On Sat, 28 Oct 2023 16:44:06 -0600
jone...@hrothgars.net wrote:
> I am trying to boot the OpenBSD installer on an Orangepi 5 board. I
> know the board is yet not in the upstream u-boot and Linux, but I
> thought I would try to build the u-boot following the Orangepi user
> manual. I did test the u-boot by installing it on to a new SD using
> the nand-data-install script outlined in the Orangepi user manual.
>
> To build the OpenBSD installation media I took the following steps
>
> Copy the minroot image from the 2023.10.27 snaphot
> dd if=arm64_20231027_miniroot74.img of=/dev/rsd2c bs=1m
>
> After mounting the SD card to /mnt, I copied the device tree blob to
> the SD card cp rk3588s-orangepi-5.dtb /mnt/rockchip/.
>
> Copy the u-boot bits using dd as described in the OpenBSD
> INSTALL.arm64 file. dd if=idbloader.img of=/dev/sd2c seek=64
> dd if=u-boot.itb of=/dev/sd2c seek=16384
>
> The Orangepi5 board attempts to book from the SD card but reports a
> GPT errors. I also tried installing the u-boot bits using the
> nand-sata-install script outlined in the Orangepi user manual with
> the same result. Console output is listed below.
>
> I am sure I am missing something obvious. Thanks in advance for any
> suggestions.
>
<snip some u-boot output>
>
I'm trying to do the same, but the step taken to handle u-boot are
different, but taken from the rockchip instructions in the
INSTALL.arm64 file :)
# pkg_add u-boot-rk3588
# dd if=miniroot74.img of=/dev/rsdXc bs=1m
# dd if=/usr/local/share/u-boot/orangepi-5-rk3588s/u-boot-rockchip.bin
of=/dev/sd1c seek=64
After this I tried to boot the orangpi-5, but it hangs while trying to
start OHCI driver
U-Boot 2024.01-rc3 (Feb 10 2024 - 02:29:31 -0700)
Model: Xunlong Orange Pi 5
DRAM: 4 GiB (effective 3.7 GiB)
Core: 315 devices, 29 uclasses, devicetree: separate
MMC: mmc@fe2c0000: 0
Loading Environment from nowhere... OK
In: serial@feb50000
Out: serial@feb50000
Err: serial@feb50000
Model: Xunlong Orange Pi 5
Net: eth0: ethernet@fe1c0000
Hit any key to stop autoboot: 0
** Booting bootflow 'mmc@fe2c0000.bootdev.part_1' with efi
No EFI system partition
No EFI system partition
Failed to persist EFI variables
Booting /efi\boot\bootaa64.efi
disks: sd0*
>> OpenBSD/arm64 BOOTAA64 1.18
boot>
cannot open sd0a:/etc/random.seed: No such file or directory
booting sd0a:/bsd: 3010708+1211524+12712736+636688
[261438+91+699216+285720]=0x13eba38
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights
reserved.
Copyright (c) 1995-2024 OpenBSD. All rights reserved.
