc_12v >>>>>> [ 1.512240] vcc5v0_sys: supplied by dc_12v >>>>>> [ 1.512513] vcc5v0_usb: supplied by dc_12v >>>>>> [ 1.512883] vcc5v0_host: supplied by vcc5v0_usb >>>>>> [ 1.513334] vcc5v0_otg: supplied by vcc5v0_usb >>>>>> [ 1.514355] vcc3v3_pcie: supplied by dc_12v >>>>>> [ 1.515203] iommu: Default domain type: Translated >>>>>> [ 1.518473] SCSI subsystem initialized >>>>>> [ 1.518522] libata version 3.00 loaded. >>>>>> [ 1.518680] usbcore: registered new interface driver usbfs >>>>>> [ 1.518729] usbcore: registered new interface driver hub >>>>>> [ 1.518769] usbcore: registered new device driver usb >>>>>> [ 1.518856] mc: Linux media interface: v0.10 >>>>>> [ 1.518884] videodev: Linux video capture interface: v2.00 >>>>>> [ 1.518958] pps_core: LinuxPPS API ver. 1 registered >>>>>> [ 1.518967] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 >>>>>> Rodolfo Giometti <giome...@linux.it> >>>>>> [ 1.518984] PTP clock support registered >>>>>> [ 1.519609] arm-scmi firmware:scmi: SCMI Notifications - Core >>>>>> Enabled. >>>>>> [ 1.519679] arm-scmi firmware:scmi: SCMI Protocol v2.0 'rockchip:' >>>>>> Firmware version 0x0 >>>>>> [ 1.521610] Advanced Linux Sound Architecture Driver Initialized. >>>>>> [ 1.522026] Bluetooth: Core ver 2.22 >>>>>> [ 1.522063] NET: Registered protocol family 31 >>>>>> [ 1.522071] Bluetooth: HCI device and connection manager initialized >>>>>> [ 1.522085] Bluetooth: HCI socket layer initialized >>>>>> [ 1.522096] Bluetooth: L2CAP socket layer initialized >>>>>> [ 1.522115] Bluetooth: SCO socket layer initialized >>>>>> [ 1.522586] rockchip-cpuinfo cpuinfo: SoC : 35662000 >>>>>> [ 1.522600] rockchip-cpuinfo cpuinfo: Serial : >>>>>> 3cb4e04f0cd3ac4f >>>>>> [ 1.523306] clocksource: Switched to clocksource arch_sys_counter >>>>>> [ 1.986686] NET: Registered protocol family 2 >>>>>> [ 1.986910] IP idents hash table entries: 32768 (order: 6, 262144 >>>>>> bytes, linear) >>>>>> [ 1.988141] tcp_listen_portaddr_hash hash table entries: 1024 >>>>>> (order: 2, 16384 bytes, linear) >>>>>> [ 1.988184] TCP established hash table entries: 16384 (order: 5, >>>>>> 131072 bytes, linear) >>>>>> [ 1.988279] TCP bind hash table entries: 16384 (order: 6, 262144 >>>>>> bytes, linear) >>>>>> [ 1.988499] TCP: Hash tables configured (established 16384 bind >>>>>> 16384) >>>>>> [ 1.988625] UDP hash table entries: 1024 (order: 3, 32768 bytes, >>>>>> linear) >>>>>> [ 1.988662] UDP-Lite hash table entries: 1024 (order: 3, 32768 >>>>>> bytes, linear) >>>>>> [ 1.988830] NET: Registered protocol family 1 >>>>>> [ 1.989309] RPC: Registered named UNIX socket transport module. >>>>>> [ 1.989321] RPC: Registered udp transport module. >>>>>> [ 1.989328] RPC: Registered tcp transport module. >>>>>> [ 1.989334] RPC: Registered tcp NFSv4.1 backchannel transport module. >>>>>> [ 1.990280] PCI: CLS 0 bytes, default 64 >>>>>> [ 1.992575] rockchip-thermal fe710000.tsadc: tsadc is probed >>>>>> successfully! >>>>>> [ 1.993623] hw perfevents: enabled with armv8_cortex_a55 PMU driver, >>>>>> 7 counters available >>>>>> [ 1.997614] Initialise system trusted keyrings >>>>>> [ 1.997782] workingset: timestamp_bits=62 max_order=19 bucket_order=0 >>>>>> [ 2.001667] squashfs: version 4.0 (2009/01/31) Phillip Lougher >>>>>> [ 2.002209] NFS: Registering the id_resolver key type >>>>>> [ 2.002247] Key type id_resolver registered >>>>>> [ 2.002256] Key type id_legacy registered >>>>>> [ 2.002288] ntfs: driver 2.1.32 [Flags: R/O]. >>>>>> [ 2.002490] jffs2: version 2.2. (NAND) \xc2\xa9 2001-2006 Red Hat, >>>>>> Inc. >>>>>> [ 2.002737] fuse: init (API version 7.32) >>>>>> [ 2.003025] SGI XFS with security attributes, no debug enabled >>>>>> [ 2.038140] NET: Registered protocol family 38 >>>>>> [ 2.038173] Key type asymmetric registered >>>>>> [ 2.038183] Asymmetric key parser 'x509' registered >>>>>> [ 2.038228] Block layer SCSI generic (bsg) driver version 0.4 loaded >>>>>> (major 242) >>>>>> [ 2.038239] io scheduler mq-deadline registered >>>>>> [ 2.038246] io scheduler kyber registered >>>>>> [ 2.038875] rockchip-csi2-dphy-hw fe870000.csi2-dphy-hw: csi2 dphy >>>>>> hw probe successfully! >>>>>> [ 2.039618] rockchip-csi2-dphy csi2-dphy1: csi2 dphy1 probe >>>>>> successfully! >>>>>> [ 2.048935] pwm-backlight backlight: supply power not found, using >>>>>> dummy regulator >>>>>> [ 2.049412] pwm-backlight backlight1: supply power not found, using >>>>>> dummy regulator >>>>>> [ 2.049936] iep: Module initialized. >>>>>> [ 2.054054] dma-pl330 fe530000.dmac: Loaded driver for PL330 >>>>>> DMAC-241330 >>>>>> [ 2.054094] dma-pl330 fe530000.dmac: DBUFF-128x8bytes Num_Chans-8 >>>>>> Num_Peri-32 Num_Events-16 >>>>>> [ 2.055865] dma-pl330 fe550000.dmac: Loaded driver for PL330 >>>>>> DMAC-241330 >>>>>> [ 2.055892] dma-pl330 fe550000.dmac: DBUFF-128x8bytes Num_Chans-8 >>>>>> Num_Peri-32 Num_Events-16 >>>>>> [ 2.056579] rockchip-pvtm fde00000.pvtm: pvtm@0 probed >>>>>> [ 2.056748] rockchip-pvtm fde80000.pvtm: pvtm@1 probed >>>>>> [ 2.056865] rockchip-pvtm fde90000.pvtm: pvtm@2 probed >>>>>> [ 2.057442] rockchip-system-monitor rockchip-system-monitor: system >>>>>> monitor probe >>>>>> [ 2.058160] arm-scmi firmware:scmi: Failed. SCMI protocol 22 not >>>>>> active. >>>>>> [ 2.058416] Serial: 8250/16550 driver, 10 ports, IRQ sharing disabled >>>>>> [ 2.059407] fe650000.serial: ttyS1 at MMIO 0xfe650000 (irq = 55, >>>>>> base_baud = 1500000) is a 16550A >>>>>> [ 2.060001] fe680000.serial: ttyS4 at MMIO 0xfe680000 (irq = 56, >>>>>> base_baud = 1500000) is a 16550A >>>>>> [ 2.060509] fe6d0000.serial: ttyS9 at MMIO 0xfe6d0000 (irq = 57, >>>>>> base_baud = 1500000) is a 16550A >>>>>> [ 2.062662] random: crng init done >>>>>> [ 2.063407] rockchip-vop2 fe040000.vop: Adding to iommu group 7 >>>>>> [ 2.069729] rockchip-vop2 fe040000.vop: [drm:vop2_bind] vp0 assign >>>>>> plane mask: 0x3f, primary plane phy id: 4 >>>>>> [ 2.069773] rockchip-vop2 fe040000.vop: [drm:vop2_bind] vp1 assign >>>>>> plane mask: 0x0, primary plane phy id: -1 >>>>>> [ 2.069785] rockchip-vop2 fe040000.vop: [drm:vop2_bind] vp2 assign >>>>>> plane mask: 0x0, primary plane phy id: -1 >>>>>> [ 2.069922] rockchip-vop2 fe040000.vop: [drm:vop2_bind] >>>>>> Cluster0-win0 as cursor plane for vp0 >>>>>> [ 2.070024] [drm] failed to init overlay plane Cluster0-win1 >>>>>> [ 2.070119] rockchip-drm display-subsystem: bound fe040000.vop (ops >>>>>> 0xffffffc0092bcd98) >>>>>> [ 2.070417] dwhdmi-rockchip fe0a0000.hdmi: Detected HDMI TX >>>>>> controller v2.11a with HDCP (DWC HDMI 2.0 TX PHY) >>>>>> [ 2.070968] dwhdmi-rockchip fe0a0000.hdmi: registered DesignWare >>>>>> HDMI I2C bus driver >>>>>> [ 2.071177] dwhdmi-rockchip fe0a0000.hdmi: IRQ index 1 not found >>>>>> [ 2.071559] rockchip-drm display-subsystem: bound fe0a0000.hdmi (ops >>>>>> 0xffffffc0092cb900) >>>>>> [ 2.198563] rockchip-drm display-subsystem: [drm] fb0: rockchipdrmfb >>>>>> frame buffer device >>>>>> [ 2.199324] [drm] Initialized rockchip 3.0.0 20140818 for >>>>>> display-subsystem on minor 0 >>>>>> [ 2.203963] input: hdmi_cec_key as >>>>>> /devices/platform/fe0a0000.hdmi/dw-hdmi-cec.1.auto/input/input0 >>>>>> [ 2.204731] mali