Hi Steve, the Eicon Diva Server BRI cards support NI-1 with capi. Some people in .us are using them. Unfortunately AVM only put EuroISDN into their binary kernel module. :(
Are you sure that incoming callerid is included in your "FastTrak ISDN"? i could imagine that SBC will rip you off extra for it! ;) regards kapejod -- Klaus-Peter Junghanns CEO,CTO Junghanns.NET GmbH Breite Strasse 13 - 12167 Berlin - Germany fon: +49 30 79705392 fax: +49 30 79705391 iaxtel: 1-700-157-8753 email: [EMAIL PROTECTED] http://www.junghanns.net/asterisk Am Mon, 2003-09-15 um 23.10 schrieb Steve Haehnichen: > I have a North American BRI configured as National ISDN (NI-1) on an > SBC (Nortel?) switch. SBC calls this "FastTrak ISDN", and it's > surprisingly inexpensive -- less than two POTS lines. > > I've been trying to find an inexpensive PCI interface solution to > connect this to Asterisk as voice lines. I prefer ISDN BRI over POTS > lines because of the improved signalling, fast dialing, clean audio, > and so on. > > I've tried three different Passive ISDN boards supported by the HiSax > drivers, with various degrees of failure. None have been able to > complete a call. (Linux kernel 2.4.22, with AVM Fritz, DynaFax, and > HFC cards) > > According to the HiSax documentation, NI-1 is a supported protocol. > > From what I can find on CAPI, it supports only EuroISDN: > http://www.junghanns.net/asterisk/page15.html > Is this the case for all Linux CAPI drivers? Bummer. > > Has anyone successfully used Asterisk with a HiSax passive ISDN card > on a National-1 (or NI-2) dialing plan? It would really mean a whole > lot just to hear that someone is doing it with success. :) > > > How does one specify a SPID in Asterisk? I've done an archive search > and came up blank for "spid". BRI (2B+D) provisioning on SBC is done > with two Directory Numbers and two SPIDs, like this: > > DN1: 794-7601 > DN2: 794-7602 > > SPID1: 858-794-7601-0101 > SPID2: 858-794-7602-0101 > > (SBC said the -0101 is used on all NI-1 SPIDs) > > I'm not sure how to inform Asterisk/HiSax of the SPID part, and I get > a "SPID not supplied in EAZMSN" from the ISDN driver. > > I've tried various permutations of AT&E7947601:85879476010101 manually > into the /dev/ttyI0 interface, with no luck. > > Last, according to the kernel messages, there never seems to be an OAD > (Caller-ID) on incoming calls. I've used an ISDN protocol analyzer to > show that the incoming setup does contain the calling number. Again, > I'm just curious to compare notes with someone else doing this. > > Thanks! > > -Steve > > My modem.conf: > > [interfaces] > context=isdn-in > driver=i4l > language=en > type=autodetect > stripmsd=0 > dialtype=tone > mode=immediate > > group=1 > msn=7947601 > incomingmsn=* > context=isdn-in > device => /dev/ttyI0 > device => /dev/ttyI1 > > ------- > > My Kernel log: > > ISDN subsystem Rev: 1.1.4.1/1.1.4.1/1.1.4.1/none/1.1.4.1/1.1.4.1 loaded > HiSax: Linux Driver for passive ISDN cards > HiSax: Version 3.5 (module) > HiSax: Layer1 Revision 1.1.4.1 > HiSax: Layer2 Revision 1.1.4.1 > HiSax: TeiMgr Revision 1.1.4.1 > HiSax: Layer3 Revision 1.1.4.1 > HiSax: LinkLayer Revision 1.1.4.1 > HiSax: Total 1 card defined > HiSax: Card 1 Protocol NI1 Id=HFC (0) > HiSax: HFC-PCI driver Rev. 1.1.4.1 > HiSax: HFC-PCI card manufacturer: CCD/Billion/Asuscom card name: 2BD0 > HFC-PCI: defined at mem 0xe095dc00 fifo 0xd9e88000(0x19e88000) IRQ 5 HZ 100 > HFC_PCI: resetting card > HFC 2BDS0 PCI: IRQ 5 count 0 > HFC 2BDS0 PCI: IRQ 5 count 34 > HiSax: National ISDN-1 Rev. 1.1.4.1 > HiSax: National ISDN-1 Rev. 1.1.4.1 > HiSax: 2 channels added > HiSax: MAX_WAITING_CALLS added > ... > isdn_net: call from 0 -> 0 7947601 ignored > isdn_tty: Incoming call without OAD, assuming '0' > isdn_tty: call from 0, -> RING on ttyI1 > SPID not supplied in EAZMSN > isdn: HFC,ch0 cause: 001B > isdn: HFC,ch1 cause: 6F15 > isdn_net: Incoming call without OAD, assuming '0' > isdn_net: call from 0 -> 0 7947601 ignored > isdn_tty: Incoming call without OAD, assuming '0' > isdn_tty: call from 0, -> RING on ttyI0 > isdn_net: Incoming call without OAD, assuming '0' > isdn_net: call from 0 -> 0 7947601 ignored > isdn_tty: Incoming call without OAD, assuming '0' > isdn_tty: call from 0, -> RING on ttyI1 > isdn: HFC,ch0 cause: 001B > isdn_net: Incoming call without OAD, assuming '0' > isdn_net: call from 0 -> 0 7947601 ignored > isdn_tty: Incoming call without OAD, assuming '0' > isdn_tty: call from 0, -> RING on ttyI0 > SPID not supplied in EAZMSN > _______________________________________________ > Asterisk-Users mailing list > [EMAIL PROTECTED] > http://lists.digium.com/mailman/listinfo/asterisk-users _______________________________________________ Asterisk-Users mailing list [EMAIL PROTECTED] http://lists.digium.com/mailman/listinfo/asterisk-users