https://www.OpenBSD.org
OpenBSD 7.4-current (RAMDISK) #70: Sun Feb 11 00:41:15 MST 2024
dera...@arm64.openbsd.org:/usr/src/sys/arch/arm64/compile/RAMDISK
real mem = 4022718464 (3836MB)
avail mem = 3857891328 (3679MB)
random: boothowto does not indicate good seed
mainbus0 at root: Xunlong Orange Pi 5
psci0 at mainbus0: PSCI 1.1, SMCCC 1.2, SYSTEM_SUSPEND
efi0 at mainbus0: UEFI 2.10
efi0: Das U-Boot rev 0x20240100
smbios0 at efi0: unsupported SMBIOS entry point
cpu0 at mainbus0 mpidr 0: ARM Cortex-A55 r2p0
cpu0: 32KB 64b/line 4-way L1 VIPT I-cache, 32KB 64b/line 4-way L1
D-cache
cpu0: 128KB 64b/line 4-way L2 cache
cpu0: 4096KB 64b/line 16-way L3 cache
cpu0:
DP,RDM,Atomic,CRC32,SHA2,SHA1,AES+PMULL,LRCPC,DPB,ASID16,PAN+ATS1E1,LO,HPDS,VH,HAFDBS,SBSS
"optee" at mainbus0 not configured
scmi0 at mainbus0: SCMI 2.0
"gap2" at mainbus0 not configured
"gap1" at mainbus0 not configured
syscon0 at mainbus0: "syscon"
syscon1 at mainbus0: "syscon"
syscon2 at mainbus0: "syscon"
syscon3 at mainbus0: "syscon"
syscon4 at mainbus0: "syscon"
"usb2-phy" at syscon4 not configured
syscon5 at mainbus0: "syscon"
"usb2-phy" at syscon5 not configured
syscon6 at mainbus0: "syscon"
rkclock0 at mainbus0
syscon7 at mainbus0: "power-management"
"power-controller" at syscon7 not configured
syscon8 at mainbus0: "qos"
syscon9 at mainbus0: "qos"
syscon10 at mainbus0: "qos"
syscon11 at mainbus0: "qos"
syscon12 at mainbus0: "qos"
syscon13 at mainbus0: "qos"
syscon14 at mainbus0: "qos"
syscon15 at mainbus0: "qos"
syscon16 at mainbus0: "qos"
syscon17 at mainbus0: "qos"
syscon18 at mainbus0: "qos"
syscon19 at mainbus0: "qos"
syscon20 at mainbus0: "qos"
syscon21 at mainbus0: "qos"
syscon22 at mainbus0: "qos"
syscon23 at mainbus0: "qos"
syscon24 at mainbus0: "qos"
syscon25 at mainbus0: "qos"
syscon26 at mainbus0: "qos"
syscon27 at mainbus0: "qos"
syscon28 at mainbus0: "qos"
syscon29 at mainbus0: "qos"
syscon30 at m at mainbus0: "qos"
syscon32 at mainbus0: "qos"
syscon33 at mainbus0: "qos"
syscon34 at mainbus0: "qos"
syscon35 at mainbus0: "qos"
syscon36 at mainbus0: "qos"
syscon37 at mainbus0: "qos"
syscon38 at mainbus0: "qos"
syscon39 at mainbus0: "qos"
syscon40 at mainbus0: "qos"
syscon41 at mainbus0: "qos"
syscon42 at mainbus0: "qos"
syscon43 at mainbus0: "qos"
syscon44 at mainbus0: "qos"
syscon45 at mainbus0: "qos"
syscon46 at mainbus0: "qos"
syscon47 at mainbus0: "qos"
syscon48 at mainbus0: "qos"
syscon49 at mainbus0: "qos"
syscon50 at mainbus0: "qos"
syscon51 at mainbus0: "qos"
syscon52 at mainbus0: "qos"
syscon53 at mainbus0: "qos"
syscon54 at mainbus0: "qos"
syscon55 at mainbus0: "qos"
agintc0 at mainbus0 mbi shift 4:4 nirq 512 nredist 8:
"interrupt-controller"
agintcmsi0 at agintc0
agintcmsi1 at agintc0
rkcomphy0 at mainbus0
rkcomphy1 at mainbus0
rkpinctrl0 at mainbus0: "pinctrl"
rkgpio0 at rkpinctrl0
rkgpio1 at rkpinctrl0
rkgpio2 at rkpinctrl0
rkgpio3 at rkpinctrl0
rkgpio4 at rkpinctrl0
syscon56 at mainbus0: "syscon"
syscon57 at mainbus0: "syscon"
syscon58 at mainbus0: "syscon"
syscon59 at mainbus0: "syscon"
syscon60 at mainbus0: "syscon"
"fit-images" at mainbus0 not configured
"firmware" at mainbus0 not configured
"pmu-a55" at mainbus0 not configured
"pmu-a76" at mainbus0 not configured
"clock-0" at mainbus0 not configured
agtimer0 at mainbus0: 24000 kHz
"clock-1" at mainbus0 not configured
"clock-2" at mainbus0 not configured
"sram" at mainbus0 not configured
ehci0 at mainbus0
usb0 at ehci0: USB revision 2.0
uhub0 at usb0 configuration 1 interface 0 "Generic EHCI root hub" rev
2.00/1.00 addr 1
ohci0 at mainbus0��
[EOT]
Looks like quite some thing are not properly configured yet.
BR/Rob