fde60000.gpu: Kernel DDK version g18p0-01eac0 >>>>>> [ 2.204817] cacheinfo: Unable to detect cache hierarchy for CPU 0 >>>>>> [ 2.204860] mali fde60000.gpu: bin=0 >>>>>> [ 2.204926] mali fde60000.gpu: leakage=6 >>>>>> [ 2.204995] mali fde60000.gpu: pvtm = 84490, from nvmem >>>>>> [ 2.205017] mali fde60000.gpu: pvtm-volt-sel=1 >>>>>> [ 2.205452] brd: module loaded >>>>>> [ 2.205624] mali fde60000.gpu: avs=0 >>>>>> [ 2.205656] W : [File] : >>>>>> drivers/gpu/arm/bifrost/platform/rk/mali_kbase_config_rk.c; [Line] : >>>>>> 143; [Func] : kbase_platform_rk_init(); power-off-delay-ms not >>>>>> available. >>>>>> [ 2.206013] mali fde60000.gpu: GPU identified as 0x2 arch 7.4.0 r1p0 >>>>>> status 0 >>>>>> [ 2.206090] mali fde60000.gpu: No priority control manager is >>>>>> configured >>>>>> [ 2.206295] mali fde60000.gpu: No memory group manager is configured >>>>>> [ 2.208228] mali fde60000.gpu: l=0 h=2147483647 hyst=5000 >>>>>> l_limit=700000000 h_limit=0 h_table=0 >>>>>> [ 2.209104] mali fde60000.gpu: Probed as mali0 >>>>>> [ 2.211441] loop: module loaded >>>>>> [ 2.211798] zram: Added device: zram0 >>>>>> [ 2.212023] lkdtm: No crash points registered, enable through debugfs >>>>>> [ 2.215819] rockchip-spi fe640000.spi: no high_speed pinctrl state >>>>>> [ 2.215909] spi_dev@0 enforce active low on chipselect handle >>>>>> [ 2.216607] rockchip-spi fe640000.spi: probed, poll=0, rsd=0, >>>>>> cs-inactive=0, ready=0 >>>>>> [ 2.218149] spi-nand spi4.0: unknown raw ID 00000000 >>>>>> [ 2.218185] spi-nand: probe of spi4.0 failed with error -524 >>>>>> [ 2.220197] usbcore: registered new interface driver rtl8150 >>>>>> [ 2.220258] usbcore: registered new interface driver r8152 >>>>>> [ 2.230950] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) >>>>>> Driver >>>>>> [ 2.230990] ehci-pci: EHCI PCI platform driver >>>>>> [ 2.231070] ehci-platform: EHCI generic platform driver >>>>>> [ 2.231325] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver >>>>>> [ 2.231344] ohci-platform: OHCI generic platform driver >>>>>> [ 2.231923] xhci-hcd xhci-hcd.4.auto: xHCI Host Controller >>>>>> [ 2.232124] xhci-hcd xhci-hcd.4.auto: new USB bus registered, >>>>>> assigned bus number 1 >>>>>> [ 2.232267] xhci-hcd xhci-hcd.4.auto: hcc params 0x0220fe64 hci >>>>>> version 0x110 quirks 0x0000200002010010 >>>>>> [ 2.232330] xhci-hcd xhci-hcd.4.auto: irq 70, io mem 0xfd000000 >>>>>> [ 2.232612] usb usb1: New USB device found, idVendor=1d6b, >>>>>> idProduct=0002, bcdDevice= 5.10 >>>>>> [ 2.232624] usb usb1: New USB device strings: Mfr=3, Product=2, >>>>>> SerialNumber=1 >>>>>> [ 2.232633] usb usb1: Product: xHCI Host Controller >>>>>> [ 2.232641] usb usb1: Manufacturer: Linux 5.10.160 xhci-hcd >>>>>> [ 2.232649] usb usb1: SerialNumber: xhci-hcd.4.auto >>>>>> [ 2.233067] hub 1-0:1.0: USB hub found >>>>>> [ 2.233113] hub 1-0:1.0: 1 port detected >>>>>> [ 2.233441] xhci-hcd xhci-hcd.4.auto: xHCI Host Controller >>>>>> [ 2.233590] xhci-hcd xhci-hcd.4.auto: new USB bus registered, >>>>>> assigned bus number 2 >>>>>> [ 2.233609] xhci-hcd xhci-hcd.4.auto: Host supports USB 3.0 >>>>>> SuperSpeed >>>>>> [ 2.233674] usb usb2: We don't know the algorithms for LPM for this >>>>>> host, disabling LPM. >>>>>> [ 2.233774] usb usb2: New USB device found, idVendor=1d6b, >>>>>> idProduct=0003, bcdDevice= 5.10 >>>>>> [ 2.233785] usb usb2: New USB device strings: Mfr=3, Product=2, >>>>>> SerialNumber=1 >>>>>> [ 2.233794] usb usb2: Product: xHCI Host Controller >>>>>> [ 2.233801] usb usb2: Manufacturer: Linux 5.10.160 xhci-hcd >>>>>> [ 2.233809] usb usb2: SerialNumber: xhci-hcd.4.auto >>>>>> [ 2.234190] hub 2-0:1.0: USB hub found >>>>>> [ 2.234227] hub 2-0:1.0: 1 port detected >>>>>> [ 2.234628] usbcore: registered new interface driver cdc_acm >>>>>> [ 2.234638] cdc_acm: USB Abstract Control Model driver for USB >>>>>> modems and ISDN adapters >>>>>> [ 2.234910] usbcore: registered new interface driver uas >>>>>> [ 2.234977] usbcore: registered new interface driver usb-storage >>>>>> [ 2.235060] usbcore: registered new interface driver >>>>>> usbserial_generic >>>>>> [ 2.235085] usbserial: USB Serial support registered for generic >>>>>> [ 2.235122] usbcore: registered new interface driver cp210x >>>>>> [ 2.235147] usbserial: USB Serial support registered for cp210x >>>>>> [ 2.235191] usbcore: registered new interface driver ftdi_sio >>>>>> [ 2.235216] usbserial: USB Serial support registered for FTDI USB >>>>>> Serial Device >>>>>> [ 2.235279] usbcore: registered new interface driver keyspan >>>>>> [ 2.235303] usbserial: USB Serial support registered for Keyspan - >>>>>> (without firmware) >>>>>> [ 2.235324] usbserial: USB Serial support registered for Keyspan 1 >>>>>> port adapter >>>>>> [ 2.235344] usbserial: USB Serial support registered for Keyspan 2 >>>>>> port adapter >>>>>> [ 2.235364] usbserial: USB Serial support registered for Keyspan 4 >>>>>> port adapter >>>>>> [ 2.235401] usbcore: registered new interface driver option >>>>>> [ 2.235423] usbserial: USB Serial support registered for GSM modem >>>>>> (1-port) >>>>>> [ 2.235506] usbcore: registered new interface driver oti6858 >>>>>> [ 2.235532] usbserial: USB Serial support registered for oti6858 >>>>>> [ 2.235569] usbcore: registered new interface driver pl2303 >>>>>> [ 2.235592] usbserial: USB Serial support registered for pl2303 >>>>>> [ 2.235630] usbcore: registered new interface driver qcserial >>>>>> [ 2.235652] usbserial: USB Serial support registered for Qualcomm >>>>>> USB modem >>>>>> [ 2.235694] usbcore: registered new interface driver sierra >>>>>> [ 2.235717] usbserial: USB Serial support registered for Sierra USB >>>>>> modem >>>>>> [ 2.237058] usbcore: registered new interface driver usbtouchscreen >>>>>> [ 2.237567] i2c /dev entries driver >>>>>> [ 2.238510] at24 0-0050: supply vcc not found, using dummy regulator >>>>>> [ 2.239274] at24 0-0050: 256 byte 24c02 EEPROM, writable, 1 >>>>>> bytes/write >>>>>> [ 2.239710] fan53555-regulator 0-001c: Failed to get chip ID! >>>>>> [ 2.241105] rk808 0-0020: failed to read the chip id at 0x17 >>>>>> [ 2.243048] <<GTP-INF>>[gt1x_ts_probe:560] GTP Driver Version: >>>>>> V1.4<2015/07/10> >>>>>> [ 2.243072] <<GTP-INF>>[gt1x_ts_probe:561] GTP I2C Address: 0x14 >>>>>> [ 2.243126] <<GTP-ERR>>[gt1x_parse_dt:341] vdd_ana not specified, >>>>>> fallback to power-supply >>>>>> [ 2.243464] <<GTP-INF>>[gt1x_parse_dt:348] Power Invert,no >>>>>> [ 2.243557] <<GTP-INF>>[gt1x_reset_guitar:788] GTP RESET! >>>>>> [ 2.263320] ov5647 xclk >>>>>> [ 2.263373] ov5647 detect >>>>>> [ 2.313508] <<GTP-ERR>>[_do_i2c_write:432] I2c transfer error! (-6) >>>>>> [ 2.313527] <<GTP-ERR>>[gt1x_init:2319] Reset guitar failed! >>>>>> [ 2.313535] <<GTP-INF>>[gt1x_reset_guitar:788] GTP RESET! >>>>>> [ 2.383478] <<GTP-ERR>>[_do_i2c_write:432] I2c transfer error! (-6) >>>>>> [ 2.383496] <<GTP-ERR>>[gt1x_init:2319] Reset guitar failed! >>>>>> [ 2.383503] <<GTP-INF>>[gt1x_reset_guitar:788] GTP RESET! >>>>>> [ 2.430173] ov5647 2-0036: ov5647_write: i2c write error, reg: 103 >>>>>> [ 2.432265] rkisp_hw fdff0000.rkisp: Adding to iommu group 6 >>>>>> [ 2.432497] rkisp_hw