Have your tried switchtype=5ess? On Mon, 2003-09-15 at 17:13, tony mancill wrote: > > I have a T1 PRI from the telco and have been trying to get it to work > > with the wildcard T400P. > > > > I know framing and coding is esf and b8zs. what else should I be > > putting into the zaptel.conf and zapata.conf. > > > > Dave Anderson > > I've got basically the same question. After building everything, I edited > zaptel.conf to include: > > span=1,0,0,esf,b8zs > bchan=1-23 > dchan=24 > loadzone = us > defaultzone=us > > Then, after: > > modprobe wct4xxp > > in dmesg, you'll see something like: > > Found TE410P at base address fe3ffc00, remapped to f8977c00 > TE410P version c01a003a > FALC version: 00000005, Board ID: 00 > Reg 0: 0x2edfd800 > Reg 1: 0x2edfd000 > Reg 2: 0x07fc07fc > Reg 3: 0x00000000 > Reg 4: 0x00000000 > Reg 5: 0x00000000 > Reg 6: 0xc01a003a > Reg 7: 0x00001000 > Reg 8: 0x00000000 > Reg 9: 0x00ff0000 > Reg 10: 0x00000000 > TE410P: Launching card: 0 > TE410P: Setting up global serial parameters > TE410P: Timing from source 0 > Found a Wildcard: Wildcard TE410P-Xilinx > Registered tone zone 0 (United States / North America) > TE410P: Span 1 configured for ESF/B8ZS > > (I also noticed that you can use /sbin/ztcfg to reread /etc/zaptel.conf > after it's been changed.) > > So far, I figured I was on the right path. So then I edited zapata.conf > to include: > > switchtype=4ess > signalling=pri_cpe > group = 1 > channel => 1-23 > > However, I can no longer start asterisk. It doesn't seem to like the > signalling, spitting out the following on startup: > > .. > [chan_zap.so] => (Zapata Telephony) > == Parsing '/etc/asterisk/zapata.conf': Found > WARNING[1024]: File chan_zap.c, Line 6890 (load_module): Ignoring switchtype > ERROR[1024]: File chan_zap.c, Line 6834 (load_module): Unknown signalling > method 'pri_cpe' > ERROR[1024]: File chan_zap.c, Line 6603 (load_module): Signalling must be > specified before any channels are. > WARNING[1024]: File loader.c, Line 301 (ast_load_resource): chan_zap.so: > load_module failed, returning -1 > WARNING[1024]: File loader.c, Line 396 (load_modules): Loading module > chan_zap.so failed! > > Any information on how to get futher would be greatly appreciated. None > of the examples I've been able to find seem to be geared towards ISDN > DS1s. > > Thanks, > tony > > > _______________________________________________ > Asterisk-Users mailing list > [EMAIL PROTECTED] > http://lists.digium.com/mailman/listinfo/asterisk-users -- BTEL Consulting +1-850-484-4535 x2111 (Pensacola) +1-504-595-3916 x2111 (New Orleans) +1-877-677-9643 x2111 (Toll Free)
_______________________________________________ Asterisk-Users mailing list [EMAIL PROTECTED] http://lists.digium.com/mailman/listinfo/asterisk-users
