Still not resolved
On Wed, 2005-06-08 at 01:16, David John Walsh wrote: > Frank > > Did you ever resolve this? If so what was the issue? > > On 03/05/05, list <[EMAIL PROTECTED]> wrote: > > Hi, > > I am struggling to get rid of a conflict on DELL 2800 : PCI Parity error > > (EB113 on the display) > > I am learning linux and asterisk as I go along, there might be obvious > > things I should know, but bear with me. > > > > >From demsg below my 2 digium cards installed are listed (no config or > > connections done to digium cards yet), the conflict is with the TDM400P > > card, without that card, in any slot, no alarm. > > > > Zapata Telephony Interface Registered on major 196 > > Registered Tormenta2 PCI > > Controller version: 24 > > FALC version: 00000000 > > TE110P: Setting up global serial parameters for E1 FALC V1.2 > > TE110P: Successfully initialized serial bus for card > > Found a Wildcard: Digium Wildcard TE110P T1/E1 > > Freshmaker version: 71 > > Freshmaker passed register test > > Uhhuh. NMI received. Dazed and confused, but trying to continue > > You probably have a hardware problem with your RAM chips > > Module 0: Installed -- AUTO FXS/DPO > > Module 1: Not installed > > Module 2: Not installed > > Module 3: Installed -- AUTO FXO (FCC mode) > > Found a Wildcard TDM: Wildcard TDM400P REV E/F (4 modules) > > Registered tone zone 8 (Norway) > > TE110P: Span configured for CCS/HDB3/CRC4 > > Calling startup (flags is 4099) > > wcte1xxp: Setting yellow alarm > > usb.c: registered new driver wcusb > > Wildcard USB FXS Interface driver registered > > TE110P: Span configured for CCS/HDB3/CRC4 > > Calling startup (flags is 4099) > > Registered tone zone 8 (Norway) > > TE110P: Span configured for CCS/HDB3/CRC4 > > Calling startup (flags is 4099) > > Registered tone zone 8 (Norway) > > > > ramchip problem is false, without the card all ok, ramtests on machine > > as well. > > > > lsmod shows wcusb driver on zaptel, I dont need that, can I remove it? > > is that a problem or not? > > > > # lsmod > > Module Size Used by Not tainted > > usbserial 23964 0 (autoclean) (unused) > > lp 9156 0 (autoclean) > > parport 38848 0 (autoclean) [lp] > > autofs4 16984 0 (autoclean) (unused) > > wcusb 19552 0 (unused) > > wctdm 41088 0 (unused) > > wcte11xp 22048 0 (unused) > > zaptel 182080 4 [wcusb wctdm wcte11xp] > > e1000 77884 1 (autoclean) > > floppy 57552 0 (autoclean) > > sg 37388 0 (autoclean) > > microcode 6912 0 (autoclean) > > ide-cd 34016 0 (autoclean) > > cdrom 32896 0 (autoclean) [ide-cd] > > keybdev 2976 0 (unused) > > mousedev 5688 1 > > hid 22308 0 (unused) > > input 6176 0 [keybdev mousedev hid] > > ehci-hcd 20776 0 (unused) > > usb-uhci 26860 0 (unused) > > usbcore 81152 1 [usbserial wcusb hid ehci-hcd > > usb-uhci] > > ext3 89960 6 > > jbd 55060 6 [ext3] > > megaraid2 38344 7 > > diskdumplib 5228 0 [megaraid2] > > sd_mod 13904 14 > > scsi_mod 115112 2 [sg megaraid2 sd_mod] > > > > finally my interrupts, bit confusing to me, looks like I have dual > > processor, can see the NMI but what else can be found here? > > > > # cat /proc/interrupts > > CPU0 CPU1 > > 0: 3298395 3303167 IO-APIC-edge timer > > 1: 3300 2876 IO-APIC-edge keyboard > > 2: 0 0 XT-PIC cascade > > 8: 0 1 IO-APIC-edge rtc > > 12: 236637 237965 IO-APIC-edge PS/2 Mouse > > 14: 261779 262965 IO-APIC-edge ide0 > > 16: 0 0 IO-APIC-level usb-uhci > > 18: 0 0 IO-APIC-level usb-uhci > > 19: 0 0 IO-APIC-level usb-uhci > > 23: 0 24 IO-APIC-level ehci-hcd > > 29: 33133540 32846566 IO-APIC-level t1xxp > > 38: 72500 83317 IO-APIC-level megaraid > > 58: 32838989 33150525 IO-APIC-level wctdm > > 72: 222855 12 IO-APIC-level eth0 > > NMI: 1 0 > > LOC: 6601462 6601460 > > ERR: 0 > > MIS: 0 > > > > any suggestions from someone experienced something similar? > > > > regards > > Frank > > _______________________________________________ > > Asterisk-Users mailing list > > [email protected] > > http://lists.digium.com/mailman/listinfo/asterisk-users > > To UNSUBSCRIBE or update options visit: > > http://lists.digium.com/mailman/listinfo/asterisk-users > > > _______________________________________________ > Asterisk-Users mailing list > [email protected] > http://lists.digium.com/mailman/listinfo/asterisk-users > To UNSUBSCRIBE or update options visit: > http://lists.digium.com/mailman/listinfo/asterisk-users _______________________________________________ Asterisk-Users mailing list [email protected] http://lists.digium.com/mailman/listinfo/asterisk-users To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