fdff0000.rkisp: is_thunderboot: 0 >>>>>> [ 2.432512] rkisp_hw fdff0000.rkisp: max input:0x0@0fps >>>>>> [ 2.432542] rkisp_hw fdff0000.rkisp: can't request region for >>>>>> resource [mem 0xfdff0000-0xfdffffff] >>>>>> [ 2.432751] rkisp_hw fdff0000.rkisp: no find phandle sram >>>>>> [ 2.433227] rkisp rkisp-vir0: rkisp driver version: v02.02.02 >>>>>> [ 2.433360] rkisp rkisp-vir0: No memory-region-thunderboot specified >>>>>> [ 2.433569] rkisp rkisp-vir0: Entity type for entity >>>>>> rkisp-isp-subdev was not initialized! >>>>>> [ 2.433591] rkisp rkisp-vir0: Entity type for entity >>>>>> rkisp-csi-subdev was not initialized! >>>>>> [ 2.435966] usbcore: registered new interface driver uvcvideo >>>>>> [ 2.435985] USB Video Class driver (1.1.1) >>>>>> [ 2.437528] Bluetooth: HCI UART driver ver 2.3 >>>>>> [ 2.437548] Bluetooth: HCI UART protocol H4 registered >>>>>> [ 2.437556] Bluetooth: HCI UART protocol ATH3K registered >>>>>> [ 2.437618] usbcore: registered new interface driver bfusb >>>>>> [ 2.437661] usbcore: registered new interface driver btusb >>>>>> [ 2.438169] cpu cpu0: leakage=17 >>>>>> [ 2.438218] cpu cpu0: pvtm = 84490, from nvmem >>>>>> [ 2.438235] cpu cpu0: pvtm-volt-sel=1 >>>>>> [ 2.440137] sdhci: Secure Digital Host Controller Interface driver >>>>>> [ 2.440156] sdhci: Copyright(c) Pierre Ossman >>>>>> [ 2.440163] Synopsys Designware Multimedia Card Interface Driver >>>>>> [ 2.440755] sdhci-pltfm: SDHCI platform and OF driver helper >>>>>> [ 2.441136] dwmmc_rockchip fe2c0000.dwmmc: No normal pinctrl state >>>>>> [ 2.441153] dwmmc_rockchip fe2c0000.dwmmc: No idle pinctrl state >>>>>> [ 2.441280] dwmmc_rockchip fe2c0000.dwmmc: IDMAC supports 32-bit >>>>>> address mode. >>>>>> [ 2.441310] dwmmc_rockchip fe2c0000.dwmmc: Using internal DMA >>>>>> controller. >>>>>> [ 2.441324] dwmmc_rockchip fe2c0000.dwmmc: Version ID is 270a >>>>>> [ 2.441393] dwmmc_rockchip fe2c0000.dwmmc: DW MMC controller at irq >>>>>> 41,32 bit host data width,256 deep fifo >>>>>> [ 2.441707] dwmmc_rockchip fe2c0000.dwmmc: allocated mmc-pwrseq >>>>>> [ 2.441725] mmc_host mmc2: card is non-removable. >>>>>> [ 2.442199] arm-scmi firmware:scmi: Failed. SCMI protocol 17 not >>>>>> active. >>>>>> [ 2.442293] SMCCC: SOC_ID: ARCH_SOC_ID not implemented, skipping .... >>>>>> [ 2.443069] cryptodev: driver 1.12 loaded. >>>>>> [ 2.443146] hid: raw HID events driver (C) Jiri Kosina >>>>>> [ 2.443610] usbcore: registered new interface driver usbhid >>>>>> [ 2.443622] usbhid: USB HID core driver >>>>>> [ 2.447359] usbcore: registered new interface driver snd-usb-audio >>>>>> [ 2.453530] Initializing XFRM netlink socket >>>>>> [ 2.453668] <<GTP-ERR>>[_do_i2c_write:432] I2c transfer error! (-6) >>>>>> [ 2.453683] <<GTP-ERR>>[gt1x_init:2319] Reset guitar failed! >>>>>> [ 2.453691] <<GTP-INF>>[gt1x_reset_guitar:788] GTP RESET! >>>>>> [ 2.453796] mmc_host mmc2: Bus speed (slot 0) = 375000Hz (slot req >>>>>> 400000Hz, actual 375000HZ div = 0) >>>>>> [ 2.453970] NET: Registered protocol family 10 >>>>>> [ 2.454782] Segment Routing with IPv6 >>>>>> [ 2.454845] NET: Registered protocol family 17 >>>>>> [ 2.454871] NET: Registered protocol family 15 >>>>>> [ 2.455035] Bluetooth: RFCOMM socket layer initialized >>>>>> [ 2.455072] Bluetooth: RFCOMM ver 1.11 >>>>>> [ 2.455102] Bluetooth: HIDP (Human Interface Emulation) ver 1.2 >>>>>> [ 2.455117] Bluetooth: HIDP socket layer initialized >>>>>> [ 2.455161] [BT_RFKILL]: Enter rfkill_rk_init >>>>>> [ 2.455169] [WLAN_RFKILL]: Enter rfkill_wlan_init >>>>>> [ 2.455724] [WLAN_RFKILL]: Enter rfkill_wlan_probe >>>>>> [ 2.455786] [WLAN_RFKILL]: wlan_platdata_parse_dt: wifi_chip_type = >>>>>> ap6256 >>>>>> [ 2.455795] [WLAN_RFKILL]: wlan_platdata_parse_dt: enable wifi power >>>>>> control. >>>>>> [ 2.455803] [WLAN_RFKILL]: wlan_platdata_parse_dt: wifi power >>>>>> controled by gpio. >>>>>> [ 2.455828] [WLAN_RFKILL]: wlan_platdata_parse_dt: WIFI,poweren_gpio >>>>>> = 74 flags = 0. >>>>>> [ 2.455852] [WLAN_RFKILL]: wlan_platdata_parse_dt: >>>>>> WIFI,host_wake_irq = 74, flags = 0. >>>>>> [ 2.455864] [WLAN_RFKILL]: wlan_platdata_parse_dt: The ref_wifi_clk >>>>>> not found ! >>>>>> [ 2.455872] [WLAN_RFKILL]: rfkill_wlan_probe: init gpio >>>>>> [ 2.455880] [WLAN_RFKILL]: rfkill_set_wifi_bt_power: 1 >>>>>> [ 2.455888] [WLAN_RFKILL]: Exit rfkill_wlan_probe >>>>>> [ 2.456662] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: >>>>>> uart_rts_gpios = 77. >>>>>> [ 2.456693] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: >>>>>> BT,reset_gpio = 79. >>>>>> [ 2.456710] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: >>>>>> BT,wake_gpio = 81. >>>>>> [ 2.456724] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: >>>>>> BT,wake_host_irq = 80. >>>>>> [ 2.456794] [BT_RFKILL]: Request irq for bt wakeup host >>>>>> [ 2.456900] [BT_RFKILL]: ** disable irq >>>>>> [ 2.457005] [BT_RFKILL]: bt_default device registered. >>>>>> [ 2.457137] Key type dns_resolver registered >>>>>> [ 2.458535] gc8034 2-0037: driver version: 00.01.09 >>>>>> [ 2.458587] gc8034 2-0037: Failed to get power-gpios, maybe no use >>>>>> [ 2.458741] gc8034 2-0037: supply dovdd not found, using dummy >>>>>> regulator >>>>>> [ 2.458880] gc8034 2-0037: supply dvdd not found, using dummy >>>>>> regulator >>>>>> [ 2.458928] gc8034 2-0037: supply avdd not found, using dummy >>>>>> regulator >>>>>> [ 2.458979] gc8034 2-0037: lane_num(4) pixel_rate(319887360) >>>>>> [ 2.458995] gc8034 2-0037: could not get default pinstate >>>>>> [ 2.459003] gc8034 2-0037: could not get sleep pinstate >>>>>> [ 2.464279] gc8034 2-0037: gc8034 read reg:0xf0 failed ! >>>>>> [ 2.464496] gc8034 2-0037: gc8034 read reg:0xf1 failed ! >>>>>> [ 2.464510] gc8034 2-0037: Unexpected sensor id(000000), ret(-6) >>>>>> [ 2.465527] Loading compiled-in X.509 certificates >>>>>> [ 2.467269] pstore: Using crash dump compression: deflate >>>>>> [ 2.468329] rga: rga2, irq = 26, match scheduler >>>>>> [ 2.468814] rga: rga2 hardware loaded successfully, >>>>>> hw_version:3.2.63318. >>>>>> [ 2.468878] rga: rga2 probe successfully >>>>>> [ 2.469175] rga_iommu: IOMMU binding successfully, default mapping >>>>>> core[0x4] >>>>>> [ 2.469400] rga: Module initialized. v1.2.27 >>>>>> [ 2.470498] mmc0: SDHCI controller on fe310000.sdhci >>>>>> [fe310000.sdhci] using ADMA >>>>>> [ 2.493542] mmc2: queuing unknown CIS tuple 0x80 (2 bytes) >>>>>> [ 2.495364] mmc2: queuing unknown CIS tuple 0x80 (3 bytes) >>>>>> [ 2.497144] mmc2: queuing unknown CIS tuple 0x80 (3 bytes) >>>>>> [ 2.500240] mmc2: queuing unknown CIS tuple 0x80 (7 bytes) >>>>>> [ 2.503917] mmc2: queuing unknown CIS tuple 0x81 (9 bytes) >>>>>> [ 2.504631] cfg80211: Loading compiled-in X.509 certificates for >>>>>> regulatory database >>>>>> [ 2.506492] cfg80211: Loaded X.509 cert 'sforshee: >>>>>> 00b28ddf47aef9cea7' >>>>>> [ 2.507370] platform regulatory.0: Direct firmware load for >>>>>> regulatory.db failed with error -2 >>>>>> [ 2.507385] cfg80211: failed to load regulatory.db >>>>>> [ 2.507852] rockchip-pm rockchip-suspend: not set >>>>>> pwm-regulator-config >>>>>> [ 2.507873] rockchip-suspend not set sleep-mode-config for mem-lite >>>>>> [ 2.507882] rockchip-suspend not set wakeup-config for mem-lite >>>>>> [ 2.507890] rockchip-suspend not set sleep-mode-config for mem-ultra >>>>>> [ 2.507897] rockchip-suspend not set wakeup-config for mem-ultra >>>>>> [ 2.508944] I : [File] : >>>>>> drivers/gpu/arm/mali400/mali/linux/mali_kernel_linux.c; [Line] : 406; >>>>>> [Func] : mali_module_init(); svn_rev_string_from_arm of this mali_ko is >>>>>> '', rk_ko_ver is '5', built at '10:47:45', on 'Sep 8 2023'. >>>>>> [ 2.509481] Mali: >>>>>> [ 2.509485] Mali device driver loaded >>>>>> [ 2.509510] rkisp rkisp-vir0: clear unready subdev num: 1 >>>>>> [ 2.510061] rkisp-vir0: update sensor failed >>>>>> [ 2.510089] ALSA device list: >>>>>> [ 2.510098] #0: rockchip,hdmi >>>>>> [ 2.515357] mmc0: Host Software Queue enabled >>>>>> [ 2.515405] mmc0: new HS200 MMC card at address 0001 >>>>>> [ 2.516178] mmcblk0: mmc0:0001 SPeMMC 7.28 GiB >>>>>> [ 2.516462] mmcblk0boot0: mmc0:0001 SPeMMC partition 1 4.00 MiB >>>>>> [ 2.516865] mmcblk0boot1: mmc0:0001 SPeMMC partition 2 4.00 MiB >>>>>> [ 2.517172] mmcblk0rpmb: mmc0:0001 SPeMMC partition 3 4.00 MiB, >>>>>> chardev (237:0) >>>>>> [ 2.520599] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 >>>>>> [ 2.523541] <<GTP-ERR>>[_do_i2c_write:432] I2c transfer error! (-6) >>>>>> [ 2.523576] <<GTP-ERR>>[gt1x_init:2319] Reset guitar failed! >>>>>> [ 2.523584] <<GTP-INF>>[gt1x_reset_guitar:788] GTP RESET! >>>>>> [ 2.559579] mmc_host mmc2: Bus speed (slot 0) = 50000000Hz (slot req >>>>>> 50000000Hz, actual 50000000HZ div = 0) >>>>>> [ 2.563120] mmc2: new high speed SDIO card at address 0001 >>>>>> [ 2.565803] vendor storage:20190527 ret = 0 >>>>>> [ 2.593649] <<GTP-ERR>>[_do_i2c_write:432] I2c transfer error! (-6) >>>>>> [ 2.593672] <<GTP-ERR>>[gt1x_init:2319] Reset guitar failed! >>>>>> [ 2.593681] <<GTP-ERR>>[gt1x_init:2345] Init failed, use default >>>>>> setting >>>>>> [ 2.593895] <<GTP-ERR>>[_do_i2c_read:390] I2c Transfer error! (-6) >>>>>> [ 2.593908] <<GTP-ERR>>[gt1x_get_chip_type:895] I2c communication >>>>>> error. >>>>>> [ 2.593915] <<GTP-ERR>>[gt1x_init:2355] Get chip type failed! >>>>>> [ 2.594121] <<GTP-ERR>>[_do_i2c_read:390] I2c Transfer error! (-6) >>>>>> [ 2.594133] <<GTP-ERR>>[gt1x_read_version:845] Read version failed! >>>>>> [ 2.700290] <<GTP-ERR>>[_do_i2c_read:390] I2c Transfer error! (-6) >>>>>> [ 2.700310] <<GTP-ERR>>[gt1x_read_version:845] Read version failed! >>>>>> [ 2.806956] <<GTP-ERR>>[_do_i2c_read:390] I2c Transfer error! (-6) >>>>>> [ 2.806976] <<GTP-ERR>>[gt1x_read_version:845] Read version failed! >>>>>> [ 2.913371] <<GTP-INF>>[gt1x_read_version:863] IC >>>>>> VERSION:GT_000000(Patch)_0000(Mask)_00(SensorID) >>>>>> [ 2.913392] <<GTP-INF>>[gt1x_init_panel:606] Config group0 used, >>>>>> length:239 >>>>>> [ 2.913403] <<GTP-INF>>[gt1x_init_panel:657] >>>>>> X_MAX=4096,Y_MAX=4096,TRIGGER=0x01,WAKEUP_LEVEL=1 >>>>>> [ 2.913623] <<GTP-ERR>>[_do_i2c_write:432] I2c transfer error! (-6) >>>>>> [ 2.913838] <<GTP-ERR>>[_do_i2c_write:432] I2c transfer error! (-6) >>>>>> [ 2.914056] <<GTP-ERR>>[_do_i2c_write:432] I2c transfer error! (-6) >>>>>> [ 2.914272] <<GTP-ERR>>[_do_i2c_write:432] I2c transfer error! (-6) >>>>>> [ 2.914488] <<GTP-ERR>>[_do_i2c_write:432] I2c transfer error! (-6) >>>>>> [ 2.914499] <<GTP-ERR>>[gt1x_send_cfg:551] Send config failed! >>>>>> [ 2.914507] <<GTP-ERR>>[gt1x_init:2367] Init panel failed. >>>>>> [ 2.914801] <<GTP-ERR>>[gt1x_ts_probe:587] GTP init failed!!! >>>>>> [ 2.914991] Goodix-TS-GT1X: probe of 1-0014 failed with error >>>>>> -2147483644 >>>>>> [ 3.074494] EXT4-fs (mmcblk0p6): 2 orphan inodes deleted >>>>>> [ 3.074535] EXT4-fs (mmcblk0p6): recovery complete >>>>>> [ 3.078700] EXT4-fs (mmcblk0p6): mounted filesystem with ordered >>>>>> data mode. Opts: (null) >>>>>> [ 3.078794] VFS: Mounted root (ext4 filesystem) on device 179:6. >>>>>> [ 3.079676] devtmpfs: mounted >>>>>> [ 3.086768] Freeing unused kernel memory: 6592K >>>>>> [ 3.096802] Run /sbin/init as init process >>>>>> [ 3.096823] with arguments: >>>>>> [ 3.096827] /sbin/init >>>>>> [ 3.096830] with environment: >>>>>> [ 3.096833] HOME=/ >>>>>> [ 3.096836] TERM=linux >>>>>> [ 3.096838] storagemedia=emmc >>>>>> [ 3.285409] systemd[1]: System time before build time, advancing >>>>>> clock. >>>>>> [ 3.290031] systemd[1]: Failed to look up module alias 'autofs4': >>>>>> Function not implemented >>>>>> [ 4.290576] systemd-journald[198]: Received client request to flush >>>>>> runtime journal. >>>>>> [ 4.297048] systemd-journald[198]: File >>>>>> /var/log/journal/91dd2456cbf54281afa309addad7e0db/system.journal >>>>>> corrupted or uncleanly shut down, renaming and replacing. >>>>>> [ 5.712823] [BT_RFKILL]: rfkill_rk_set_power: set bt wake_host high! >>>>>> [ 5.763422] [BT_RFKILL]: rfkill_rk_set_power: set bt wake_host input! >>>>>> [ 5.763492] [BT_RFKILL]: ENABLE UART_RTS >>>>>> [ 5.870061] [BT_RFKILL]: DISABLE UART_RTS >>>>>> [ 5.870142] [BT_RFKILL]: bt turn on power >>>>>> [ 5.870175] [BT_RFKILL]: Request irq for bt wakeup host >>>>>> [ 5.870218] [BT_RFKILL]: ** disable irq >>>>>> [ 7.938573] EXT4-fs (mmcblk0p7): mounted filesystem with ordered >>>>>> data mode. Opts: (null) >>>>>> [ 8.001872] EXT4-fs (mmcblk0p8): mounted filesystem with ordered >>>>>> data mode. Opts: (null) >>>>>> [ 8.883246] [dhd] STATIC-MSG) dhd_static_buf_init : 101.10.361.18 >>>>>> (wlan=r892223-20220519-1) >>>>>> [ 8.883702] [dhd] STATIC-MSG) dhd_init_wlan_mem : prealloc ok for >>>>>> index 0: 8131584(7941K) >>>>>> [ 9.450664] bcmdhd: loading out-of-tree module taints kernel. >>>>>> [ 9.464195] [dhd] _dhd_module_init: in Dongle Host Driver, version >>>>>> 101.10.361.25 (wlan=r892223-20220929-2) >>>>>> >>>>>> /home/gtc/geniatech/xpi-3566-zero/external/rkwifibt/drivers/bcmdhd >>>>>> compiled on Sep 25 2023 at 16:08:41 >>>>>> >>>>>> [ 9.464339] [WLAN_RFKILL]: rockchip_wifi_get_oob_irq: Enter >>>>>> [ 9.464434] [dhd] dhd_wlan_init_gpio: WL_HOST_WAKE=-1, oob_irq=74, >>>>>> oob_irq_flags=0x4 >>>>>> [ 9.464447] [dhd] dhd_wlan_init_gpio: WL_REG_ON=-1 >>>>>> [ 9.464455] [dhd] STATIC-MSG) dhd_static_buf_init : 101.10.361.25 >>>>>> (wlan=r892223-20220928-2) >>>>>> [ 9.465021] [dhd] STATIC-MSG) dhd_init_wlan_mem : prealloc ok for >>>>>> index 0: 8138752(7948K) >>>>>> [ 9.465047] [dhd] dhd_wifi_platform_load: Enter >>>>>> [ 9.465056] [dhd] Power-up adapter 'DHD generic adapter' >>>>>> [ 9.465308] [dhd] dummy_probe: enter >>>>>> [ 9.469572] [dhd] dummy_probe: enter >>>>>> [ 9.475102] [dhd] wifi_platform_set_power = 1, delay: 200 msec >>>>>> [ 9.475135] [dhd] ======== PULL WL_REG_ON(-1) HIGH! ======== >>>>>> [ 9.475145] [WLAN_RFKILL]: rockchip_wifi_power: 1 >>>>>> [ 9.475155] [WLAN_RFKILL]: rockchip_wifi_power: toggle = false >>>>>> [ 9.575560] file system registered >>>>>> [ 9.580048] [WLAN_RFKILL]: wifi turn on power [GPIO74-1] >>>>>> [ 9.797002] read descriptors >>>>>> [ 9.797132] read strings >>>>>> [ 9.887037] [dhd] wifi_platform_bus_enumerate device present 1 >>>>>> [ 9.887086] [dhd] ======== Card detection to detect SDIO card! >>>>>> ======== >>>>>> [ 9.903556] [dhd] bcmsdh_register: register client driver >>>>>> [ 