Oops ... I found out my problem span=.... --- jerk face <[EMAIL PROTECTED]> wrote: > I am using a crossover cable. > My channel definitions are: > fxoks=1-22 > fxsks=23-24 > in zaptel.conf > > > --- Alex Lopez <[EMAIL PROTECTED]> wrote: > > > > What cable are you using, The SU600 to Digium > cards > > need a crossover > > cable. > > > > 1 to 4 > > 2 to 5 > > 4 to 1 > > 5 to 2 > > > > That would stop it from not working, > > > > also make sure that you have a span definition on > > the zaptel.con file. > > > > > > > > Message: 7 > > Date: Mon, 25 Aug 2003 12:52:12 -0700 (PDT) > > From: jerk face <[EMAIL PROTECTED]> > > Subject: RE: [Asterisk-Users] T100P/ TSU 600 > > installation problem > > To: [EMAIL PROTECTED] > > Reply-To: [EMAIL PROTECTED] > > > > Each port is set to the proper signalling type > (FXO, > > FXS). I can't find any other options for the > > individual ports. > > As for the timing and configuration of NI, I have > > tried > > NI: > > Timing Mode as both DTE and NI (my only choices) > > > > Where else should I be checking? > > (Before this morning, I hadn't even seen a channel > > bank before, so I'm a little lost at the moment). > > > > Thanks for your time. > > > > --- Wade Weppler <[EMAIL PROTECTED]> wrote: > > > Have you configured the TSU600 properly? You > have > > > to allocate each FXO/FXS > > > channel to a timeslot before it will work. This > > is > > > not automatically done > > > (like the Adtran Total Access series). > > > > > > Mind you, you should still have a sync light on > > the > > > T1 card... > > > > > > -wade > > > > > > > -----Original Message----- > > > > From: [EMAIL PROTECTED] > > > [mailto:asterisk-users- > > > > [EMAIL PROTECTED] On Behalf Of jerk face > > > > Sent: Monday, August 25, 2003 3:01 PM > > > > To: [EMAIL PROTECTED] > > > > Subject: RE: [Asterisk-Users] T100P/ TSU 600 > > > installation problem > > > > > > > > My zapata.conf is located in /etc/asterisk and > > my > > > > zaptel.conf is located in the /etc directory. > > > > > > > > --- "Adams, Gavin" <[EMAIL PROTECTED]> > wrote: > > > > > > -----Original Message----- > > > > > > From: jerk face > > > [mailto:[EMAIL PROTECTED] > > > > > > > > > > > > > > > > I seem to be having a problem with the > T100P > > > card. > > > > > So > > > > > > far I have done the following: > > > > > > > > > > > > vi zaptel.conf > > > > > > fxoks=1-22 > > > > > > fxsks=23-24 > > > > > > ... > > > > > > > > > > > > vi zapata.conf > > > > > > ... > > > > > > signalling=fxo_ks > > > > > > ... > > > > > > channel => 1-22 > > > > > > ... > > > > > > signalling=fxs_ks > > > > > > ... > > > > > > channel => 23-24 > > > > > > > > > > > > I then run > > > > > > modprobe zaptel > > > > > > modprobe wct1xxp > > > > > > ztcfg -vv > > > > > > > > > > > > There are no errors to report. In > > > /proc/zaptel/1 > > > > > all > > > > > > of the configured channels are listed. > > > > > > > > > > Crazy question, is zaptel.conf is /etc or > > > > > /etc/asterisk? If the latter, > > > > > try: > > > > > > > > > > ztcfg -c /etc/asterisk/zaptel.conf -vvv > > > > > > > > > > --- Gavin > > > > > > > > > > > > _______________________________________________ > > > > > Asterisk-Users mailing list > > > > > [EMAIL PROTECTED] > > > > > > > > > > > > > > > http://lists.digium.com/mailman/listinfo/asterisk-users > > > __________________________________ > Do you Yahoo!? > Yahoo! SiteBuilder - Free, easy-to-use web site > design software > http://sitebuilder.yahoo.com > _______________________________________________ > Asterisk-Users mailing list > [EMAIL PROTECTED] > http://lists.digium.com/mailman/listinfo/asterisk-users
__________________________________ Do you Yahoo!? Yahoo! SiteBuilder - Free, easy-to-use web site design software http://sitebuilder.yahoo.com _______________________________________________ Asterisk-Users mailing list [EMAIL PROTECTED] http://lists.digium.com/mailman/listinfo/asterisk-users