9.910401] [dhd] bcmsdh_sdmmc_probe: Enter num=1 >>>>>> [ 9.915945] [dhd] bcmsdh_sdmmc_probe: Enter num=2 >>>>>> [ 9.915995] [dhd] bus num (host idx)=2, slot num (rca)=1 >>>>>> [ 9.916006] [dhd] found adapter info 'DHD generic adapter' >>>>>> [ 9.916019] [dhd] STATIC-MSG) dhd_wlan_mem_prealloc : section 3, >>>>>> size 139264 >>>>>> [ 9.916058] [dhd] succeed to alloc static buf >>>>>> [ 9.916066] [dhd] STATIC-MSG) dhd_wlan_mem_prealloc : section 4, >>>>>> size 0 >>>>>> [ 9.916220] [dhd] sdioh_attach: set sd_f2_blocksize 256 >>>>>> [ 9.916769] [dhd] sdioh_attach: sd clock rate = 50000000 >>>>>> [ 9.922369] [dhd] dhdsdio_probe : no mutex held >>>>>> [ 9.922420] [dhd] dhdsdio_probe : set mutex lock >>>>>> [ 9.924390] [dhd] F1 signature read @0x18000000=0x15294345 >>>>>> [ 9.931550] [dhd] F1 signature OK, socitype:0x1 chip:0x4345 rev:0x9 >>>>>> pkg:0x2 >>>>>> [ 9.932967] [dhd] DHD: dongle ram size is set to 819200(orig 819200) >>>>>> at 0x198000 >>>>>> [ 9.933210] [dhd] STATIC-MSG) dhd_wlan_mem_prealloc : section 7, >>>>>> size 32600 >>>>>> [ 9.933262] [dhd] dhd_conf_set_chiprev : devid=0xa9bf, chip=0x4345, >>>>>> chiprev=9 >>>>>> [ 9.934698] [dhd] STATIC-MSG) dhd_wlan_mem_prealloc : section 0, >>>>>> size 10320 >>>>>> [ 9.936446] [dhd] STATIC-MSG) dhd_wlan_mem_prealloc : section 5, >>>>>> size 65536 >>>>>> [ 9.945095] [dhd] STATIC-MSG) dhd_wlan_mem_prealloc : section 19, >>>>>> size 65688 >>>>>> [ 9.945253] [dhd] STATIC-MSG) dhd_wlan_mem_prealloc : section 20, >>>>>> size 262144 >>>>>> [ 9.945335] [dhd] STATIC-MSG) dhd_wlan_mem_prealloc : section 22, >>>>>> size 65536 >>>>>> [ 9.948104] [dhd] dhd_attach(): thread:dhd_watchdog_thread:3b8 >>>>>> started >>>>>> [ 9.956868] [dhd] dhd_attach(): thread:dhd_dpc:3b9 started >>>>>> [ 9.960645] [dhd] dhd_attach(): thread:dhd_rxf:3bb started >>>>>> [ 9.960697] [dhd] dhd_deferred_work_init: work queue initialized >>>>>> [ 9.960711] [dhd] dhd_tcpack_suppress_set: TCP ACK Suppress mode 0 >>>>>> -> mode 2 >>>>>> [ 9.960719] [dhd] dhd_tcpack_suppress_set: TCPACK_INFO_MAXNUM=10, >>>>>> TCPDATA_INFO_MAXNUM=10 >>>>>> [ 9.960784] [dhd] sdioh_cis_read: func_cis_ptr[0]=0x10ac >>>>>> [ 9.975873] [dhd] STATIC-MSG) dhd_wlan_mem_prealloc : section 1, >>>>>> size 10300 >>>>>> [ 9.975925] [dhd] STATIC-MSG) dhd_wlan_mem_prealloc : section 2, >>>>>> size 65536 >>>>>> [ 9.976080] [dhd] dhdsdio_probe_init: making DHD_BUS_DOWN >>>>>> [ 9.976283] [dhd] Dongle Host Driver, version 101.10.361.25 >>>>>> (wlan=r892223-20220929-2) >>>>>> >>>>>> /home/gtc/geniatech/xpi-3566-zero/external/rkwifibt/drivers/bcmdhd >>>>>> compiled on Sep 25 2023 at 16:08:41 >>>>>> >>>>>> [ 9.983502] [dhd] Register interface [wlan0] MAC: b8:2d:xxxxxx >>>>>> >>>>>> [ 9.984030] [dhd] [wlan0] wl_android_wifi_off : in g_wifi_on=1, >>>>>> on_failure=1 >>>>>> [ 9.984062] [dhd] dhd_bus_devreset: == Power OFF == >>>>>> [ 9.985260] [dhd] dhd_bus_stop: making DHD_BUS_DOWN >>>>>> [ 9.985333] [dhd] bcmsdh_oob_intr_unregister: Enter >>>>>> [ 9.985343] [dhd] bcmsdh_oob_intr_unregister: irq is not registered >>>>>> [ 9.985361] [dhd] dhd_bus_devreset: making dhdpub up FALSE >>>>>> [ 9.985371] [dhd] dhd_txglom_enable: enable 0 >>>>>> [ 9.985380] [dhd] dhd_bus_devreset: making DHD_BUS_DOWN >>>>>> [ 9.985522] [dhd] wifi_platform_set_power = 0, delay: 0 msec >>>>>> [ 9.985536] [dhd] ======== PULL WL_REG_ON(-1) LOW! ======== >>>>>> [ 9.985545] [WLAN_RFKILL]: rockchip_wifi_power: 0 >>>>>> [ 9.985554] [WLAN_RFKILL]: rockchip_wifi_power: toggle = false >>>>>> [ 9.985561] wifi power off >>>>>> [ 10.051825] [dhd] dhd_pri_open : probe is already running! return. >>>>>> [ 10.074460] [dhd] dhd_pri_open : probe is already running! return. >>>>>> [ 10.084465] [dhd] dhd_pri_open : probe is already running! return. >>>>>> [ 10.090137] [WLAN_RFKILL]: wifi shut off power [GPIO74-0] >>>>>> [ 10.090186] [dhd] [wlan0] wl_android_wifi_off : out >>>>>> [ 10.090201] [dhd] dhdsdio_probe : mutex is released. >>>>>> [ 10.090516] [dhd] _dhd_module_init: Exit err=0 >>>>>> [ 10.164305] [BT_RFKILL]: bt shut off power >>>>>> [ 10.203877] [BT_RFKILL]: rfkill_rk_set_power: set bt wake_host high! >>>>>> [ 10.256770] [BT_RFKILL]: rfkill_rk_set_power: set bt wake_host input! >>>>>> [ 10.256850] [BT_RFKILL]: ENABLE UART_RTS >>>>>> [ 10.363488] [BT_RFKILL]: DISABLE UART_RTS >>>>>> [ 10.363579] [BT_RFKILL]: bt turn on power >>>>>> [ 10.363613] [BT_RFKILL]: Request irq for bt wakeup host >>>>>> [ 10.363658] [BT_RFKILL]: ** disable irq >>>>>> [ 10.406005] of_dma_request_slave_channel: dma-names property of node >>>>>> '/serial@fe650000' missing or empty >>>>>> [ 10.408347] dw-apb-uart fe650000.serial: failed to request DMA, use >>>>>> interrupt mode >>>>>> [ 10.483792] [BT_RFKILL]: bt shut off power >>>>>> [ 11.533061] [BT_RFKILL]: rfkill_rk_set_power: set bt wake_host high! >>>>>> [ 11.583473] [BT_RFKILL]: rfkill_rk_set_power: set bt wake_host input! >>>>>> [ 11.583551] [BT_RFKILL]: ENABLE UART_RTS >>>>>> [ 11.690085] [BT_RFKILL]: DISABLE UART_RTS >>>>>> [ 11.690169] [BT_RFKILL]: bt turn on power >>>>>> [ 11.690203] [BT_RFKILL]: Request irq for bt wakeup host >>>>>> [ 11.690245] [BT_RFKILL]: ** disable irq >>>>>> [ 13.920568] systemd-journald[198]: File >>>>>> /var/log/journal/91dd2456cbf54281afa309addad7e0db/user-1000.journal >>>>>> corrupted or uncleanly shut down, renaming and replacing. >>>>>> [ 14.000271] Freeing drm_logo memory: 736K >>>>>> [ 15.527834] ttyFIQ ttyFIQ0: tty_port_close_start: tty->count = 1 >>>>>> port count = 2 >>>>>> [ 20.401475] [dhd] dhd_pri_open : no mutex held >>>>>> [ 20.401613] [dhd] dhd_pri_open : set mutex lock >>>>>> [ 20.401625] [dhd] [wlan0] dhd_open : Enter >>>>>> [ 20.401635] [dhd] Dongle Host Driver, version 101.10.361.25 >>>>>> (wlan=r892223-20220929-2) >>>>>> >>>>>> /home/gtc/geniatech/xpi-3566-zero/external/rkwifibt/drivers/bcmdhd >>>>>> compiled on Sep 25 2023 at 16:08:41 >>>>>> >>>>>> [ 20.401651] [dhd] dhd_open: ######### called for ifidx=0 ######### >>>>>> [ 20.401669] [dhd] [wlan0] wl_android_wifi_on : in g_wifi_on=0 >>>>>> [ 20.401679] [dhd] wifi_platform_set_power = 1, delay: 200 msec >>>>>> [ 20.401686] [dhd] ======== PULL WL_REG_ON(-1) HIGH! ======== >>>>>> [ 20.401694] [WLAN_RFKILL]: rockchip_wifi_power: 1 >>>>>> [ 20.401703] [WLAN_RFKILL]: rockchip_wifi_power: toggle = false >>>>>> [ 20.506800] [WLAN_RFKILL]: wifi turn on power [GPIO74-1] >>>>>> [ 20.813369] [dhd] sdio_sw_reset: call mmc_hw_reset >>>>>> [ 20.826812] mmc_host mmc2: Bus speed (slot 0) = 375000Hz (slot req >>>>>> 400000Hz, actual 375000HZ div = 0) >>>>>> [ 20.857057] mmc2: queuing unknown CIS tuple 0x80 (2 bytes) >>>>>> [ 20.858825] mmc2: queuing unknown CIS tuple 0x80 (3 bytes) >>>>>> [ 20.860532] mmc2: queuing unknown CIS tuple 0x80 (3 bytes) >>>>>> [ 20.863836] mmc2: queuing unknown CIS tuple 0x80 (7 bytes) >>>>>> [ 20.867573] mmc2: queuing unknown CIS tuple 0x81 (9 bytes) >>>>>> [ 20.925517] mmc_host mmc2: Bus speed (slot 0) = 50000000Hz (slot req >>>>>> 50000000Hz, actual 50000000HZ div = 0) >>>>>> [ 20.925667] [dhd] sdioh_start: set sd_f2_blocksize 256 >>>>>> [ 20.925981] [dhd] dhd_bus_devreset: == Power ON == >>>>>> [ 20.926104] [dhd] F1 signature read @0x18000000=0x15294345 >>>>>> [ 20.929772] [dhd] F1 signature OK, socitype:0x1 chip:0x4345 rev:0x9 >>>>>> pkg:0x2 >>>>>> [ 20.930521] [dhd] DHD: dongle ram size is set to 819200(orig 819200) >>>>>> at 0x198000 >>>>>> [ 20.930587] [dhd] dhd_bus_devreset: making DHD_BUS_DOWN >>>>>> [ 20.930648] [dhd] dhdsdio_probe_init: making DHD_BUS_DOWN >>>>>> [ 20.930825] [dhd] dhd_conf_set_path_params : Final >>>>>> fw_path=/vendor/etc/firmware/fw_bcm43456c5_ag.bin >>>>>> [ 20.930835] [dhd] dhd_conf_set_path_params : Final >>>>>> nv_path=/vendor/etc/firmware/nvram_ap6256.txt >>>>>> [ 20.930843] [dhd] dhd_conf_set_path_params : Final >>>>>> clm_path=/vendor/etc/firmware/clm_bcm43456c5_ag.blob >>>>>> [ 20.930850] [dhd] dhd_conf_set_path_params : Final >>>>>> conf_path=/vendor/etc/firmware/config.txt >>>>>> [ 20.931076] [dhd] dhd_os_open_image1: >>>>>> /vendor/etc/firmware/config.txt (240 bytes) open success >>>>>> [ 20.931522] [dhd] dhd_conf_read_pm_params : PM = 0 >>>>>> [ 20.931539] [dhd] dhd_conf_read_pm_params : pm_in_suspend = 2 >>>>>> [ 20.931560] [dhd] dhd_conf_read_others : keep_alive_period = 120000 >>>>>> [ 20.931573] [dhd] dhd_conf_read_others : garp = 1 >>>>>> [ 20.931585] [dhd] dhd_conf_read_pm_params : suspend_bcn_li_dtim = 10 >>>>>> [ 20.931601] [dhd] dhd_conf_read_others : wl_preinit = >>>>>> pm2_sleep_ret=20 >>>>>> [ 20.931614] [dhd] dhd_conf_read_pkt_filter : pkt_filter_del id = 100 >>>>>> 102 103 104 105 107 >>>>>> [ 20.931641] [dhd] dhd_conf_read_pkt_filter : pkt_filter_add[0][] = >>>>>> 142 0 0 77 0xffffffffffffffffffffffffffffff >>>>>> 0x2F6465766963652F77616B6575702F >>>>>> [ 20.932260] [dhd] dhd_os_open_image1: >>>>>> /vendor/etc/firmware/fw_bcm43456c5_ag.bin (508373 bytes) open success >>>>>> [ 21.012945] [dhd] dhd_os_open_image1: >>>>>> /vendor/etc/firmware/nvram_ap6256.txt (2424 bytes) open success >>>>>> [ 21.013594] [dhd] #AP6256_NVRAM_V1.2_09202018.txt >>>>>> [ 21.014325] [dhd] dhdsdio_write_vars: Download, Upload and compare >>>>>> of NVRAM succeeded. >>>>>> [ 21.093111] [dhd] dhd_bus_init: enable 0x06, ready 0x06 (waited 0us) >>>>>> [ 21.094157] [dhd] bcmsdh_oob_intr_register: HW_OOB irq=74 flags=0x4 >>>>>> [ 21.096264] [dhd] wlc_ver_major 3, wlc_ver_minor 0 >>>>>> [ 21.097448] [dhd] dhd_preinit_ioctls: preinit_status IOVAR not >>>>>> supported, use legacy preinit >>>>>> [ 21.097495] [dhd] dhd_tcpack_suppress_set: TCP ACK Suppress mode 2 >>>>>> -> mode 1 >>>>>> [ 21.097505] [dhd] dhd_tcpack_suppress_set: TCPACK_INFO_MAXNUM=10, >>>>>> TCPDATA_INFO_MAXNUM=10 >>>>>> [ 21.098671] [dhd] dhd_legacy_preinit_ioctls: use firmware generated >>>>>> mac_address b8:2d:xxxxx >>>>>> [ 21.098774] [dhd] dhd_apply_default_clm: Ignore clm file >>>>>> /vendor/etc/firmware/clm_bcm43456c5_ag.blob >>>>>> [ 21.101446] [dhd] Firmware up: op_mode=0x0005, MAC=b8:2d:xxxxx >>>>>> [ 21.107634] [dhd] dhd_legacy_preinit_ioctls: event_log_max_sets: 31 >>>>>> ret: -23 >>>>>> [ 21.110968] [dhd] arp_enable:1 arp_ol:0 >>>>>> [ 21.111012] [dhd] dhd_conf_add_pkt_filter : 142 0 0 77 >>>>>> 0xffffffffffffffffffffffffffffff 0x2F6465766963652F77616B6575702F >>>>>> [ 21.117056] [dhd] Driver: 101.10.361.25 (wlan=r892223-20220929-2) >>>>>> [dhd] Firmware: wl0: Sep 7 2018 14:33:37 version >>>>>> 7.45.96.27 (42b546f@shgit) (r) FWID 01-c958c084 es7.c5.n4.a3 >>>>>> [dhd] CLM: 9.2.9 (2016-02-03 04:34:31) >>>>>> [ 21.117574] [dhd] dhd_txglom_enable: enable 1 >>>>>> [ 21.117622] [dhd] dhd_conf_set_txglom_params : txglom_mode=copy >>>>>> [ 21.117633] [dhd] dhd_conf_set_txglom_params : txglomsize=36, >>>>>> deferred_tx_len=0 >>>>>> [ 21.117640] [dhd] dhd_conf_set_txglom_params : txinrx_thres=128, >>>>>> dhd_txminmax=-1 >>>>>> [ 21.117648] [dhd] dhd_conf_set_txglom_params : tx_max_offset=0, >>>>>> txctl_tmo_fix=300 >>>>>> [ 21.117661] [dhd] dhd_conf_get_disable_proptx : fw_proptx=1, >>>>>> disable_proptx=-1 >>>>>> [ 21.119224] [dhd] dhd_wlfc_hostreorder_init(): successful bdcv2 tlv >>>>>> signaling, 64 >>>>>> [ 21.122689] [dhd] dhd_pno_init: Support Android Location Service >>>>>> [ 21.148163] [dhd] dhd_legacy_preinit_ioctls: Failed to get preserve >>>>>> log # ! >>>>>> [ 21.169492] [dhd] dhd_conf_map_country_list : CN/38 >>>>>> [ 21.169543] [dhd] dhd_conf_set_country : set country CN, revision 38 >>>>>> [ 21.172072] [dhd] CFG80211-ERROR) wl_cfg80211_event : Event handler >>>>>> is not created (WLC_E_COUNTRY_CODE_CHANGED) >>>>>> [ 21.172409] [dhd] dhd_conf_set_country : Country code: CN (CN/38) >>>>>> [ 21.179949] [dhd] [wlan0] wl_android_wifi_on : Success >>>>>> [ 21.233299] [dhd] CFG80211-ERROR) init_roam_cache : roamscan_mode >>>>>> iovar failed. -23 >>>>>> [ 21.233369] [dhd] CFG80211-ERROR) wl_cfg80211_up : Failed to enable >>>>>> RCC. >>>>>> [ 21.234407] [dhd] [wlan0] dhd_open : Exit ret=0 >>>>>> [ 21.234429] [dhd] [wlan0] dhd_pri_open : tx queue started >>>>>> [ 21.234437] [dhd] dhd_pri_open : mutex is released. >>>>>> [ 21.301397] [dhd] P2P interface registered >>>>>> [ 21.331052] [dhd] WLC_E_IF: NO_IF set, event Ignored >>>>>> >>>>>> [ 21.332373] [dhd] P2P interface started >>>>>> [ 21.394531] [dhd] [wlan0] wl_run_escan : LEGACY_SCAN sync ID: 0, >>>>>> bssidx: 0 >>>>>> [ 25.399791] [dhd] [wlan0] wl_run_escan : LEGACY_SCAN sync ID: 1, >>>>>> bssidx: 0 >>>>>> [ 25.896769] usb 1-1: new full-speed USB device number 2 using >>>>>> xhci-hcd >>>>>> [ 26.040641] usb 1-1: New USB device found, idVendor=046d, >>>>>> idProduct=c52b, bcdDevice=24.11 >>>>>> [ 26.040703] usb 1-1: New USB device strings: Mfr=1, Product=2, >>>>>> SerialNumber=0 >>>>>> [ 26.040714] usb 1-1: Product: USB Receiver >>>>>> [ 26.040723] usb 1-1: Manufacturer: Logitech >>>>>> [ 26.078789] input: Logitech USB Receiver as >>>>>> /devices/platform/usbhost/fd000000.dwc3/xhci-hcd.4.auto/usb1/1-1/1-1:1.0/0003:046D:C52B.0001/input/input1 >>>>>> [ 26.134907] hid-generic 0003:046D:C52B.0001: input,hidraw0: USB HID >>>>>> v1.11 Keyboard [Logitech USB Receiver] on usb-xhci-hcd.4.auto-1/input0 >>>>>> [ 26.150920] input: Logitech USB Receiver Mouse as >>>>>> /devices/platform/usbhost/fd000000.dwc3/xhci-hcd.4.auto/usb1/1-1/1-1:1.1/0003:046D:C52B.0002/input/input2 >>>>>> [ 26.151935] input: Logitech USB Receiver Consumer Control as >>>>>> /devices/platform/usbhost/fd000000.dwc3/xhci-hcd.4.auto/usb1/1-1/1-1:1.1/0003:046D:C52B.0002/input/input3 >>>>>> [ 26.207483] input: Logitech USB Receiver System Control as >>>>>> /devices/platform/usbhost/fd000000.dwc3/xhci-hcd.4.auto/usb1/1-1/1-1:1.1/0003:046D:C52B.0002/input/input4 >>>>>> [ 26.208529] hid-generic 0003:046D:C52B.0002: input,hiddev96,hidraw1: >>>>>> USB HID v1.11 Mouse [Logitech USB Receiver] on >>>>>> usb-xhci-hcd.4.auto-1/input1 >>>>>> [ 26.222063] hid-generic 0003:046D:C52B.0003: hiddev97,hidraw2: USB >>>>>> HID v1.11 Device [Logitech USB Receiver] on usb-xhci-hcd.4.auto-1/input2 >>>>>> [ 30.397602] [dhd] [wlan0] wl_run_escan : LEGACY_SCAN sync ID: 2, >>>>>> bssidx: 0 >>>>>> [ 33.440143] vcc3v3_lcd1_n: disabling >>>>>> [ 37.403274] [dhd] [wlan0] wl_run_escan : LEGACY_SCAN sync ID: 3, >>>>>> bssidx: 0 >>>>>> [ 40.444368] usb 1-1: USB disconnect, device number 2 >>>>>> [ 47.400586] [dhd] [wlan0] wl_run_escan : LEGACY_SCAN sync ID: 4, >>>>>> bssidx: 0 >>>>>> [ 57.310046] usb 1-1: new high-speed USB device number 3 using >>>>>> xhci-hcd >>>>>> [ 57.450395] usb 1-1: New USB device found, idVendor=1a40, >>>>>> idProduct=0101, bcdDevice= 1.00 >>>>>> [ 57.450437] usb 1-1: New USB device strings: Mfr=0, Product=1, >>>>>> SerialNumber=0 >>>>>> [ 57.450448] usb 1-1: Product: USB2.0 HUB >>>>>> [ 57.492389] hub 1-1:1.0: USB hub found >>>>>> [ 57.492541] hub 1-1:1.0: 4 ports detected >>>>>> [ 57.870058] usb 1-1.1: new full-speed USB device number 4 using >>>>>> xhci-hcd >>>>>> [ 58.063782] usb 1-1.1: New USB device found, idVendor=046d, >>>>>> idProduct=c52b, bcdDevice=24.11 >>>>>> [ 58.063821] usb 1-1.1: New USB device strings: Mfr=1, Product=2, >>>>>> SerialNumber=0 >>>>>> [ 58.063831] usb 1-1.1: Product: USB Receiver >>>>>> [ 58.063839] usb 1-1.1: Manufacturer: Logitech >>>>>> [ 58.168459] input: Logitech USB Receiver as >>>>>> /devices/platform/usbhost/fd000000.dwc3/xhci-hcd.4.auto/usb1/1-1/1-1.1/1-1.1:1.0/0003:046D:C52B.0004/input/input6 >>>>>> [ 58.224158] hid-generic 0003:046D:C52B.0004: input,hidraw0: USB HID >>>>>> v1.11 Keyboard [Logitech USB Receiver] on usb-xhci-hcd.4.auto-1.1/input0 >>>>>> [ 58.235027] input: Logitech USB Receiver Mouse as >>>>>> /devices/platform/usbhost/fd000000.dwc3/xhci-hcd.4.auto/usb1/1-1/1-1.1/1-1.1:1.1/0003:046D:C52B.0005/input/input7 >>>>>> [ 58.235451] input: Logitech USB Receiver Consumer Control as >>>>>> /devices/platform/usbhost/fd000000.dwc3/xhci-hcd.4.auto/usb1/1-1/1-1.1/1-1.1:1.1/0003:046D:C52B.0005/input/input8 >>>>>> [ 58.290565] input: Logitech USB Receiver System Control as >>>>>> /devices/platform/usbhost/fd000000.dwc3/xhci-hcd.4.auto/usb1/1-1/1-1.1/1-1.1:1.1/0003:046D:C52B.0005/input/input9 >>>>>> [ 58.291040] hid-generic 0003:046D:C52B.0005: input,hiddev96,hidraw1: >>>>>> USB HID v1.11 Mouse [Logitech USB Receiver] on >>>>>> usb-xhci-hcd.4.auto-1.1/input1 >>>>>> [ 58.302615] hid-generic 0003:046D:C52B.0006: hiddev97,hidraw2: USB >>>>>> HID v1.11 Device [Logitech USB Receiver] on >>>>>> usb-xhci-hcd.4.auto-1.1/input2 >>>>>> [ 61.410435] [dhd] [wlan0] wl_run_escan : LEGACY_SCAN sync ID: 5, >>>>>> bssidx: 0 >>>>>> [ 62.260152] usb 1-1.1: USB disconnect, device number 4 >>>>>> [ 62.733334] usb 1-1.1: new full-speed USB device number 5 using >>>>>> xhci-hcd >>>>>> [ 62.926727] usb 1-1.1: New USB device found, idVendor=046d, >>>>>> idProduct=c52b, bcdDevice=24.11 >>>>>> [ 62.926764] usb 1-1.1: New USB device strings: Mfr=1, Product=2, >>>>>> SerialNumber=0 >>>>>> [ 62.926774] usb 1-1.1: Product: USB Receiver >>>>>> [ 62.926782] usb 1-1.1: Manufacturer: Logitech >>>>>> [ 63.032694] input: Logitech USB Receiver as >>>>>> /devices/platform/usbhost/fd000000.dwc3/xhci-hcd.4.auto/usb1/1-1/1-1.1/1-1.1:1.0/0003:046D:C52B.0007/input/input11 >>>>>> [ 63.088204] hid-generic 0003:046D:C52B.0007: input,hidraw0: USB HID >>>>>> v1.11 Keyboard [Logitech USB Receiver] on usb-xhci-hcd.4.auto-1.1/input0 >>>>>> [ 63.094013] input: Logitech USB Receiver Mouse as >>>>>> /devices/platform/usbhost/fd000000.dwc3/xhci-hcd.4.auto/usb1/1-1/1-1.1/1-1.1:1.1/0003:046D:C52B.0008/input/input12 >>>>>> [ 63.094541] input: Logitech USB Receiver Consumer Control as >>>>>> /devices/platform/usbhost/fd000000.dwc3/xhci-hcd.4.auto/usb1/1-1/1-1.1/1-1.1:1.1/0003:046D:C52B.0008/input/input13 >>>>>> [ 63.150590] input: Logitech USB Receiver System Control as >>>>>> /devices/platform/usbhost/fd000000.dwc3/xhci-hcd.4.auto/usb1/1-1/1-1.1/1-1.1:1.1/0003:046D:C52B.0008/input/input14 >>>>>> [ 63.151342] hid-generic 0003:046D:C52B.0008: input,hiddev96,hidraw1: >>>>>> USB HID v1.11 Mouse [Logitech USB Receiver] on >>>>>> usb-xhci-hcd.4.auto-1.1/input1 >>>>>> [ 63.156209] hid-generic 0003:046D:C52B.0009: hiddev97,hidraw2: USB >>>>>> HID v1.11 Device [Logitech USB Receiver] on >>>>>> usb-xhci-hcd.4.auto-1.1/input2 >>>>>> [ 63.466730] usb 1-1.4: new low-speed USB device number 6 using >>>>>> xhci-hcd >>>>>> [ 63.662293] usb 1-1.4: New USB device found, idVendor=046d, >>>>>> idProduct=c31c, bcdDevice=64.02 >>>>>> [ 63.662330] usb 1-1.4: New USB device strings: Mfr=1, Product=2, >>>>>> SerialNumber=0 >>>>>> [ 63.662340] usb 1-1.4: Product: USB Keyboard >>>>>> [ 63.662349] usb 1-1.4: Manufacturer: Logitech >>>>>> [ 63.738680] input: Logitech USB Keyboard as >>>>>> /devices/platform/usbhost/fd000000.dwc3/xhci-hcd.4.auto/usb1/1-1/1-1.4/1-1.4:1.0/0003:046D:C31C.000A/input/input16 >>>>>> [ 63.794431] hid-generic 0003:046D:C31C.000A: input,hidraw3: USB HID >>>>>> v1.10 Keyboard [Logitech USB Keyboard] on usb-xhci-hcd.4.auto-1.4/input0 >>>>>> [ 63.802956] input: Logitech USB Keyboard Consumer Control as >>>>>> /devices/platform/usbhost/fd000000.dwc3/xhci-hcd.4.auto/usb1/1-1/1-1.4/1-1.4:1.1/0003:046D:C31C.000B/input/input17 >>>>>> [ 63.857239] input: Logitech USB Keyboard System Control as >>>>>> /devices/platform/usbhost/fd000000.dwc3/xhci-hcd.4.auto/usb1/1-1/1-1.4/1-1.4:1.1/0003:046D:C31C.000B/input/input18 >>>>>> [ 63.858002] hid-generic 0003:046D:C31C.000B: input,hiddev98,hidraw4: >>>>>> USB HID v1.10 Device [Logitech USB Keyboard] on >>>>>> usb-xhci-hcd.4.auto-1.4/input1 >>>>>> [ 81.401443] [dhd] [wlan0] wl_run_escan : LEGACY_SCAN sync ID: 6, >>>>>> bssidx: 0 >>>>>> [ 100.148159] usb 1-1.4: USB disconnect, device number 6 >>>>>> [ 104.500151] usb 1-1.1: USB disconnect, device number 5 >>>>>> [ 105.000040] usb 1-1.1: new full-speed USB device number 7 using >>>>>> xhci-hcd >>>>>> [ 105.176859] usb 1-1.1: Device not responding to setup address. >>>>>> [ 105.383527] usb 1-1.1: Device not responding to setup address. >>>>>> [ 105.590046] usb 1-1.1: device not accepting address 7, error -71 >>>>>> [ 105.970048] usb 1-1.1: new full-speed USB device number 8 using >>>>>> xhci-hcd >>>>>> [ 106.163750] usb 1-1.1: New USB device found, idVendor=046d, >>>>>> idProduct=c52b, bcdDevice=24.11 >>>>>> [ 106.163789] usb 1-1.1: New USB device strings: Mfr=1, Product=2, >>>>>> SerialNumber=0 >>>>>> [ 106.163799] usb 1-1.1: Product: USB Receiver >>>>>> [ 106.163808] usb 1-1.1: Manufacturer: Logitech >>>>>> [ 106.296734] input: Logitech USB Receiver as >>>>>> /devices/platform/usbhost/fd000000.dwc3/xhci-hcd.4.auto/usb1/1-1/1-1.1/1-1.1:1.0/0003:046D:C52B.000C/input/input19 >>>>>> [ 106.354122] hid-generic 0003:046D:C52B.000C: input,hidraw0: USB HID >>>>>> v1.11 Keyboard [Logitech USB Receiver] on usb-xhci-hcd.4.auto-1.1/input0 >>>>>> [ 106.359457] input: Logitech USB Receiver Mouse as >>>>>> /devices/platform/usbhost/fd000000.dwc3/xhci-hcd.4.auto/usb1/1-1/1-1.1/1-1.1:1.1/0003:046D:C52B.000D/input/input20 >>>>>> [ 106.359906] input: Logitech USB Receiver Consumer Control as >>>>>> /devices/platform/usbhost/fd000000.dwc3/xhci-hcd.4.auto/usb1/1-1/1-1.1/1-1.1:1.1/0003:046D:C52B.000D/input/input21 >>>>>> [ 106.413872] input: Logitech USB Receiver System Control as >>>>>> /devices/platform/usbhost/fd000000.dwc3/xhci-hcd.4.auto/usb1/1-1/1-1.1/1-1.1:1.1/0003:046D:C52B.000D/input/input22 >>>>>> [ 106.414454] hid-generic 0003:046D:C52B.000D: input,hiddev96,hidraw1: >>>>>> USB HID v1.11 Mouse [Logitech USB Receiver] on >>>>>> usb-xhci-hcd.4.auto-1.1/input1 >>>>>> [ 106.418857] hid-generic 0003:046D:C52B.000E: hiddev97,hidraw2: USB >>>>>> HID v1.11 Device [Logitech USB Receiver] on >>>>>> usb-xhci-hcd.4.auto-1.1/input2 >>>>>> [ 106.729981] usb 1-1.4: new low-speed USB device number 9 using >>>>>> xhci-hcd >>>>>> [ 106.925618] usb 1-1.4: New USB device found, idVendor=046d, >>>>>> idProduct=c31c, bcdDevice=64.02 >>>>>> [ 106.925655] usb 1-1.4: New USB device strings: Mfr=1, Product=2, >>>>>> SerialNumber=0 >>>>>> [ 106.925665] usb 1-1.4: Product: USB Keyboard >>>>>> [ 106.925673] usb 1-1.4: Manufacturer: Logitech >>>>>> [ 107.002451] input: Logitech USB Keyboard as >>>>>> /devices/platform/usbhost/fd000000.dwc3/xhci-hcd.4.auto/usb1/1-1/1-1.4/1-1.4:1.0/0003:046D:C31C.000F/input/input24 >>>>>> [ 107.057502] hid-generic 0003:046D:C31C.000F: input,hidraw3: USB HID >>>>>> v1.10 Keyboard [Logitech USB Keyboard] on usb-xhci-hcd.4.auto-1.4/input0 >>>>>> [ 107.065863] input: Logitech USB Keyboard Consumer Control as >>>>>> /devices/platform/usbhost/fd000000.dwc3/xhci-hcd.4.auto/usb1/1-1/1-1.4/1-1.4:1.1/0003:046D:C31C.0010/input/input25 >>>>>> [ 107.120485] input: Logitech USB Keyboard System Control as >>>>>> /devices/platform/usbhost/fd000000.dwc3/xhci-hcd.4.auto/usb1/1-1/1-1.4/1-1.4:1.1/0003:046D:C31C.0010/input/input26 >>>>>> [ 107.121039] hid-generic 0003:046D:C31C.0010: input,hiddev98,hidraw4: >>>>>> USB HID v1.10 Device [Logitech USB Keyboard] on >>>>>> usb-xhci-hcd.4.auto-1.4/input1 >>>>>> [ 110.423651] [dhd] [wlan0] wl_run_escan : LEGACY_SCAN sync ID: 7, >>>>>> bssidx: 0 >>>>>> [ 153.400865] [dhd] [wlan0] wl_run_escan : LEGACY_SCAN sync ID: 8, >>>>>> bssidx: 0 >>>>>> [ 217.401022] [dhd] [wlan0] wl_run_escan : LEGACY_SCAN sync ID: 9, >>>>>> bssidx: 0 >>>>>> [ 230.082903] rockchip-vop2 fe040000.vop: >>>>>> [drm:vop2_crtc_atomic_disable] Crtc atomic disable vp0 >>>>>> [ 230.116490] [drm:vop2_plane_atomic_check] *ERROR* Cluster0-win0 is >>>>>> invisible(src: pos[0, 0] rect[64 x 64] dst: pos[1583, 1598] rect[64 x >>>>>> 64] >>>>>> [ 230.187909] rockchip-vop2 fe040000.vop: >>>>>> [drm:vop2_crtc_atomic_enable] Update mode to 1920x1080p120, type: >>>>>> 11(if:800, flag:0x0) for vp0 dclk: 297000000 >>>>>> [ 246.747224] rockchip-vop2 fe040000.vop: >>>>>> [drm:vop2_crtc_atomic_disable] Crtc atomic disable vp0 >>>>>> [ 246.763535] rockchip-vop2 fe040000.vop: >>>>>> [drm:vop2_crtc_atomic_enable] Update mode to 1920x1080p60, type: >>>>>> 11(if:800, flag:0x0) for vp0 dclk: 148500000 >>>>>> [ 312.402381] [dhd] [wlan0] wl_run_escan : LEGACY_SCAN sync ID: 10, >>>>>> bssidx: 0 >>>>>> [ 412.212143] usb 1-1.1: USB disconnect, device number 8 >>>>>> [ 412.570255] usb 1-1.4: USB disconnect, device number 9 >>>>>> [ 413.063258] usb 1-1.4: new low-speed USB device number 10 using >>>>>> xhci-hcd >>>>>> [ 413.258781] usb 1-1.4: New USB device found, idVendor=046d, >>>>>> idProduct=c31c, bcdDevice=64.02 >>>>>> [ 413.258816] usb 1-1.4: New USB device strings: Mfr=1, Product=2, >>>>>> SerialNumber=0 >>>>>> [ 413.258825] usb 1-1.4: Product: USB Keyboard >>>>>> [ 413.258833] usb 1-1.4: Manufacturer: Logitech >>>>>> [ 413.338520] input: Logitech USB Keyboard as >>>>>> /devices/platform/usbhost/fd000000.dwc3/xhci-hcd.4.auto/usb1/1-1/1-1.4/1-1.4:1.0/0003:046D:C31C.0011/input/input27 >>>>>> [ 413.394022] hid-generic 0003:046D:C31C.0011: input,hidraw0: USB HID >>>>>> v1.10 Keyboard [Logitech USB Keyboard] on usb-xhci-hcd.4.auto-1.4/input0 >>>>>> [ 413.402397] input: Logitech USB Keyboard Consumer Control as >>>>>> /devices/platform/usbhost/fd000000.dwc3/xhci-hcd.4.auto/usb1/1-1/1-1.4/1-1.4:1.1/0003:046D:C31C.0012/input/input28 >>>>>> [ 413.457068] input: Logitech USB Keyboard System Control as >>>>>> /devices/platform/usbhost/fd000000.dwc3/xhci-hcd.4.auto/usb1/1-1/1-1.4/1-1.4:1.1/0003:046D:C31C.0012/input/input29 >>>>>> [ 413.457645] hid-generic 0003:046D:C31C.0012: input,hiddev96,hidraw1: >>>>>> USB HID v1.10 Device [Logitech USB Keyboard] on >>>>>> usb-xhci-hcd.4.auto-1.4/input1 >>>>>> [ 415.589983] usb 1-1.2: new high-speed USB device number 11 using >>>>>> xhci-hcd >>>>>> [ 415.781101] usb 1-1.2: New USB device found, idVendor=0781, >>>>>> idProduct=5583, bcdDevice= 1.00 >>>>>> [ 415.781138] usb 1-1.2: New USB device strings: Mfr=1, Product=2, >>>>>> SerialNumber=3 >>>>>> [ 415.781149] usb 1-1.2: Product: SanDisk 3.2Gen1 >>>>>> [ 415.781157] usb 1-1.2: Manufacturer: USB >>>>>> [ 415.781166] usb 1-1.2: SerialNumber: >>>>>> 05016efe255b095ca37d7cfd7cae5eeabf2a28f4e4e9fd61b8aa8177cbd545deddd80000000000000000000088e142f0ff190a10835581075e2a041c >>>>>> [ 415.782270] usb-storage 1-1.2:1.0: USB Mass Storage device detected >>>>>> [ 415.783069] scsi host0: usb-storage 1-1.2:1.0 >>>>>> [ 416.801089] scsi 0:0:0:0: Direct-Access USB SanDisk >>>>>> 3.2Gen1 1.00 PQ: 0 ANSI: 6 >>>>>> [ 416.802789] sd 0:0:0:0: [sda] 60088320 512-byte logical blocks: >>>>>> (30.8 GB/28.7 GiB) >>>>>> [ 416.803281] sd 0:0:0:0: [sda] Write Protect is off >>>>>> [ 416.803302] sd 0:0:0:0: [sda] Mode Sense: 43 00 00 00 >>>>>> [ 416.805948] sd 0:0:0:0: [sda] Write cache: disabled, read cache: >>>>>> enabled, doesn't support DPO or FUA >>>>>> [ 416.883060] sda: sda1 sda4 >>>>>> [ 416.886113] sd 0:0:0:0: [sda] Attached SCSI removable disk >>>>>> [ 433.498482] [dhd] [wlan0] wl_run_escan : LEGACY_SCAN sync ID: 11, >>>>>> bssidx: 0 >>>>>> [ 443.700195] usb 1-1.2: USB disconnect, device number 11 >>>>>> [ 452.709967] usb 1-1.1: new full-speed USB device number 12 using >>>>>> xhci-hcd >>>>>> [ 452.903722] usb 1-1.1: New USB device found, idVendor=046d, >>>>>> idProduct=c52b, bcdDevice=24.11 >>>>>> [ 452.903759] usb 1-1.1: New USB device strings: Mfr=1, Product=2, >>>>>> SerialNumber=0 >>>>>> [ 452.903768] usb 1-1.1: Product: USB Receiver >>>>>> [ 452.903776] usb 1-1.1: Manufacturer: Logitech >>>>>> [ 453.016266] input: Logitech USB Receiver as >>>>>> /devices/platform/usbhost/fd000000.dwc3/xhci-hcd.4.auto/usb1/1-1/1-1.1/1-1.1:1.0/0003:046D:C52B.0013/input/input30 >>>>>> [ 453.070710] hid-generic 0003:046D:C52B.0013: input,hidraw2: USB HID >>>>>> v1.11 Keyboard [Logitech USB Receiver] on usb-xhci-hcd.4.auto-1.1/input0 >>>>>> [ 453.075931] input: Logitech USB Receiver Mouse as >>>>>> /devices/platform/usbhost/fd000000.dwc3/xhci-hcd.4.auto/usb1/1-1/1-1.1/1-1.1:1.1/0003:046D:C52B.0014/input/input31 >>>>>> [ 453.076342] input: Logitech USB Receiver Consumer Control as >>>>>> /devices/platform/usbhost/fd000000.dwc3/xhci-hcd.4.auto/usb1/1-1/1-1.1/1-1.1:1.1/0003:046D:C52B.0014/input/input32 >>>>>> [ 453.133765] input: Logitech USB Receiver System Control as >>>>>> /devices/platform/usbhost/fd000000.dwc3/xhci-hcd.4.auto/usb1/1-1/1-1.1/1-1.1:1.1/0003:046D:C52B.0014/input/input33 >>>>>> [ 453.134201] hid-generic 0003:046D:C52B.0014: input,hiddev97,hidraw3: >>>>>> USB HID v1.11 Mouse [Logitech USB Receiver] on >>>>>> usb-xhci-hcd.4.auto-1.1/input1 >>>>>> [ 453.138582] hid-generic 0003:046D:C52B.0015: hiddev98,hidraw4: USB >>>>>> HID v1.11 Device [Logitech USB Receiver] on >>>>>> usb-xhci-hcd.4.auto-1.1/input2 >>>>>> >>>>>> >>>>>> --Z-- >>>>> >>>>> -- >>>>> --Z-- >>>> >>>> -- >>>> --Z-- >>> >>> -- >>> --Z-- >> >> -- >> --Z-- > > -- > --Z-- -- --Z--
